Benutzerhandbuch für DELL X8300-6059

Inhaltsverzeichnis

• Dell™ XPS™ 8300 Service Manual

  1
• Notes, Cautions, and Warnings

  2
• Contents

  3
• Technical Overview

  9
  • Inside View of Your Computer

    9
  • System Board Components

    10
• Before You Begin

  13
  • Technical Specifications

    13
  • Recommended Tools

    13
  • Turning Off Your Computer

    13
    • 1 Save and close all open files and exit all open programs.

      13
    • 2 To shut down the operating system, click Start and then click Shut Down.

      13
    • 3 Ensure that the computer is turned off. If your computer did not automatically turn off when you shut down the operating system, press and hold the power button until the computer turns off.

      14
  • Safety Instructions

    14
    • 1 Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.

      14
    • 2 Turn off your computer (see "Turning Off Your Computer" on page 13) and all attached devices.

      14
    • 3 Disconnect all telephone or network cables from the computer.

      14
    • 4 Disconnect your computer and all attached devices from their electrical outlets.

      14
    • 5 Disconnect all attached devices from your computer.

      14
    • 6 Press and eject any installed cards from the Media Card Reader.

      14
    • 7 Press and hold the power button to ground the system board.

      14
• Computer Cover

  17
  • Removing the Computer Cover

    17
    • 1 Follow the instructions in "Before You Begin" on page 13.

      17
    • 2 Lay the computer on its side with the computer cover facing up.

      17
    • 3 Remove the thumbscrew that secures the computer cover to the chassis, using a screw driver, if necessary.

      17
    • 4 Release the computer cover by sliding it away from the front of the computer.

      17
    • 5 Lift the cover away from the computer and set it aside in a secure location.

      17
  • Replacing the Computer Cover

    18
    • 1 Follow the instructions in "Before You Begin" on page 13.

      18
    • 2 Connect all the cables and fold the cables out of the way.

      18
    • 3 Ensure that no tools or extra parts are left inside the computer.

      18
    • 4 Align the tabs at the bottom of the computer cover with the slots located along the edge of the chassis.

      18
    • 5 Press the computer cover down and slide it towards the front of the computer.

      18
    • 6 Replace the thumbscrew that secures the computer cover to the chassis.

      18
    • 7 Place the computer in an upright position.

      19
• Memory Module(s)

  21
  • Removing the Memory Module(s)

    21
    • 1 Follow the instructions in "Before You Begin" on page 13.

      21
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      21
    • 3 Locate the memory module(s) on the system board (see "System Board Components" on page 10).

      21
    • 4 Press out the securing clip at each end of the memory module connector.

      21
    • 5 Grasp the memory module and pull it upwards.

      22
  • Replacing the Memory Module(s)

    22
    • 1 Follow the instructions in "Before You Begin" on page 13.

      22
    • 2 Press out the securing clip at each end of the memory module connector.

      22
    • 3 Align the notch on the bottom of the memory module with the tab in the connector.

      23
    • 4 Insert the memory module into the connector until the memory module snaps into position.

      24
    • 5 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      25
    • 6 Connect your computer and devices to electrical outlets, and then turn them on.

      25
    • 7 Log on to your computer.

      25
• Front Bezel

  27
  • Removing the Front Bezel

    27
    • 1 Follow the instructions in "Before You Begin" on page 13.

      27
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      27
    • 3 Place the computer in an upright position.

      27
    • 4 Grasp and release the front bezel tabs sequentially, one at a time by moving them outward from the front panel.

      27
    • 5 Rotate and pull the front bezel away from the front of the computer to release the front bezel clamps from the front panel slots.

      27
    • 6 Set aside the front bezel in a secure location.

      28
  • Replacing the Front Bezel

    29
    • 1 Follow the instructions in "Before You Begin" on page 13.

      29
    • 2 Align and insert the front bezel clamps into the front panel slots.

      29
    • 3 Rotate the front bezel towards the computer until the front bezel tabs snap into place.

      29
    • 4 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      30
• Graphics Card Bracket

  31
  • Removing the Graphics Card Bracket

    31
    • 1 Follow the instructions in "Before You Begin" on page 13.

      31
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      31
    • 3 Remove the two screws that secure the graphics card bracket to the chassis.

      31
    • 4 Lift the graphics card bracket off the chassis.

      31
    • 5 Set the graphics card bracket aside in a secure location.

      31
  • Replacing the Graphics Card Bracket

    32
    • 1 Follow the instructions in "Before You Begin" on page 13.

