Benutzerhandbuch für Cisco CATALYST 6509E 9 SLOT 15U CHASSIS NO POWER SUPPLY NO FAN TRAY

Inhaltsverzeichnis

• Catalyst 6500 Series Switches Installation Guide

  1
  • Prefacexi

    5
• chapter 1

  5
  • Product Overview1-1

    5
• chapter 2

  6
  • Preparing for Installation2-1

    6
• chapter 3

  6
  • Installing the Switch3-1

    6
• chapter 4

  7
  • Removal and Replacement Procedures4-1

    7
• appendix A

  8
  • Power Supply SpecificationsA-1

    8
• appendix B

  8
  • Transceivers, Module Connectors, and Cable SpecificationsB-1

    8
• appendix C

  9
  • Repacking theSwitchC-1

    9
• appendix D

  9
  • Chassis and Module Power and Heat ValuesD-1

    9
• appendix E

  9
  • TroubleshootingE-1

    9
  • Index

    9
    • Preface

      11
  • Audience

    11
  • Organization

    11
  • Conventions

    12
    • Statement 1071—Warning Definition

      14
  • Related Documentation

    19
  • Obtaining Documentation

    20
    • Cisco.com

      20
    • Documentation DVD

      20
    • Ordering Documentation

      20
  • Documentation Feedback

    21
  • Cisco Product Security Overview

    21
    • Reporting Security Problems in Cisco Products

      21
  • Obtaining Technical Assistance

    22
    • Cisco Technical Support Website

      22
    • Submitting a Service Request

      22
    • Definitions of Service Request Severity

      23
  • Obtaining Additional Publications and Information

    23
    • Catalyst 6503 Switch

      26
      • Table1-1 Catalyst 6503 Switch Features

        26
      • Table1-2 Catalyst 6503 Switch Specifications

        29
        • Figure1-1 Catalyst 6503 Switch—Front View

          30
        • Figure1-2 Catalyst 6503 Switch—Rear View

          31
    • Catalyst 6503-E Switch

      32
      • Table1-3 Catalyst 6503-E Switch Features

        32
      • Table1-4 Catalyst 6503-E Switch Specifications

        34
        • Figure1-3 Catalyst 6503-E Switch—Front View

          36
        • Figure1-4 Catalyst 6503-E Switch—Rear View

          36
    • Catalyst 6504-E Switch

      37
      • Table1-5 Catalyst 6504-E Switch Features

        37
      • Table1-6 Catalyst 6504-E Switch Specifications

        38
        • Figure1-5 Catalyst 6504-E Switch—Front View

          40
        • Figure1-6 Catalyst 6504-E Switch—Rear View

          41
    • Catalyst 6506 Switch

      42
      • Table1-7 Catalyst 6506 Switch Features

        42
      • Table1-8 Catalyst 6506 Switch Specifications

        45
        • Figure1-7 Catalyst 6506 Switch

          47
    • Catalyst 6506-E Switch

      48
      • Table1-9 Catalyst 6506-E Switch Features

        48
      • Table1-10 Catalyst 6506-E Switch Specifications

        50
        • Figure1-8 Catalyst 6506-E Switch

          51
    • Catalyst 6509 Switch

      52
      • Table1-11 Catalyst 6509 Switch Features

        52
      • Table1-12 Catalyst 6509 Switch Specifications

        55
        • Figure1-9 Catalyst 6509 Switch

          57
    • Catalyst 6509-E Switch

      58
      • Table1-13 Catalyst 6509-E Switch Features

        58
      • Table1-14 Catalyst 6509-E Switch Specifications

        60
        • Figure1-10 Catalyst 6509-E Switch

          62
    • Catalyst 6509-NEB Switch

      63
      • Table1-15 Catalyst 6509-NEB Switch Features

        63
      • Table1-16 Catalyst 6509-NEB Switch Specifications

        66
        • Figure1-11 Catalyst 6509-NEB Switch

          68
    • Catalyst 6509-NEB-A Switch

      69
      • Table1-17 Catalyst 6509-NEB-A Switch Features

        69
      • Table1-18 Catalyst 6509-NEB-A Switch Specifications

        71
        • Figure1-12 Catalyst 6509-NEB-A Switch Chassis

          73
    • Catalyst 6513 Switch

      74
      • Table1-19 Catalyst 6513 Switch Features

        74
      • Table1-20 Catalyst 6513 Switch Specifications

        77
        • Figure1-13 Catalyst 6513 Switch

          79
    • Safety

      82
    • Site Requirements

      82
      • Temperature

        83
      • Humidity

        83
      • Altitude

        83
      • Dust and Particles

        84
      • Corrosion

        84
      • Electromagnetic and Radio Frequency Interference

        84
      • Shock and Vibration

        85
      • Power Source Interruptions

        85
      • System Grounding

        86
        • Table2-1 Gounding Practice Guidelines

          86
      • Preventing Electrostatic Discharge Damage

        87
        • Step1 Attach the ESD wrist strap to bare skin as follows:

          88
        • Step2 Grasp the spring or alligator clip on the ESD wrist strap and momentarily touch the clip t...

          88
        • Step3 Attach either the spring clip or the alligator clip to the ground lug screw as follows (Se...

          88
          • Figure2-1 Attaching the ESD Wrist Strap Clip to the System Ground Lug Screw

            89
      • Air Flow

        90
        • Table2-2 Catalyst 6500 Series Chassis Fan Tray Support

          91
        • Table2-3 Chassis Air Flow Requirements

          92
          • Figure2-2 Catalyst 6503 and Catalyst 6503-E Switch Internal Airflow

            92
          • Figure2-3 Catalyst 6504-E Switch Internal Airflow

            93
          • Figure2-4 Catalyst 6506 Switch Internal Airflow

            93
          • Figure2-5 Catalyst 6506-E Switch Internal Airflow

            94
          • Figure2-6 Catalyst 6509 Switch Internal Airflow

            95
          • Figure2-7 Catalyst 6509-E Switch Internal Airflow

            96
          • Figure2-8 Catalyst 6509-NEB Switch Internal Airflow

            97
          • Figure2-9 Catalyst 6509-NEB-A Switch Internal Airflow

            98
          • Figure2-10 Catalyst 6513 Switch Internal Airflow

            99
    • Power Requirements

      99
      • Power Connection Guidelines for AC-Powered Systems

        100
      • Power Connection Guidelines for DC-Powered Systems

        101
    • Cabling Requirements

      101
    • Site Preparation Checklist

      102
      • Table2-4 Site Planning Checklist

        102
    • Unpacking the Switch

      106
    • Installing the Rack-Mount Kit

      107
      • Table3-1 Rack-MountKit Contents Checklist

        107
      • Rack-Mounting Guidelines

        107
      • Required Tools

        109
      • Installing the Shelf Brackets and Crossbar Bracket

        109
        • Step1 Position one of the two shelf brackets in the rack as shown in Figure3-1.

          109
        • Step2 Secure the shelf bracket to the rack by using three 12-24 x 3/4-inch or 10-32 x 3/4-inch s...

          109
        • Step3 Repeat Steps 1 and 2 for the second shelf bracket. Make sure that the second shelf bracket...

          109
        • Step4 Attach the crossbar bracket to the back of the shelf brackets using two M3screws as shown...

          109
          • Figure3-1 Installing the ShelfBrackets

            109
          • Figure3-2 Attaching the Crossbar Bracket to the Shelf Brackets

            110
      • Installing the LBrackets and Cable Guides on the Catalyst6503 and the Catalyst6503-E Switches

        110
        • Step1 Position one of the brackets against the chassis side, and align the screw holes. (See Fig...

