Transition Networks AR-CF-02(SC) Merkblatt
MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Standards
ANSI/ATA 878
Delay
300ns one-way
Case dimensions
4.75" x 3.0" x 1.0"
(119mm x 76mm x 25mm)
Shipping Weight
2 pounds
(0.9 kilograms)
Environment
Temperature:
0-40°C (32° to 104° F )
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Five years
Power Supply Requirements
Replace power supply with only the equivalent
input rating (see below) and output rating (regulated 9VDC at 0.2 A).
TN PN
Requirement
Location
3525
240 volts, 50 hertz
United Kingdom
3525
230 volts, 50 hertz
Europe
3518
120 volts, 60 hertz
USA/Canada/Mexico
3514
100 volts, 50-60 hertz
Japan
3525
240 volts, 50 hertz
Australia
NOTE: This product also can be powered by the Transition Networks E-MCR series media
converter rack.
converter rack.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
the radio interference regulations of the Canadian Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Copyright Restrictions
© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Trademark Notice
ARCNET is a registered trademark of Datapoint Corporation.
All registered trademarks and trademarks are the property of their respective owners.
All registered trademarks and trademarks are the property of their respective owners.
33095.B
The TRANSITION Networks ARCNET
®
Coax Copper/Fiber Media Converter
(AR-CF-02) extends the signal distance of an ARCNET
®
segment or node
link up to 2 kilometers over fiber*, up to 600 meters over coax cable in a star
topology, and up to 300 meters over coax cable in a bus topology.
A switch on the media converter allows the media converter to be used to
terminate the link or node signal.
topology, and up to 300 meters over coax cable in a bus topology.
A switch on the media converter allows the media converter to be used to
terminate the link or node signal.
STATUS LEDS
Power
Steady green LED indicates connection to external AC power.
Coax
Blinking green LED
indicates network
traffic on coaxial cable
link.
indicates network
traffic on coaxial cable
link.
Fiber
Blinking green LED
indicates network traffic on fiber link.
indicates network traffic on fiber link.
*Consider carefully the network constraints imposed by the maximum latency
response time of installed equipment. Some equipment cannot handle the extended
response time that 2 kilometers of fiber introduces.
response time of installed equipment. Some equipment cannot handle the extended
response time that 2 kilometers of fiber introduces.
Minneapolis, MN 55344 USA
ARCNET
®
Coax Copper/Fiber
Media Converter
AR-CF-02, AR-CF-02(SC), AR-CF-02(SM)
USER’S GUIDE
10BASE-T
RX
TX
Fiber
Power
Coax
AR-CF-02
Provides a BNC
connector to coaxial
cable and a set of RX
(receive) and TX
(transmit) ST connectors
to multimode fiber-optic
cable.
Provides a BNC
connector to coaxial
cable and a set of RX
(receive) and TX
(transmit) ST connectors
to multimode fiber-optic
cable.
AR-CF-02(SC)
Provides a BNC connector to
coaxial cable and an RX (receive)
and TX (transmit) SC connector to
multimode fiber-optic cable.
Provides a BNC connector to
coaxial cable and an RX (receive)
and TX (transmit) SC connector to
multimode fiber-optic cable.
AR-CF-02(SM)
Provides a BNC connector to
coaxial cable and an RX (receive)
ST and TX (transmit) SC connector
to singlemode fiber-optic cable.
Provides a BNC connector to
coaxial cable and an RX (receive)
ST and TX (transmit) SC connector
to singlemode fiber-optic cable.
AR-CF-02
ArcNet
Fiber to Coax
Media Converter
®