BenutzerhandbuchInhaltsverzeichnisCisco7010 and Cisco 7505 ChassisReplacementInstructions1Product Overview2Figure1 Cisco7010—Interface Processor End2Figure2 Cisco7505—Interface Processor End2Figure3 Chassis Cover Panel3Prerequisites4Safety Guidelines4General Safety Precautions4Safety with Electricity4Lifting Safely5Preventing Electrostatic Discharge (ESD) Damage5Cable Strain Relief6Preparing the Work Area6Figure4 Chassis Footprint and Clearance Requirements for Maintenance7Tools and Parts Required8Replacing the Chassis8Replacing a Rack-Mounted Chassis9Removing the Existing Chassis from the Rack10Step 1 Turn off the system power and disconnect the power cord and all interface cables from the ...10Step 2 Have a second person support the chassis while you perform this step. From the front of th...10Step 3 Pull the chassis out of the rack and place it on the floor or a table.10Step 4 Use a number2 Phillips screwdriver to loosen and remove the two M4 x 10-mm, Phillips flat...10Step 5 Pull the ears off the chassis, and place the ears and all fasteners aside.10Installing the New Chassis in the Rack10Step 1 Position the chassis so that the end that will be in the front of the rack is closest to y...10Step 2 Attach the right chassis ear to the chassis first. Hold the ear in the orientation shown i...10Step 3 Insert the two studs through the holes on the side of the chassis. The ear should be flush...10Step 4 Insert two M4 x 10-mm, Phillips flathead screws through the ears and into the chassis side...10Step 5 Repeat Steps2through4 for the left ear. The strip of mounting holes on the front of eac...11Figure5 Installing the Ears on the Chassis11Step 6 Lift the chassis and move it to the rack. Avoid sudden twists or moves to prevent injury.11Step 7 Insert the rear of the chassis into the rack, pushing it back until the ears meet the fron...11Step 8 From the front of the rack, insert all eight 10-32x3/8-inch, slotted screws (four on eac...11Step 9 When all screws are inserted, use a 1/4-inch, flat-blade screwdriver to tighten each one.11Figure6 Installing the Chassis in a Standard Four-Post, 19-Inch Equipment Rack12Installing the Cable Management Brackets12Figure7 Cable Management Brackets—Cisco 7010 Shown13Step 1 If you have new brackets to install on the new chassis, proceed to Step4. If you are remo...13Step 2 At the interface processor end of the existing chassis, push the cables out of the cutouts...13Step 3 Use a number1 Phillips screwdriver to remove the sixpanhead screws (threeper bracket) t...13Step 4 At the interface processor end of the new chassis, place a bracket on one of the inner sid...13Step 5 Insert and finger-tighten three M3 Phillips screws from the inner side of the chassis, thr...13Step 6 When all three screws are inserted, use the number1 Phillips screwdriver to tighten the s...13Step 7 Repeat Steps 4 through 6 for the second bracket.13Step 8 When connecting the network interface cables or installing processor modules with the inte...13Moving Processor Modules14Figure8 Ejector Levers and Captive Installation Screws15Step 1 Before moving any processor modules, ensure that you have met the following prerequisites ...16Step 2 Note the slot location of the interface processor you will move. Before removing the inter...16Step 3 If necessary, disconnect any interface cables that are connected to the processor module.16Step 4 Use a screwdriver to loosen both of the captive installation screws. (See Figure8a.)16Step 5 Place your thumbs on the end of each ejector and simultaneously pull them both outward, aw...16Step 6 Grasp the carrier handle with one hand and pull the processor module straight out of the s...16Step 7 Place the processor module in the same slot position in the new chassis and align the notc...16Step 8 While keeping the carrier at a 90-degree orientation to the backplane, carefully slide the...16Step 9 Using the thumb and forefinger of each hand to pinch each ejector, simultaneously push bot...17Step 10 Use a screwdriver to tighten the two captive screws to prevent the processor module from ...17Step 11 Repeat Steps2through10 for the remaining interface processors.17Step 12 Repeat Steps3through10 for the SP (or SSP) and RP in the Cisco 7010, and the RSP1 in t...17Figure9 Handling a Processor Module17Checking the Installation18Step 1 Ensure that the system power switch is in the off position, then reconnect the power cable...18Step 2 Connect all interface cables to the appropriate interface processor ports. Ensure that all...18Step 3 Ensure that you have either a console terminal connected to the system console port or a p...18Step 4 Turn on the system power. The DC OK LED should go on and stay on. If if does, proceed to t...18Step 5 While the system initializes, the yellow boot error LED on the RP should go on for about t...18Step 6 When the system boot is complete, the RP or RSP1 begins to initialize the interface proces...19Step 7 If the enabled LED on a single interface processor remains off, suspect that the interface...19Step 8 If an enabled LED still fails to go on after performing these steps, suspect that the spec...19Step 9 Verify that the console terminal displays a script and system banner similar to the follow...19Step 10 After the system initializes, use the various show commands to display the status of the ...19show Command Descriptions and Examples20Cisco Information Online22Größe: 311 KBSeiten: 22Language: EnglishHandbuch öffnen