          110
        • Step2 Secure the bracket to the chassis with four M3 screws.

          110
        • Step3 Repeat Steps 1 and 2 for the other bracket.

          110
          • Figure3-3 Installing the L-Brackets on the Catalyst 6503 and the Catalyst6503-E Switch Chassis

            111
      • Installing the LBrackets and Cable Guides on the Catalyst6504-E Switch

        111
        • Step1 Position one of the brackets against the chassis side, and align the screw holes. (See Fig...

          111
        • Step2 Secure the bracket to the chassis with three M4 screws.

          111
        • Step3 Repeat Steps1 and 2 for the other bracket.

          111
        • Figure3-4 Installing the L-Brackets on the Catalyst6504-E Switch Chassis

          112
      • Installing the LBrackets and Cable Guides on the Catalyst6506 and Catalyst6506-E Switches

        112
        • Step1 Position the left (L) Lbracket and the optional cable guide (if desired) against the swit...

          112
        • Step2 Secure the Lbracket (and optional cable guide) to the switch chassis with four M3 screws.

          112
        • Step3 Repeat steps 1 and 2 for the right (R) Lbracket (and, if necessary, the optional cable gu...

          112
          • Figure3-5 Attaching L Brackets and CableGuides: Catalyst 6506 and Catalyst 6506-E Switch

            113
      • Installing the L Brackets and Cable Guides on the Catalyst 6509 and Catalyst6509-E Switches

        114
        • Step1 Position the left (L) Lbracket and the optional cable guide (if desired) against the swit...

          114
        • Step2 Secure the Lbracket (and optional cable guide) to the switch chassis with five M3 screws.

          114
        • Step3 Repeat steps 1 and 2 for the right (R) Lbracket (and, if necessary, the optional cable gu...

          114
          • Figure3-6 Attaching L Brackets and CableGuides: Catalyst 6509 Switch and Catalyst 6509-E Switch

            115
      • Installing the L Brackets and Cable Guides on the Catalyst6509-NEB Switch

        115
        • Step1 Position one of the Lbrackets against the switch chassis side, and align the screw holes....

          116
        • Step2 Secure the Lbracket to the switch chassis with five M4 screws.

          116
        • Step3 Repeat steps 1 and 2 for the other Lbracket. If you used the + set of holes for the first...

          116
        • Step1 Position the cable guide against the front of the chassis, and align the four screw holes ...

          116
        • Step2 Secure the cable guide with four M4 screws.

          116
          • Figure3-7 Attaching L Brackets and CableGuides: Catalyst 6509-NEB Switch

            116
      • Installing the L Brackets on the Catalyst6509-NEB-A Switch

        117
        • Step1 Remove the screws that secure the brackets to the chassis. (See Figure3-8.)

          117
          • Figure3-8 Brackets on Catalyst 6509-NEB-A Switch

            117
        • Step2 Position one of the brackets against the chassis side, and align the screw holes.

          117
        • Step3 Secure the bracket to the chassis with the screws that were removed in Step1.

          117
        • Step4 Repeat Step2 and Step3 for the other bracket.

          117
    • Installing the Switch Chassis in the Rack

      118
      • Step1 With a person standing at each side of the chassis, grasp the chassis handle with one hand...

        118
      • Step2 Position the chassis in the rack as follows:

        118
      • Step3 Align the mounting holes in the Lbracket with the mounting holes in the equipment rack.

        118
      • Step4 Align the cable guide bracket mounting holes with the mounting holes in the Lbracket and ...

        119
      • Step5 Install the eight or ten (four or five per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch scre...

        119
      • Step6 Use a tape measure and level to verify that the chassis is installed straight and level.

        119
        • Figure3-9 Installing the Catalyst6513 Switch in the Rack with the Optional Cable Guides

          119
    • Installing the Stabilizer Kit

      120
      • Table3-2 Stabilizer Kit Contents

        120
      • Step1 Have one person tilt and hold the chassis to one side.

        121
      • Step2 With the chassis tilted, attach the stabilizer bracket to the side of the chassis with the...

        121
      • Step3 Tilt the chassis to the other side.

        121
      • Step4 Attach the second stabilizer bracket to the other side of the chassis with eight M4 screws.

        121
      • Step5 Lower the chassis so that it rests on both stabilizer brackets.

        121
        • Figure3-10 Installing the Stabilizer Brackets

          121
    • Installing the Cable Management System (Catalyst6509-NEB-A Switch Only)

      122
      • Step1 Place the cable management system against the chassis, as shown in Figure3-11, and tighte...

        122
      • Step2 Assure that the hinge is flat against the chassis, and install four 6x32 screws to secure ...

        122
        • Figure3-11 Installing the Cable Management System

          122
      • Step3 Loosen the two captive installation screws on the front panel. (See Figure3-12.)

        123
        • Figure3-12 Removing the Front Panel

          123
      • Step4 Remove the front panel, and set it aside.

        123
      • Step5 Attach the interface cables to the modules, and route the cables through the cable guide.

        123
      • Step6 Install the front panel by hooking the top of the front panel over the cable guide.

        123
      • Step7 Tighten the two captive installation screws. (See Figure3-12.)

        123
      • Replacing the Cable Guide

        124
        • Step1 Loosen the two captive installation screws on the front panel. (See Figure3-13.)

          124
          • Figure3-13 Removing the Front Panel

            124
        • Step2 Remove the front panel, and set it aside.

          124
        • Step3 Remove the two screws that secure the cable guide to the back panel, and remove the cable ...

          124
          • Figure3-14 Removing the Cable Guide

            124
        • Step4 Install the standard cable guide to the back panel by hooking the lip of the cable guide t...

          125
        • Step5 Install the two screws to secure the cable guide to the back plate. (See Figure3-14.)

          125
        • Step6 Attach the interface cables to the modules, and route the cables through the cable guide.

          125
        • Step7 Install the front panel by hooking the top of the front panel over the cable guide.

          125
        • Step8 Tighten the two captive installation screws. (See Figure3-15.)

          125
          • Figure3-15 Front Panel Installation

            125
    • Establishing the System Ground

      126
      • Required Tools and Equipment

        126
      • Connecting the System Ground

        127
        • Step1 Use a wire-stripping tool to remove approximately 0.75inch (19mm) of the covering from t...

          127
        • Step2 Insert the stripped end of the grounding wire into the open end of the grounding lug.

          127
        • Step3 Crimp the grounding wire in the barrel of the grounding lug. Verify that the ground wire i...

          127
        • Step4 Locate and remove the adhesive label from the system grounding pad on the switch. The loca...

          127
        • Step5 Place the grounding wire lug against the grounding pad, making sure that there is solid me...

          127
        • Step6 Secure the grounding lug to the chassis with two M4 screws. Ensure that the grounding lug ...

          127
        • Step7 Prepare the other end of the grounding wire, and connect it to an appropriate grounding po...

          127
          • Figure3-16 System Ground Location (Catalyst 6503 and Catalyst 6503-E Chassis)

            128
          • Figure3-17 System Ground Location (Catalyst 6504-E Chassis)

            128
          • Figure3-18 System Ground Location (Catalyst 6506, Catalyst 6509, and Catalyst 6509-NEB Chassis)

            129
          • Figure3-19 System Ground Location (Catalyst 6506-E, Catalyst 6509-E, and Catalyst 6513 Chassis)

            130
          • Figure3-20 System Ground Location (Catalyst 6509-NEB-A)

            131
    • Installing the Power Supplies in the Switch Chassis

      132
    • Attaching the Interface Cables

      132
      • Connecting the Supervisor Engine Console Port

        132
        • Figure3-21 Supervisor Engine Console Port Connector

          132
        • Step1 Place the console port mode switch in the in position (factory default).

