Benutzerhandbuch für Amana AMV9

Inhaltsverzeichnis

• I. Component Identification

  5
• II. Safety

  6
• ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

  6
• III. Product Application

  6
• IV. Location Requirements & Considerations

  7
• GENERAL

  7
• CLEARANCES AND ACCESSIBILITY

  8
• FURNACE SUSPENSION

  8
• EXISTING FURNACE REMOVAL

  8
• THERMOSTAT LOCATION

  9
• V. Combustion & Ventilation Air Requirements

  9
• VI. Installation Positions

  11
• VII. Horizontal Applications & Considerations

  11
• GENERAL

  11
• DRAIN TRAP AND LINES

  11
• LEVELING

  11
• ALTERNATE VENT/FLUE AND COMBUSTION AIR CONNECTIONS

  11
• ALTERNATE ELECTRICAL AND GAS LINE CONNECTIONS

  12
• DRAIN PAN

  12
• FREEZE PROTECTION

  12
• FURNACE SUSPENSION

  12
• VIII. Propane Gas /High Altitude Installations

  12
• IX. Vent/Flue Pipe & Combustion Air Pipe

  12
• GENERAL

  12
• DUAL CERTIFICATION: NON-DIRECT/DIRECT VENT

  12
• MATERIALS AND JOINING METHODS

  13
• PROPER VENT/FLUE AND COMBUSTION AIR PIPING PRACTICES

  13
• TERMINATION LOCATIONS

  13
• CANADIAN VENTING REQUIREMENTS

  13
• STANDARD FURNACE CONNECTIONS

  14
• ALTERNATE FURNACE CONNECTIONS

  14
• NON-DIRECT VENT (SINGLE PIPE) PIPING

  16
• DIRECT VENT (DUAL PIPE) PIPING

  17
• VENT/INTAKE TERMINATIONS FOR INSTALLATION OF MULTIPLE DIRECT VENT FURNACES

  18
• CONCENTRIC VENT TERMINATION

  18
• X. Condensate Drain Lines & Drain Trap

  18
• GENERAL

  18
• UPRIGHT INSTALLATIONS

  19
• HORIZONTAL INSTALLATIONS

  20
• XI. Electrical Connections

  21
• WIRING HARNESS

  21
• 115 VOLT LINE CONNECTIONS

  21
• 24 VOLT THERMOSTAT WIRING

  22
• SINGLE-STAGE THERMOSTAT APPLICATION

  22
• 24 VOLT DEHUMIDISTAT WIRING

  22
• FOSSIL FUEL APPLICATIONS

  23
• 115 VOLT LINE CONNECTION OF ACCESSORIES (HUMIDIFIER AND ELECTRONIC AIR CLEANER)

  23
• 24 VOLT HUMIDIFIER

  23
• XII. Gas Supply and Piping

  23
• GENERAL

  23
• GAS PIPING CONNECTIONS

  24
• PROPANE GAS TANKS AND PIPING

  25
• XIII. Circulating Air & Filters

  26
• DUCTWORK - AIR FLOW

  26
• BOTTOM RETURN AIR OPENING [UPFLOW MODELS]

  26
• FILTERS - READ THIS SECTION BEFORE INSTALLING THE RETURN AIR DUCTWORK

  27
• UPRIGHT INSTALLATIONS

  27
• HORIZONTAL INSTALLATIONS

  28
• XIV. Startup Procedure & Adjustment

  28
• HEAT ANTICIPATOR SETTING

  28
• DRAIN TRAP PRIMING

  28
• FURNACE OPERATION

  28
• GAS SUPPLY PRESSURE MEASUREMENT

  28
• GAS MANIFOLD PRESSURE MEASUREMENT AND ADJUSTMENT

  29
• GAS INPUT RATE MEASUREMENT (NATURAL GAS ONLY)

  29
• TEMPERATURE RISE

  30
• CIRCULATOR BLOWER SPEEDS

  30
• BLOWER HEAT OFF DELAY TIMINGS

  32
• XV. Normal Sequence of Operation

  32
• POWER UP

  32
• HEATING MODE

  32
• COOLING MODE

  32
• FAN ONLY MODE

  33
• XVI. Operational Checks

  33
• BURNER FLAME

  33
• XVII. Safety Circuit Description

  33
• GENERAL

  33
• INTEGRATED CONTROL MODULE

  33
• PRIMARY LIMIT

  33
• AUXILIARY LIMIT

  33
• ROLLOUT LIMIT

  33
• PRESSURE SWITCHES

  33
• FLAME SENSOR

  33
• XVIII. Troubleshooting

  33
• ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

  33
• DIAGNOSTIC CHART

  34
• RESETTING FROM LOCKOUT

  34
• XIX. Maintenance

  34
• ANNUAL INSPECTION

  34
• FILTERS

  34
• BURNERS

  34
• INDUCED DRAFT AND CIRCULATOR BLOWERS

  34
• CONDENSATE TRAP AND DRAIN SYSTEM (QUALIFIED SERVICER ONLY)

  35
• FLAME SENSOR (QUALIFIED SERVICER ONLY)

  35
• FLUE PASSAGES (QUALIFIED SERVICER ONLY)

  35
• XX. Internal Filter Removal

  35
• XXI. Before Leaving an Installation

  35
• XXII. Repair & Replacement Parts

  35
• Troubleshooting Chart

  37
• Wiring Diagram

  39