Transition Networks CSDTF1022-100 Benutzerhandbuch
INSTALLATION
(continued)
Install Slide-In-Module in PointSystem
™
Chassis
CAUTION: Any Slide-in-Module installation slot in which a Media Converter
Slide-in-Module is NOT installed MUST have a protective plate instead.
Failure to observe this caution will void Class A and/or Class B compliance.
Slide-in-Module is NOT installed MUST have a protective plate instead.
Failure to observe this caution will void Class A and/or Class B compliance.
NOTE: Install Media Converter Slide-in-Modules in any slot, in any order.
1.
Carefully slide Media Converter Slide-in-Module into installation slot,
aligning Media Converter Slide-in-Module with installation guides.
aligning Media Converter Slide-in-Module with installation guides.
NOTE: Ensure that Slide-in-Module is firmly seated against backplane.
2.
Secure Slide-in-Module by securing panel fastener screw (attached to
Slide-in-Module) to chassis front.
Slide-in-Module) to chassis front.
3.
Install protective plate at EVERY Slide-in-Module installation slot in
which a Media Converter Slide-in-Module is not installed by securing
attached protective plate panel fastener screw to chassis front.
which a Media Converter Slide-in-Module is not installed by securing
attached protective plate panel fastener screw to chassis front.
Install Cable
COPPER
T1 100 OHM (RJ-45 CONNECTOR)
1.
Locate or build twisted-pair cables that are compliant with
specifications on page 10, with RJ-45 plug connectors at both ends.
specifications on page 10, with RJ-45 plug connectors at both ends.
2.
Ensure that MDI/MDI-X switch is set according to network
conditions.
conditions.
3.
Connect RJ-45 plug connector at one end of cable to media
converter RJ-45 jack connector.
converter RJ-45 jack connector.
4.
Connect RJ-45 plug connector at other end of cable to network
equipment.
equipment.
FIBER
1.
Locate or build fiber cables that are compliant with specifications
on page 9, with male two-stranded TX to RX connectors installed at
both ends.
on page 9, with male two-stranded TX to RX connectors installed at
both ends.
2.
Connect cable with connector installed at TX location on media
converter to RX location on attached device.
converter to RX location on attached device.
3.
Connect cable with connector installed at RX location on media
converter to TX location on attached device.
converter to TX location on attached device.
Power the Slide-In-Module
NOTE: The Slide-In-Module is powered through the
Conversion
Center
™
.
OPERATION
After installation, the media converter should function without operator
intervention.
intervention.
Status LEDs
Use the status LEDs to monitor media converter operation in the network.
SDC
Signal Detect/Copper - Steady LED
indicates twisted-pair copper link is up.
indicates twisted-pair copper link is up.
Flashing LED (once/second) indicates
transmitting on link if other link is down.
transmitting on link if other link is down.
Flashing LED (5 times/second) indicates All
Ones detected on Link.
Ones detected on Link.
SDF
Signal Detect/Fiber - Steady LED indicates fiber link is up.
Flashing LED (once/second) indicates transmitting on link if
other link is down.
other link is down.
Flashing LED (5 times/second) indicates All Ones detected on
Link.
Link.
P(o)W(e)R
Steady green LED indicates connection to external AC power.
Using SNMP*
Use SNMP at an attached terminal or at a remote location to:
•
Monitor media converter by monitoring:
Media Converter Power
Fiber Link Status
Copper Link Status
Hardware Switch settings
AIS detected on Fiber
AIS detected on Copper
•
Enter network commands that:
Enable/disable Loop-back on Fiber
Enable/disable Transmit All Ones on Fiber when Copper is down
Enable/disable Transmit All Ones on Copper when Fiber is down
Power Down Media Converter.
*See the on-line documentation that comes with TRANSITION Networks
FocalPoint
FocalPoint
™
software for applicable commands and usage.
PWR
SDF
SDC
LOOP
TX
RX
TX
RX