          133
        • Step2 Connect to the port using the RJ-45-to-RJ-45 cable and RJ-45-to-DB-25 DTE adapter or RJ-45...

          133
        • Step3 Position the cable in the cable guide (if installed). Make sure there are no sharp bends i...

          133
        • Step4 Check the terminal documentation to determine the baud rate. The baud rate of the terminal...

          133
        • Step1 Place the console port mode switch in the out position.

          133
        • Step2 Connect to the port using the Supervisor Engine III cable and the appropriate adapter for ...

          133
        • Step3 Position the cable in the cable guide (if installed). Make sure there are no sharp bends i...

          133
        • Step4 Check the terminal documentation to determine the baud rate. The baud rate of the terminal...

          133
        • Step1 Place the console port mode switch in the in position.

          133
        • Step2 Connect to the port using the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-25 DCE ada...

          133
        • Step3 Position the cable in the cable guide (if installed). Make sure there are no sharp bends i...

          133
      • Connecting the Supervisor Engine Uplink Ports

        134
        • Supervisor Engine 1 and Supervisor Engine 2 Uplink Ports

          134
          • Step1 Attach an ESD-preventive wrist strap to your wrist and to the ESD ground connector or a ba...

            134
          • Step2 Remove the GBIC transceiver module from its protective packaging.

            134
          • Step3 Check the label on the GBIC transceiver body to verify that you have the correct model for...

            134
          • Step4 Find the transmit (TX) and receive (RX) markings that identify the top side of the GBIC tr...

            134
          • Step5 Position the GBIC transceiver in front of the socket opening.

            134
          • Step6 Insert the GBIC transceiver into the socket until you feel the GBIC transceiver module con...

            135
          • Step7 Remove the dust plugs from the network interface cable SC connectors. Save the dust plugs ...

            135
          • Step8 Inspect and clean the fiber-optic end-faces on the SC connector. (See the Tip below for a ...

            135
          • Step9 Remove the dust plugs from the GBIC transceiver optical bores.

            135
          • Step10 Immediately attach the network interface cable SC connector to the GBIC transceiver.

            135
          • Step11 To connect 1000BASE-T GBIC transceivers to a copper network, perform the following substeps:

            135
          • Step12 Observe the port status LED:

            136
            • Figure3-22 Connecting the Supervisor Engine Uplink Ports

              136
        • Supervisor Engine 32 and Supervisor Engine 720 Uplink Ports

          136
          • Step1 Attach an ESD-preventive wrist strap to your wrist and to the ESD ground connector or a ba...

            137
          • Step2 Remove the SFP transceiver module from its protective packaging.

            137
          • Step3 Check the label on the SFP transceiver body to verify that you have the correct model for ...

            137
          • Step4 Find the transmit (TX) and receive (RX) markings that identify the top side of the SFP tra...

            137
          • Step5 Position the SFP transceiver in front of the socket opening.

            137
          • Step6 Insert the SFP transceiver into the socket until you feel the SFP transceiver module conne...

            137
          • Step7 Remove the dust plugs from the network interface cable LC connectors. Save the dust plugs ...

            137
          • Step8 Inspect and clean the LC connector’s fiber-optic end-faces. (Refer to the Tip below for a ...

            137
          • Step9 Remove the dust plugs from the SFP transceiver optical bores.

            138
          • Step10 Immediately attach the network interface cable LC connector to the SFP transceiver.

            138
          • Step11 To connect 1000BASE-T SFP transceivers to a copper network, perform the following substeps:

            138
          • Step12 Observe the port status LED:

            138
            • Figure3-23 Supervisor Engine 720 SFP Uplink Port

              138
    • Verifying Switch Chassis Installation

      139
      • Step1 Verify that the ejector levers of each module are fully closed (parallel to the faceplate)...

        139
      • Step2 Check the captive installation screws of each module, the power supply, and the fan assemb...

        139
      • Step3 Verify that all empty module slots have blank faceplates (WS-X6K-SLOT-CVR) installed and t...

        139
      • Step4 Turn on the power supply switches to power up the system. During the power-up sequence, th...

        139
      • Step5 (Optional) Additional system diagnostic tests are available. These tests allow you to perf...

        139
      • Online Diagnostics

        140
    • Removing and Installing the AC-Input Power Supplies

      142
      • Table4-1 Catalyst 6500 Series AC-Input Power Supplies Removal and Installation Procedures

        142
      • Removing and Installing the 950W and 1400W AC-Input Power Supplies

        142
        • Required Tools

          142
        • Removing a 950W or 1400W AC-Input Power Supply

          143
          • Step1 Turn the power switch to the Off (0) position on the PEM for the power supply that you are...

            143
          • Step2 Disconnect the power cord from the power source. Do not touch the metal prongs on the powe...

            143
          • Step3 Remove the power cord from the power connection on the PEM. Do not touch the metal prongs ...

            143
          • Step4 Loosen the captive installation screws on the power supply. (See Figure4-2 for the Cataly...

            143
          • Step5 Grasp the power supply handle with one hand, and slide the power supply part of the way ou...

            143
          • Step6 If the power supply bay is to remain empty, install a blank power supply filler plate (Cis...

            143
            • Figure4-1 Catalyst 6503 and Catalyst6503-E Switches—PEM Location

              144
            • Figure4-2 Power Supply Captive Installation Screws

              144
            • Figure4-3 Handling an AC-Input Power Supply

              145
        • Installing a 950W or 1400W AC-Input Power Supply

          145
          • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

            145
          • Step2 If necessary, remove the blank power supply filler plate from the chassis power supply bay...

            145
          • Step3 Grasp the power supply handle with one hand. Place your other hand underneath the power su...

            145
          • Step4 Securely tighten the power supply captive installation screws. (See Figure4-2 for the Cat...

            145
          • Step5 At the front of the chassis, plug the power cord into the PEM.

            145
          • Step6 Connect the other end of the power cord to an AC-input power source.

            146
          • Step7 Turn the PEM power switch to the On (|) position.

            146
          • Step8 Verify the power supply operation by checking that the power supply LEDs are in the follow...

            146
      • Removing and Installing the 2700W AC-Input Power Supply

        146
        • Required Tools

          146
        • Removing a 2700W AC-Input Power Supply

          147
          • Step1 Turn the power switch to the Off (0) position on the power supply you are removing.

            147
          • Step2 Disconnect the power cord from the power source. Do not touch the metal prongs on the powe...

            147
          • Step3 Remove the power cord from the power connection on the power supply.

            147
          • Step4 Loosen the captive installation screws on the power supply. (See Figure4-4.)

            147
            • Figure4-4 2700W AC-Input Power Supply Captive Installation Screws

              147
          • Step5 Grasp both power supply handles, as shown in Figure4-5, and slide the power supply comple...

            147
            • Figure4-5 Handling a 2700W AC-Input Power Supply

              148
          • Step6 If the power supply bay is to remain empty, install a blank power supply filler plate (Cis...

            148
        • Installing a 2700W AC-Input Power Supply

          148
          • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

            148
          • Step2 If necessary, remove the blank power supply filler plate from the chassis power supply bay...

            148
          • Step3 Verify that the power switch on the power supply is in the Off (0) position.

            148
          • Step4 Grasp both power supply handles. (See Figure4-5.) Slide the power supply into the power s...

            148
          • Step5 Securely tighten the power supply captive installation screws.