      32
    • 2 Align the screw holes on the graphics card bracket with the screw holes on chassis.

      32
    • 3 Replace the two screws that secure the graphics card bracket to the chassis.

      32
    • 4 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      32
  • Wireless Mini-Card

    33
    • Removing the Mini-Card

      33
    • Replacing the Mini-Card

      34
• PCI Express Cards

  37
  • Removing the Card Retention Bracket

    37
    • 1 Follow the instructions in "Before You Begin" on page 13.

      37
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      37
    • 3 Remove the screw that secures the card retention bracket.

      37
    • 4 Lift the card retention bracket and set it aside in a secure location.

      37
  • Replacing the Card Retention Bracket

    38
    • 1 Follow the instructions in "Before You Begin" on page 13.

      38
    • 2 Replace the card retention bracket, ensuring that:

      38
    • 3 Replace the screw that secures the card retention bracket.

      38
    • 4 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      38
  • Removing PCI Express Cards

    39
    • 1 Follow the instructions in "Before You Begin" on page 13.

      39
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      39
    • 3 Remove the graphics card bracket, if applicable (see "Removing the Graphics Card Bracket" on page 31).

      40
    • 4 Remove the card retention bracket (see "Removing the Card Retention Bracket" on page 37).

      40
    • 5 Disconnect any cables connected to the card, if applicable.

      40
    • 6 Remove the PCI Express card from the card slot:

      40
    • 7 If you are removing the card permanently, install a filler bracket in the empty card-slot opening.

      41
  • Replacing PCI Express Cards

    41
    • 1 Follow the instructions in "Before You Begin" on page 13.

      41
    • 2 Prepare the card for installation.

      41
    • 3 Place the PCI Express card in the slot on the system board and press down firmly. Ensure that the PCI Express card is fully seated in the slot.

      41
    • 4 Replace the card retention bracket (see "Replacing the Card Retention Bracket" on page 38).

      41
    • 5 Connect any cables that should be attached to the card.

      42
    • 6 Replace the graphics card bracket, if applicable (see "Replacing the Graphics Card Bracket" on page 32).

      42
    • 7 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      42
    • 8 Reconnect the computer and devices to electrical outlets, and then turn them on.

      42
    • 9 To complete the installation, see "Configuring Your Computer After Removing or Installing the PCI Express Card" on page 42.

      42
  • Configuring Your Computer After Removing or Installing the PCI Express Card

    42
    • 1 Enter system setup (see "System Setup Utility" on page 103)

      43
    • 2 Go to Onboard Audio Controller and then change the setting to Disabled.

      43
    • 3 Connect the external audio devices to the sound card’s connectors.

      43
    • 1 Enter system setup (see "System Setup Utility" on page 103)

      43
    • 2 Go to Onboard Audio Controller and then change the setting to Enabled.

      43
    • 3 Connect the external audio devices to the computer’s back panel connectors.

      43
    • 1 Enter system setup (see "System Setup Utility" on page 103)

      43
    • 2 Go to Onboard LAN Controller and then change the setting to Disabled.

      43
    • 3 Connect the network cable to the network card’s connector.

      43
    • 1 Enter system setup (see "System Setup Utility" on page 103)

      43
    • 2 Go to Onboard LAN Controller and then change the setting to Enabled.

      43
    • 3 Connect the network cable to the integrated network connector.

      43
• Drives

  45
  • Hard Drive

    45
    • Removing the Primary Hard Drive

      45
      • 1 Follow the instructions in "Before You Begin" on page 13.

        45
      • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

        45
      • 3 Disconnect the power and data cables from the hard drive.

        45
      • 4 Remove the four screws that secure the hard drive to the chassis.

        45
      • 5 Slide the hard drive out towards the back of the computer.

        46
      • 6 If removing the hard drive changes the drive configuration, ensure that you reflect these changes in the system setup (see "System Setup Utility" on page 103).

        46
    • Removing the Hard Drive Cage

      46
      • 1 Follow the instructions in "Before You Begin" on page 13.

        46
      • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

        46
      • 3 Remove the primary hard drive (see "Removing the Primary Hard Drive" on page 45).

        47
      • 4 Remove the three screws that secure the hard drive cage to the chassis.

        47
      • 5 If applicable, disconnect the power and data cables from the secondary hard drive (see "System Board Components" on page 10).

        47
      • 6 Slide the hard drive cage towards the back of the chassis.