            148
          • Step6 Plug the power cord into the power supply AC-in receptacle.

            149
          • Step7 Connect the other end of the power cord to the AC-input power source.

            149
          • Step8 Turn the switch on the power supply to the On (|) position.

            149
          • Step9 Verify power supply operation by checking that the power supply LEDs are in the following ...

            149
      • Removing and Installing the 1000W, 1300W, 2500W, 3000W, 4000W, and 6000W AC-Input Power Sup...

        149
        • Required Tools

          149
        • Removing the 1000W, 1300W, 2500W, 3000W, 4000W, and 6000W AC-Input Power Supplies

          150
          • Step1 Turn the power switch to the Off (0) position on the power supply that you are removing. (...

            150
          • Step2 Disconnect the power cord from the power source.

            150
          • Step3 Loosen the screw on the cable retention device, and disconnect the power cord from the pow...

            150
          • Step4 Loosen the captive installation screw. (See Figure4-6.)

            150
            • Figure4-6 AC-InputPower Supply Front Panel

              150
          • Step5 Grasp the power supply handle with one hand, and slide the power supply part of the way ou...

            150
          • Step6 If the power supply bay is to remain empty, install a blank faceplate (Cisco partnumber7...

            150
            • Figure4-7 Handling an AC-Input Power Supply

              151
        • Installing the 1000W, 1300W, 2500W, 3000W, 4000W, and 6000W AC-Input Power Supplies

          151
          • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

            151
          • Step2 If necessary, remove the blank faceplate (Cisco partnumber700-03104-01) from the chassis...

            151
          • Step3 Verify that the power switch is in the Off (0) position on the power supply that you are i...

            151
          • Step4 Grasp the power supply handle with one hand. Place your other hand underneath the power su...

            152
          • Step5 Tighten the power supply captive installation screw. (SeeFigure4-6.)

            152
          • Step6 Plug the power cord into the power supply, and tighten the screw on the cable retention de...

            152
          • Step7 Connect the other end of the power cord to an AC-input power source.

            152
          • Step8 Turn the power switch to the On (|) position on the power supply. Switching the power swit...

            152
          • Step9 Verify the power supply operation by ensuring that the power supply front panel LEDs are i...

            152
    • Removing and Installing the DC-Input Power Supplies

      153
      • Removing and Installing a 950W DC-Input Power Supply

        153
        • Tools Required

          153
        • Removing a 950W DC-Input Power Supply

          154
          • Step1 Identify which PEM is connected to the power supply you are removing (PEM1 or PEM2). Ver...

            154
          • Step2 Loosen the captive installation screws on the power supply. (See Figure4-9.)

            154
          • Step3 Grasp the power supply handle with one hand, and slide the power supply part of the way ou...

            154
          • Step4 If the power supply bay is to remain empty, install a blank power supply filler plate (Cis...

            154
            • Figure4-8 Catalyst 6503 Switch—DC-Input PEM Location

              154
            • Figure4-9 950W DC-Input Power Supply Captive Installation Screws

              155
            • Figure4-10 Catalyst 6503 Switch—Handling a DC-Input Power Supply

              155
        • Installing a 950W DC-Input Power Supply

          156
          • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

            156
          • Step2 Verify that power is off to the DC circuit connected to the DC PEM for the power supply th...

            156
          • Step3 Grasp the power supply handle with one hand. Place your other hand underneath the power su...

            156
          • Step4 Tighten the power supply captive installation screws. (See Figure4-9.)

            156
          • Step5 Verify that all connections to the DC PEM are secure.

            156
          • Step6 Remove any safety flags, lockout devices, or tape from the circuit breaker switch handle, ...

            156
          • Step7 Verify the power supply operation by ensuring that the power supply front panel LEDs are i...

            156
      • Removing and Installing a 1300W or 2500W DC-Input Power Supply

        157
        • Required Tools

          157
        • Removing a 1300W or 2500W DC-Input Power Supply

          157
          • Step1 Verify that power is off to the DC circuit on the power supply that you are removing. As a...

            157
          • Step2 Turn the power switch to the Off (0) position on the power supply that you are removing. (...

            157
          • Step3 Remove the two screws securing the terminal block cover, and slide the cover off the termi...

            157
          • Step4 Disconnect the DC-input wires from the terminal block (see Figure4-13 for the 1300W DC p...

            158
          • Step5 Loosen the captive installation screw on the power supply. (See Figure4-13 for the 1300W...

            158
          • Step6 Grasp the power supply handle with one hand, and slide the power supply halfway out of the...

            158
          • Step7 If the power supply bay is to remain empty, install a blank faceplate (Ciscopartnumber7...

            158
            • Figure4-11 DC-InputPower Supply Front Panel (WS-CDC-1300W)

              158
            • Figure4-12 DC-InputPower Supply Front Panel (WS-CDC-2500W)

              159
            • Figure4-13 DC-Input Wire Connections on the Terminal Block (WS-CDC-1300W)

              159
            • Figure4-14 DC-Input Wire Connections on the Terminal Block (WS-CDC-2500W)

              160
            • Figure4-15 Handling a DC-Input Power Supply

              161
        • Installing a 1300W or 2500W DC-Input Power Supply

          162
          • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

            162
          • Step2 Verify that power is off to the DC circuit on the power supply that you are installing. As...

            162
          • Step3 Verify that the power switch is in the Off (0) position on the power supply that you are i...

            162
          • Step4 Grasp the power supply handle with one hand, and place your other hand underneath the powe...

            162
          • Step5 Tighten the power supply captive installation screw. (See Figure4-11 for the 1300W DC po...

            162
          • Step6 Remove the two screws securing the terminal block cover, and slide the cover off of the te...

            162
          • Step7 Attach the appropriate lugs to the DC-input wires. The maximum width of a lug is 0.300 inc...

            163
          • Step8 Connect the DC-input wires to the terminal block (see Figure4-16 for the 1300W DC power ...

            163
          • Step9 After ensuring that all wire connections are secure, reinstall the terminal block cover.

            163
          • Step10 Remove any safety flag and lockout devices or any tape from the circuit breaker switch ha...

            163
          • Step11 Turn the power switch to the On (|) position on the power supply. Turning on the power sw...

            163
          • Step12 Verify the power supply operation by ensuring that the power supply front panel LEDs are ...

            163
            • Figure4-16 DC-InputPower Supply Connectors (WS-CDC-1300W)

              164
            • Figure4-17 DC-InputPower Supply Connectors (WS-CDC-2500W)

              164
      • Removing and Installing the 2700W DC-Input Power Supply

        165
        • Required Tools

          165
        • Removing a 2700W DC-Input Power Supply

          165
          • Step1 Verify that power is off to the DC circuit on the power supply that you are removing. As a...

            165
          • Step2 Remove the four screws securing the terminal block cover, and slide the cover off the term...

            165
            • Figure4-18 DC-Input Front Panel for 2700-W DC-Input Power Supply

              166
          • Step3 Remove the two screws securing each of the cable holder covers, and remove the cable holde...

            166
          • Step4 Disconnect the DC-input wires from the terminal block (Figure4-19) in this order:

            166
          • Step5 Remove the two tie-wraps from the ground cable. If there is a long cable tie-wrap securing...

            166
          • Step6 Loosen the captive installation screws on the power supply. (See Figure4-18.)

            166
          • Step7 Grasp both power supply handles, as shown in Figure4-19, and slide the power supply compl...

            167
          • Figure4-19 Handling a DC-Input Power Supply

            167
            • Step8 If the power supply bay is to remain empty, install a blank power supply filler plate (Cis...

              167
        • Installing a 2700W DC-Input Power Supply

          167
          • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

            167
          • Step2 Remove the plastic bag attached to the front panel and put aside. This bag contains two pl...

            167
          • Step3 Verify that power is off to the DC circuit on the power supply that you are installing. As...

            167
          • Figure4-20 Handling the Power Supply

            168
            • Step4 Tighten the power supply captive installation screws. (See Figure4-21.)

              168
              • Figure4-21 Power Supply Captive Installation Screws

                168
              • Figure4-22 DC-Input Front Panel for 2700-W DC-Input Power Supply

                169
            • Step5 Remove the four screws securing the terminal block cover, and slide the cover off of the t...

              169
            • Step6 Attach the appropriate lugs to the DC-input wires. The maximum width of a lug is 0.300 inc...

              169
            • Step7 Connect the DC-input wires to the 2700W power supply terminal block (Figure4-22) in this...

              170
            • Step8 Secure the ground cable to the cable holder with the two cable-ties.

              170
            • Step9 Retrieve the cable holder covers from the plastic bag and attach to the front panel at the...

              170
            • Step10 Secure the terminal block cover using four screws and the terminal block barriers with tw...

              170
            • Step11 Turn on the DC inputs and verify power supply operation by checking that the power supply...

              170
              • Figure4-23 DC-Input Wires on Left Side

                170
      • Removing and Installing a 4000W DC-Input Power Supply

        171
        • Required Tools

          171
        • Removing a 4000W DC-Input Power Supply

          171
          • Step1 Verify that power is off to the DC circuit connected to the DC-input power supply that you...

            171
          • Step2 Turn the power switch to the Off (0) position on the power supply that you are removing. (...

            171
            • Figure4-24 DC-Input Front Panel for 4000-W DC-Input Power Supply

              172
          • Step3 Remove the two screws securing the outer terminal block cover, and remove the cover from t...

            173
          • Step4 Remove the two screws securing the left inner terminal block cover, remove the cover, and ...

            173
          • Step5 Remove the plastic insulator from over the terminal area. (See Figure4-25.)

            173
          • Step6 Disconnect the DC-input wires from the terminal block in this order:

            173
            • Figure4-25 DC-Input Wire Connections for 4000-W DC-Input Power Supply

              173
          • Step7 Loosen the captive installation screw on the power supply. (See Figure4-25.)

            174
          • Step8 Grasp the power supply handle with one hand, and slide the power supply part of the way ou...

            174
            • Figure4-26 Handling a 4000W DC-Input Power Supply

              174
          • Step9 If the power supply bay is to remain empty, install a blank power supply filler plate (Cis...

            174
        • Installing a 4000W DC-Input Power Supply

          175
          • Table4-2 4000W DC-Input Power Supply Installation Options

            175
          • Figure4-27 4000W DC-Input Power Supply Front Panel

            176
          • Installing the 4000W Power Supply (Wiring for 2700W Operation; Left Power Bay)

            177
            • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

              177
            • Step2 Verify that power is off to the DC circuit that is connected to the power supply that you ...

              177
            • Step3 Prepare the source DC-input power cables by attaching the appropriately sized lugs.

              177
              • Figure4-28 DC Power Cable Lug

                177
            • Step4 Grasp the power supply handle with one hand, and place your other hand underneath the powe...

              178
              • Figure4-29 Handling a 4000W DC-Input Power Supply

                178
            • Step5 Tighten the power supply captive installation screws. (See Figure4-27.)

              178
            • Step6 Remove the two screws that secure the outer terminal block cover, and remove the cover fro...

              178
            • Step7 Remove the two screws that secure the left inner terminal block cover, remove the cover, a...

              178
            • Step8 Place both plastic insulators over the terminal areas, aligning the circular holes in insu...

              178
            • Step9 Wrap the large perforated flaps around each pair of conductors, inserting each locking tab...

              179
            • Step10 From the left side of the power supply, connect the DC-input wires to the left power supp...

              179
              • Figure4-30 DC-Input Wire Connections for 2700W Operation (Left-Side Power Bay)

                179
            • Step11 From the left side of the power supply, connect the DC-input wires to TB1 in this order:

              179
            • Step12 Position and secure the left and the right inner terminal block covers.

              180
            • Step13 Secure outer terminal block cover.

              180
            • Step14 If you are installing a second power supply operating at 2700W in the right-side power s...

              180
            • Step15 After you confirm that all installation steps are completed correctly, remove any safety ...

              180
            • Step16 Turn the power switch to the On (|) position on the power supply. Turning on the power sw...

              180
            • Step17 Verify the power supply operation by ensuring that the power supply front panel LEDs are ...

              180
          • Installing the 4000W Power Supply (Wiring for 2700W Operation; Right Power Bay)

            180
            • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

              180
            • Step2 Verify that power is off to the DC circuit that is connected to the power supply that you ...

              180
            • Step3 Prepare the source DC-input power cables by attaching the appropriately sized lugs.

              180
              • Figure4-31 DC Power Cable Lug

                181
            • Step4 Grasp the power supply handle with one hand, and place your other hand underneath the powe...

              181
              • Figure4-32 Handling a 4000W DC-Input Power Supply

                181
            • Step5 Tighten the power supply captive installation screws.

              181
            • Step6 Remove the two screws that secure the outer terminal block cover, and remove the cover fro...

              182
            • Step7 Remove the two screws that secure the left inner terminal block cover, remove the cover, a...

              182
            • Step8 Place both plastic insulators over the terminal areas, aligning the circular holes in insu...

              182
            • Step9 Wrap the large perforated flaps around each pair of conductors, inserting each locking tab...

              182
            • Step10 From the right side of the power supply, connect the DC-input wires to the left power sup...

              182
              • Figure4-33 DC-Input Wire Connections for 2700W Operation (Right-Side Power Bay)

                183
            • Step11 Position and secure the left and right inner terminal block covers.

              183
            • Step12 Using the cable tie provided, place the cable tie through the slot at the top of the righ...

              183
            • Step13 Secure outer terminal block cover.

              183
            • Step14 After you confirm that all installation steps are completed correctly, remove any safety ...

              183
            • Step15 Turn the power switch to the On (|) position on the power supply. Turning on the power sw...

              183
            • Step16 Verify the power supply operation by ensuring that the power supply front panel LEDs are ...

              183
          • Installing the 4000W Power Supply (Wiring for 4000W Operation; Left Power Bay)

            184
            • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

              184
            • Step2 Verify that power is off to the DC circuit that is connected to the power supply that you ...

              184
            • Step3 Prepare the source DC-input power cables by attaching the appropriately sized lugs.

              184
              • Figure4-34 DC Power Cable Lug

                184
            • Step4 Grasp the power supply handle with one hand, and place your other hand underneath the powe...

              185
              • Figure4-35 Handling a 4000W DC-Input Power Supply

                185
            • Step5 Tighten the power supply captive installation screws.

              185
            • Step6 Remove the two screws that secure the outer terminal block cover, and remove the cover fro...

              185
            • Step7 Remove the two screws that secure the left inner terminal block cover, remove the cover, a...

              185
            • Step8 Place both plastic insulators over the terminal areas, aligning the circular holes in insu...

              185
            • Step9 Wrap the large perforated flaps around each pair of conductors, inserting each locking tab...

              185
            • Step10 From the left side of the power supply, connect the DC-input wires to the left power supp...

              186
            • Step11 From the left side of the power supply, connect the DC-input wires to the right power sup...

              186
              • Figure4-36 DC-Input Wire Connections for 4000W Operation (Left-Side Power Bay)

                186
            • Step12 Using the cable tie provided, place the cable tie through the slot at the top of the left...