        47
    • Removing the Secondary Hard Drive

      47
      • 1 Follow the instructions in "Before You Begin" on page 13.

        47
      • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

        48
      • 3 Remove the primary hard drive (see "Removing the Primary Hard Drive" on page 45).

        48
      • 4 Remove the hard drive cage (see "Removing the Hard Drive Cage" on page 46).

        48
      • 5 Remove the four screws that secure the secondary hard drive to the hard drive cage.

        48
      • 6 Slide the secondary hard drive away from the hard drive cage.

        48
    • Replacing the Secondary Hard Drive

      48
      • 1 Follow the instructions in "Before You Begin" on page 13.

        48
      • 2 Check the documentation that shipped with the hard drive to verify that it is configured for your computer.

        49
      • 3 Slide the secondary hard drive into the hard drive cage.

        49
      • 4 Align the screw holes on the secondary hard drive with the screw holes on the hard drive cage.

        49
      • 5 Replace the four screws that secure the secondary hard drive to the hard drive cage.

        49
    • Replacing the Hard Drive Cage

      49
      • 1 Follow the instructions in "Before You Begin" on page 13.

        49
      • 2 Align the screw holes on the hard drive cage with the screw holes on the chassis.

        49
      • 3 Replace the three screws that secure the hard drive cage to the chassis.

        49
      • 4 If applicable, connect the power and data cables to the secondary hard drive (see "System Board Components" on page 10).

        49
    • Replacing the Primary Hard Drive

      49
      • 1 Follow the instructions in "Before You Begin" on page 13.

        49
      • 2 Check the documentation that shipped with the drive to verify that it is configured for your computer.

        49
      • 3 Slide the primary hard drive into the hard drive cage.

        49
      • 4 Align the screw holes on the primary hard drive with the screw holes on the chassis.

        49
      • 5 Replace the four screws that secure the primary hard drive to the chassis.

        49
      • 6 Connect the power and data cables to the primary hard drive (see "System Board Components" on page 10).

        49
      • 7 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

        49
      • 8 Connect your computer and devices to electrical outlets, and then turn them on.

        49
      • 9 See the documentation that shipped with the hard drive for instructions on installing any software required for drive operation.

        49
      • 10 Check the System Setup for drive configuration changes (see "System Setup Utility" on page 103).

        50
  • Optical Drive

    50
    • Removing the Optical Drive

      50
      • 1 Follow the instructions in "Before You Begin" on page 13.

        50
      • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

        50
      • 3 Remove the front bezel (see "Removing the Front Bezel" on page 27).

        50
      • 4 Disconnect the power and data cables from the optical drive.

        50
      • 5 Remove the two screws that secure the optical drive to the chassis.

        50
      • 6 Push and slide the optical drive out through the front of the computer.

        50
      • 7 Set aside the optical drive in a secure location.

        51
    • Replacing the Optical Drive

      51
      • 1 Follow the instructions in "Before You Begin" on page 13.

        51
      • 2 Remove the screw from the old optical drive and insert it in the new optical drive.

        51
      • 3 To install a secondary optical drive, insert a screw driver and twist it to remove the break-away metal plate.

        52
      • 4 Pull the break-away metal plate away from the chassis.

        52
      • 5 Gently slide the optical drive into the optical drive bay through the front of the computer.

        53
      • 6 Align the screw holes on the optical drive with the screw holes on the chassis.

        53
      • 7 Replace the two screws that secure the optical drive to the chassis.

        53
      • 8 Connect the power and data cables to the optical drive (see "System Board Components" on page 10).

        54
      • 9 Replace the front bezel (see "Replacing the Front Bezel" on page 29).

        54
      • 10 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

        54
      • 11 Connect your computer and devices to electrical outlets, and turn them on.

        54
      • 12 See the documentation that shipped with the drive for instructions on installing any software required for drive operation.

        54
      • 13 Check the System Setup for drive configuration changes (see "System Setup Utility" on page 103).

        54
  • Media Card Reader

    54
    • Removing the Media Card Reader

      54
      • 1 Follow the instructions in "Before You Begin" on page 13.

        54
      • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

        54
      • 3 Remove the front bezel (see "Removing the Front Bezel" on page 27).

        54
      • 4 Remove the optical drive (see "Removing the Optical Drive" on page 50).

        54
      • 5 Remove the top cover (see "Removing the Top Cover" on page 57).

        54
      • 6 Remove the two screws that secure the Media Card Reader to the front panel. The screws are located below the Media Card Reader.