              187
            • Step13 Secure the outer block cover.

              187
            • Step14 Position and secure the left and right inner terminal block covers.

              187
            • Step15 Secure the outer terminal block cover.

              187
            • Step16 If you are installing a second power supply that operates at 4000W in the right side pow...

              187
            • Step17 After you confirm that all installation steps are completed correctly, remove any safety ...

              187
            • Step18 Turn the power switch to the On (|) position on the power supply. Turning on the power sw...

              187
            • Step19 Verify the power supply operation by ensuring that the power supply front panel LEDs are ...

              187
          • Installing the 4000W Power Supply (Wiring for 4000W Operation; Right Power Bay)

            187
            • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

              187
            • Step2 Verify that power is off to the DC circuit that is connected to the power supply that you ...

              187
            • Step3 Prepare the source DC-input power cables by attaching the appropriately sized lugs.

              188
              • Figure4-37 DC Power Cable Lug

                188
            • Step4 Grasp the power supply handle with one hand, and place your other hand underneath the powe...

              188
              • Figure4-38 Handling a 4000W DC-Input Power Supply

                188
            • Step5 Tighten the power supply captive installation screws.

              189
            • Step6 Remove the two screws that secure the outer terminal block cover, and remove the cover fro...

              189
            • Step7 Remove the two screws that secure the left inner terminal block cover, remove the cover, a...

              189
            • Step8 Place both plastic insulators over the terminal areas, aligning the circular holes in insu...

              189
            • Step9 Wrap the large perforated flaps around each pair of conductors, inserting each locking tab...

              189
            • Step10 From the right side of the power supply, connect the DC-input wires to the right power su...

              189
            • Step11 From the right side of the power supply, connect the DC-input wires to the left power sup...

              189
              • Figure4-39 DC-Input Wire Connections for 4000W Operation (Right-Side Power Bay)

                190
            • Step12 Using the cable tie provided, place the cable tie through the slot at the top of the righ...

              190
            • Step13 Position and secure the left and right inner terminal block covers.

              190
            • Step14 Secure the outer block cover.

              190
            • Step15 After you confirm that all installation steps are completed correctly, remove any safety ...

              190
            • Step16 Turn the power switch to the On (|) position on the power supply. Turning on the power sw...

              191
            • Step17 Verify the power supply operation by ensuring that the power supply front panel LEDs are ...

              191
    • Removing and Installing the Power Entry Modules (PEMs)

      191
      • Figure4-40 Catalyst 6503—PEM Location

        191
      • Figure4-41 Catalyst 6503 Switch—Power Supply Location

        192
      • Required Tools

        192
      • Removing the AC-Input PEM

        192
        • Step1 Turn the power switch to the Off (0) position on the PEM that you are removing. (SeeFigur...

          192
        • Step2 Disconnect the power cord from the power source. Do not touch the metal prongs on the powe...

          192
        • Step3 Remove the power cord from the power connection on the PEM. Do not touch the metal prongs ...

          192
        • Step4 Loosen the captive installation screws. (See Figure4-42.)

          192
        • Step5 Grasp the PEM with one hand, and slide it part of the way out of the chassis. Place your o...

          192
        • Step6 If the PEM bay is to remain empty, install a blank PEM filler plate (Cisco partnumber800...

          192
          • Figure4-42 AC-Input PEM (PEM-20A-AC+ Shown)

            193
          • Figure4-43 Handling a PEM

            193
      • Installing the AC-Input PEM

        193
        • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

          193
        • Step2 If necessary, remove the blank PEM filler plate (Cisco partnumber 800-16719-01) from the ...

          193
        • Step3 Grasp the PEM with one hand. Place your other hand underneath the PEM, as shown in Figure...

          193
        • Step4 Tighten the PEM captive installation screws. (SeeFigure4-42.)

          193
        • Step5 Plug the power cord into the PEM. (See AppendixA for a list of supported AC power cords.)

          194
        • Step6 Connect the other end of the power cord to an AC-input power source.

          194
        • Step7 Turn the power switch to the On (|) position on the PEM.

          194
      • Removing the DC-Input PEM

        194
        • Step1 Verify that power is off to the DC circuit for the PEM that you are removing. As an added ...

          194
        • Step2 Loosen the captive installation screws on the PEM. (See Figure4-44.)

          194
        • Step3 Slide the PEM part way out of the chassis so that you have access to the PEM terminal bloc...

          194
        • Step4 Disconnect the DC-input wires from the PEM terminal block in this order:

          194
        • Step5 Grasp the PEM with one hand, and place your other hand underneath the PEM, as shown in Fig...

          195
        • Step6 If the PEM bay is to remain empty, install a blank PEM filler plate (Cisco partnumber800...

          195
          • Figure4-44 DC-Input PEM

            195
          • Figure4-45 DC-Input PEM Terminal Block Screws

            195
          • Figure4-46 Handling a DC-Input PEM

            195
      • Installing the DC-Input PEM

        196
        • Step1 Ensure that the system (earth) ground connection has been made. For ground connection inst...

          196
        • Step2 Verify that power is off to the DC circuit for the PEM that you are installing. As an adde...

          196
        • Step3 Install the PEM part way in the chassis so that you still have access to the PEM terminal ...

          196
        • Step4 Connect the DC-input wires to the terminal block in this order:

          196
        • Step5 After ensuring that all wire connections are secure, install the PEM in the bay.

          196
        • Step6 Tighten the power supply captive installation screws. (SeeFigure4-48.)

          196
        • Step7 Remove the safety flag, lockout devices, or tape from the circuit breaker switch handle, a...

          196
        • Step8 Verify the power supply operation by ensuring that the power supply front panel LEDs are i...

          196
          • Figure4-47 DC-Input PEM Terminal Block Screws

            197
          • Figure4-48 DC-InputPEM

            197
    • Removing and Installing the Fan Assembly

      197
      • Required Tools

        197
      • Removing the Fan Assembly

        197
        • Step1 Locate the fan assembly as follows:

          198
        • Step2 Loosen the two captive installation screws by turning them counterclockwise.

          198
        • Step3 Grasp the fan assembly with both hands, and pull it outward; rock it gently, if necessary,...

          198
        • Step4 Pull the fan assembly clear of the chassis, and put it in a safe place.

          198
          • Figure4-49 Fan Assembly: Catalyst 6503 and Catalyst 6503-E Switches

            199
          • Figure4-50 Fan Assembly: Catalyst 6504-E Switch

            199
          • Figure4-51 Fan Assembly: Catalyst 6506 and Catalyst 6506-E Switches

            200
          • Figure4-52 Fan Assembly: Catalyst 6509 and Catalyst 6509-E Switches

            201
          • Figure4-53 Fan Assembly: Catalyst 6509-NEB Switch

            202
          • Figure4-54 Fan Assembly: Catalyst 6509-NEB-A Switch

            203
          • Figure4-55 Accessing the Fan Trays on the Catalyst 6509-NEB-A Switch

            204
          • Figure4-56 Fan Assembly: Catalyst 6513 Switch

            204
      • Installing the Fan Assembly

        205
        • Step1 Hold the fan assembly with the fans facing to the right and the FAN STATUS LED at the bottom.

          205
        • Step2 Place the fan assembly into the front chassis cavity so that it rests on the chassis, and ...

          205
        • Step3 Push the fan assembly into the chassis until the power connector seats in the backplane an...

          205
        • Step4 Tighten the captive installation screws.

          205
      • Checking the Installation

        205
        • Step1 Listen for the fans; you should immediately hear them operating. If you do not hear them, ...

          205
        • Step2 Verify that the FAN STATUS LED is green. If the LED is red, one or more of the fans are fa...

          205
        • Step3 If after several attempts the fans do not operate or if you experience trouble with the in...

          205
    • Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch (Optional)

      206
      • Table4-3 Air Filter Part Numbers

        206
      • Step1 Remove the intake panel by unscrewing four thumbscrews. (See Figure4-57.)

        206
        • Figure4-57 Removing the Intake Panel

          206
      • Step2 Install the new intake panel by tightening four thumbscrews. (See Figure4-58.)

        206
        • Figure4-58 Installing the New Intake Panel

          207
      • Step3 Remove the inner filter retainer from the filter cage assembly by depressing the thumb loo...

        207
        • Figure4-59 Removing the Inner Filter Retainer

          208
      • Step4 Place the foam filter over the filter retainer. (See Figure4-60.)

        208
      • Step5 Slide the retainer and filter into the cage assembly.

        208
        • Figure4-60 Placing the Foam Filter Over the Filter Retainer

          209
      • Step6 Install the filter assembly with the tabs facing the floor, as follows:

        209
        • Figure4-61 Installing the Filter Assembly

          210
          • A

            211
            • Power Supply Specifications

              211
              • TableA-1 Catalyst 6500 Series Power Supplies

                211
    • Power Supply Compatibility Matrix

      212
      • TableA-2 Catalyst6500 Series Switch Supported Power Supply Configurations

        212
    • 950W AC-Input and DC-Input Power Supplies

      214
      • FigureA-1 950W AC- and DC-Input Power Supplies

        214
      • FigureA-2 950W AC-Input PEM (PEM-15A-AC)

        214
      • FigureA-3 DC Power Entry Module (PEM)

        215
      • 950W Power Supply Specifications

        215
        • TableA-3 950 W AC-Input and DC-Input Power Supplies Specifications

          215
      • 950W Power Supply AC Power Cords

        218
        • TableA-4 950W AC-Input Power Supply Power Cords

          218
    • 1000W AC-Input Power Supply

      219
      • FigureA-4 1000W AC-Input Power Supply

        219
      • 1000W Power Supply Specifications

        220
        • TableA-5 1000W Power Supply Specifications

          220
      • 1000W Power Supply AC Power Cords

        222
        • TableA-6 1000W AC-Input Power Supply Power Cords

          222
    • 1300W AC-Input and DC-Input Power Supplies

      223
      • FigureA-5 1300W AC-input Power Supply

        223
      • FigureA-6 1300W DC-Input Power Supply

        223
      • 1300W Power Supply Specifications

        224
        • TableA-7 1300W AC-Input and DC-Input Power Supplies Specifications

          224
      • 1300W Power Supply AC Power Cords

        227
        • TableA-8 1300W Power Supply AC Power Cords

          227
    • 1400W AC-Input Power Supply

      228
      • FigureA-7 1400W AC-Input Power Supply (PWR-1400-AC)

        228
      • FigureA-8 1400W AC-Input PEM (PEM-20A-AC+)

        228
      • 1400W Power Supply Specifications

        229
        • TableA-9 1400W Power Supply Specifications

          229
      • 1400W Power Supply AC Power Cords

        230
        • TableA-10 1400W Power Supply AC Power Cords

          230
    • 2500W AC-Input and DC-Input Power Supplies

      232
      • FigureA-9 2500W AC-Input Power Supply

        232
      • FigureA-10 2500W DC-input Power Supply

        233
      • 2500W Power Supply Specifications

        233
        • TableA-11 2500W Power Supply Specifications

          233
      • 2500W Power Supply AC Power Cords

        237
        • TableA-12 2500W Power Supply AC Power Cords

          237
    • 2700W AC-Input and DC-Input Power Supplies

      238
      • FigureA-11 2700W AC-Input Power Supply

        238
      • FigureA-12 2700W DC-input Power Supply

        239
      • 2700W Power Supply Specifications

        240
        • TableA-13 2700W Power Supply Specifications

          240
      • 2700W Power Supply AC Power Cords

        243
        • TableA-14 2700W Power Supply AC Power Cords

          243
    • 3000W AC-Input Power Supply

      244
      • FigureA-13 3000W AC-Input Power Supply

        244
      • 3000W Power Supply Specifications

        245
        • TableA-15 3000W Power Supply Specifications

          245
      • 3000W Power Supply AC Power Cords

        247
        • TableA-16 3000W Power Supply AC Power Cords

          247
    • 4000W AC-Input and DC-Input Power Supplies

      248
      • FigureA-14 4000W AC-Input Power Supply

        248
      • FigureA-15 4000W DC-Input Power Supply

        249
      • 4000W Power Supply Specifications

        249
        • TableA-17 4000W AC-Input and DC-Input Power Supplies Specifications

          249
      • 4000W Power Supply AC Power Cords

        252
        • TableA-18 4000W Power Supply AC Power Cords

          252
    • 6000W AC-Input Power Supply

      253
      • FigureA-16 6000W AC-Input Power Supply

        253
      • 6000W Power Supply Specifications

        254
        • TableA-19 6000W AC-Input Power Supply Specifications

          254
      • 6000W Power Supply AC Power Cords

        256
        • TableA-20 6000W Power Supply AC Power Cords

          256
    • AC Power Cord Illustrations

      257
      • FigureA-17 CAB-AC10A-90L-AU=

        257
      • FigureA-18 CAB-AC10A-90L-EU=

        258
      • FigureA-19 CAB-AC10A-90L-IT=

        258
      • FigureA-20 CAB-AC15A-90L-US=

        258
      • FigureA-21 CAB-AC10A-90L-UK=

        259
      • FigureA-22 CAB-7KACR=

        259
      • FigureA-23 CAB-7KACA=

        259
      • FigureA-24 CAB-7KACE=

        260
      • FigureA-25 CAB-7KACI=

        260
      • FigureA-26 CAB-7KAC-15=

        260
      • FigureA-27 CAB-7KACU=

        261
      • FigureA-28 CAB-7513ACR=

        261
      • FigureA-29 CAB-7513ACA=

        261
      • FigureA-30 CAB-7513ACE=

        262
      • FigureA-31 CAB-AC-2500W-ISRL

        262
      • FigureA-32 CAB-7513ACI=

        262
      • FigureA-33 CAB-7513AC=

        263
      • FigureA-34 CAB-AC16A-CH=

        263
      • FigureA-35 CAB-7513ACSA=

        263
      • FigureA-36 CAB-ACS-10=

        264
      • FigureA-37 CAB-7513ACU

        264
      • FigureA-38 CAB-AC-2500W-EU

        264
      • FigureA-39 CAB-AC-2500W-INT=

        265
      • FigureA-40 CAB-AC-2500W-US1=

        265
      • FigureA-41 CAB-AC-C6K-TWLK=

        265
      • FigureA-42 CAB-ACS-16=

        266
      • FigureA-43 CAB-AC-16A-AUS=

        266
      • FigureA-44 CAB-C19-CBN=

        266
      • FigureA-45 WS-CAC-4000W-INT=

        267
      • FigureA-46 WS-CAC-4000W-US=

        267
    • Power Supply Redundancy

      267
      • TableA-21 Power Supply Redundancy

        268
      • TableA-22 Effects of Power Supply Configuration Changes

        268
        • B

          273
          • Transceivers, Module Connectors, and Cable Specifications

            273
    • Transceivers

      273
      • 100-MB Transceiver Modules

        274
        • TableB-1 100-MB Transceiver Modules Descriptions

          274
          • FigureB-1 100-MB SFP Transceiver Module

            274
      • 1-GB Transceiver Modules

        275
        • TableB-2 1-GB Transceiver Modules Descriptions

          275
        • TableB-3 GBIC Transceiver Module Cabling Specifications

          277
        • TableB-4 SFP Transceiver Module Cabling Specifications

          278
          • FigureB-2 1000BASE-T GBIC Transceiver Module (WS-G5483)

            278
          • FigureB-3 1000BASE-X GBIC Transceiver Modules (WS-G5484, WS-G5486, and WS-G5487)

            278
          • FigureB-4 1000BASE-T SFP Transceiver Module (GLC-T)

            279
          • FigureB-5 1000BASE-X SFP Transceiver Modules (GLC-SX-MM, GLC-LH-SM, and GLC-ZX-SM)

            279
      • 10-GB Transceiver Modules

        280
        • TableB-5 10-GB Transceiver Modules

          280
        • TableB-6 10-GB XENPAK Transceiver Modules Specifications and Cabling Distances

          281
          • FigureB-6 10-Gigabit XENPACK Transceiver Module

            282
      • WDM Transceiver Modules

        282
        • TableB-7 WDM Transceiver Modules Descriptions

          282
          • TableB-8 CWDM GBIC Transceivers

            284
          • FigureB-7 CWDM GBIC Transceiver

            285
            • TableB-9 DWDM GBIC Transceiver Module Product Numbers and ITU Channel Numbers

              285
          • FigureB-8 DWDM GBIC Transceiver Module

            286
            • TableB-10 CWDM SFP Transceiver Modules

              286
          • FigureB-9 CWDM SFP Transceiver

            287
            • TableB-11 DWDM XENPAK Transceiver Module Product Numbers and ITU Channel Numbers

              287
          • FigureB-10 DWDM XENPAK Transceiver Module

            289
    • Module Connectors

      289
      • RJ-45 Connector

        289
        • FigureB-11 RJ-45 Interface Cable Connector

          290
      • RJ-21 Connector

        290
        • FigureB-12 RJ-21 Telco Interface Cable Connectors

          291
          • TableB-12 RJ-21 Connector Pinout

            292
      • RJ-21 Connector (WS-X6624-FXS Only)

        293
        • TableB-13 RJ-21 Connector Pinout (WS-X6224-FXS Analog Interface Module Only)

          293
      • SC Connector

        294
        • FigureB-13 SC Fiber-Optic Connector

          294
      • MT-RJ Connector

        294
        • FigureB-14 MT-RJ Connector

          295
      • LC Connector

        295
        • FigureB-15 LC Fiber Optic Connector

          295
    • Cables

      296
      • TableB-14 10/100BASE-T Crossover Cable Pinout (MDI-X)

        296
      • FigureB-16 Twisted-Pair Crossover 10/100BASE-T Cable Schematic

        296
        • TableB-15 1000BASE-T Crossover Cable Pinout (MDI-X)

          297
      • FigureB-17 Twisted-Pair Crossover 1000BASE-T Cable Schematic

        297
      • Console Port Mode Switch

        298
      • Identifying a Rollover Cable

        298
        • FigureB-18 Identifying a Rollover Cable

          298
      • Console Port Mode 1 Signaling and Pinouts

        299
        • DB-9 Adapter (for Connecting to a PC)

          299
          • TableB-16 Port Mode 1 Signaling and Pinouts (DB-9 Adapter)

            299
        • DB-25 Adapter (for Connecting to a Terminal)

          299
          • TableB-17 Port Mode 1 Signaling and Pinouts (DB-25 Adapter)

            299
        • Modem Adapter

          300
          • TableB-18 Port Mode 1 Signaling and Pinouts (Modem Adapter)

            300
      • Console Port Mode 2 Signaling and Pinouts

        300
        • TableB-19 Port Mode 2 Signaling and Pinouts (Port Mode Switch Out)

          300
      • Mode-Conditioning Patch Cord

        301
        • Patch Cord Configuration Example

          301
          • FigureB-19 Patch Cord Configuration

            301
        • Patch Cord Installation

          302
          • FigureB-20 Patch Cord Installation

            302
        • Differential Mode Delay

          302
          • FigureB-21 LED Transmission Compared to Laser Transmission

            303
    • Cleaning the Fiber Optic Connectors

      303
      • Step1 Use a lint-free tissue soaked in 99 percent pure isopropyl alcohol to gently wipe the face...

        304
      • Step2 Remove any residual dust from the faceplate with clean, dry, oil-free compressed air.

        304
      • Step3 Use a magnifying glass or inspection microscope to inspect the ferrule at an angle. Do not...

        304
        • C

          305
          • Repacking theSwitch

            305
      • Step1 Set the chassis in the bottom pallet. (SeeFigureC-1.)

        305
      • Step2 Place the packing bag over the chassis.

        305
      • Step3 Place the front-packing material and power supply packing material around the chassis.

        305
      • Step4 Place the power supplies in the spaces provided in the power supply packing material. (See...

        305
      • Step5 Place the top-packing material over the top of the chassis and power supplies.

        305
      • Step6 Place the rack-mount kit and the accessory kit on the top-packing material.

        305
      • Step7 Place the outside carton over the entire package.

        305
      • Step8 Fold the outside carton down over the top and seal with packing tape.

        305
      • Step9 Wrap three packing straps tightly around the top and bottom of the package to hold the out...

        305
        • FigureC-1 PackingMaterial

          306
        • FigureC-2 Final Package

          306
          • D

            307
            • Chassis and Module Power and Heat Values

              307
        • TableD-1 Power Requirements and Heat Dissipation—Chassis and Fan Trays

          307
        • TableD-2 Power Requirements and Heat Dissipation—IP Phones

          308
        • TableD-3 Power Requirements and Heat Dissipation—Supervisor Engines

          309
        • TableD-4 Power Requirements and Heat Dissipation—Modules

          310
          • E

            317
            • Troubleshooting

              317
    • Getting Started

      317
    • Solving Problems at the System Component Level

      318
    • Identifying Startup Problems

      319
      • Step1 Turn on the power supplies. You should immediately hear the system fan assembly begin to o...

        319
      • Step2 Verify that the LEDs on the supervisor engine light as follows:

        319
      • Step3 Verify that the STATUS LEDs on the supervisor engine and on each switching module are gree...

        319
      • Step4 If the startup information and system banner do not display at startup, refer to the Catal...

        319
    • Troubleshooting the Power Supply

      320
      • Step1 Verify that the INPUT OK LED on the power supply is green.

        320
      • Step2 If you have a second (redundant) power supply, repeat Step 1 for this power supply.

        320
    • Troubleshooting the Fan Assembly

      321
      • Step1 Verify that the FAN LED on the fan assembly is green.

        321
      • Step2 Verify that the FAN LED is red.

        321
    • Troubleshooting Modules

      321
      • Step1 Verify that all status LEDs are on.

        321
      • Step2 If any status LEDs on the supervisor engine or any switching modules are red or off, the m...

        321
      • STATUS LED Indications

        321
        • TableE-1 Environmental Monitoring for Supervisor Engine and Switching Modules

          322
    • Contacting Customer Service

      323
  • Numerics

    325
  • A

    326
  • B

    327
  • C

    327
  • D

    330
  • E

    330
  • F

    331
  • G

    331
  • I

    331
  • L

    331
  • M

    332
  • O

    332
  • P

    332
  • R

    333
  • S

    333
  • T

    334
  • U

    335
  • V

    335
  • W

    335
  • X

    335