        54
      • 7 Disconnect the Media Card Reader cable from the system board connector F_USB1 (see "System Board Components" on page 10).

        54
      • 8 Slide and lift the Media Card Reader to remove it from the top panel.

        54
    • Replacing the Media Card Reader

      56
      • 1 Follow the instructions in "Before You Begin" on page 13.

        56
      • 2 Gently slide the Media Card Reader guides into the slots in the top panel.

        56
      • 3 Replace the two screws that secure the Media Card Reader to the front panel.

        56
      • 4 Connect the Media Card Reader cable to the system board connector F_USB1 (see "System Board Components" on page 10).

        56
      • 5 Replace the top cover (see "Replacing the Top Cover" on page 59).

        56
      • 6 Replace the optical drive (see "Replacing the Optical Drive" on page 51).

        56
      • 7 Replace the front bezel (see "Replacing the Front Bezel" on page 29).

        56
      • 8 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

        56
      • 9 Connect your computer and devices to electrical outlets, and then turn them on.

        56
• Top Cover

  57
  • Removing the Top Cover

    57
    • 1 Follow the instructions in "Before You Begin" on page 13.

      57
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      57
    • 3 Remove the front bezel (see "Removing the Front Bezel" on page 27).

      57
    • 4 Remove the optical drive (see "Removing the Optical Drive" on page 50).

      57
    • 5 Pull the release tab, and slide the top cover towards the front of the computer to release the top cover tabs from the slots on the top panel.

      57
    • 6 Pull the top cover away from the top panel.

      57
    • 7 Set the top cover aside in a secure location.

      58
  • Replacing the Top Cover

    59
    • 1 Follow the instructions in "Before You Begin" on page 13.

      59
    • 2 Align the tabs on the top cover with the slots on the top panel.

      59
    • 3 Press and slide the top cover towards the back of the computer, until it clicks into place.

      59
    • 4 Replace the optical drive (see "Replacing the Optical Drive" on page 51).

      59
    • 5 Replace the front bezel (see "Replacing the Front Bezel" on page 29).

      59
    • 6 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      59
• Top I/O Panel

  61
  • Removing the Top I/O Panel

    61
    • 1 Follow the instructions in "Before You Begin" on page 13.

      61
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      61
    • 3 Remove the front bezel (see "Removing the Front Bezel" on page 27).

      61
    • 4 Remove the optical drive (see "Removing the Optical Drive" on page 50).

      61
    • 5 Remove the top cover (see "Removing the Top Cover" on page 57).

      61
    • 6 Disconnect the top I/O panel cables from the system board connectors, F_USB3 and F_AUDIO1 (see "System Board Components" on page 10).

      61
    • 7 Remove the two screws that secure the top I/O panel to the top panel.

      61
    • 8 Carefully remove the top I/O panel from the top panel.

      62
  • Replacing the Top I/O Panel

    63
    • 1 Follow the instructions in "Before You Begin" on page 13.

      63
    • 2 Align the screw holes on the top I/O panel with the screw holes on the top panel.

      63
    • 3 Replace the two screws that secure the top I/O panel to the top panel.

      63
    • 4 Connect the top I/O panel cables to the system board connectors, F_USB3 and F_AUDIO1 (see "System Board Components" on page 10).

      63
    • 5 Replace the top cover (see "Replacing the Top Cover" on page 59).

      63
    • 6 Replace the optical drive (see "Replacing the Optical Drive" on page 51).

      63
    • 7 Replace the front bezel (see "Replacing the Front Bezel" on page 29).

      63
    • 8 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      63
    • 9 Connect your computer and devices to electrical outlets, and turn them on.

      63
• Front USB Panel

  65
  • Removing the Front USB Panel

    65
    • 1 Follow the instructions in "Before You Begin" on page 13.

      65
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      65
    • 3 Remove the front bezel (see "Removing the Front Bezel" on page 27).

      65
    • 4 Disconnect the front USB panel cables from the system board connector F_USB2 (see "System Board Components" on page 10).

      65
    • 5 Remove the screw that secures the front USB panel to the front panel.

      65
    • 6 Slide the front USB panel down to release the clamps from the front panel and pull it away.

      65
  • Replacing the Front USB Panel

    67
    • 1 Follow the instructions in "Before You Begin" on page 13.

      67
    • 2 Align and slide the front USB panel clamps into the front USB panel clamp slot.

      67
    • 3 Replace the screw that secures the front USB panel to the front panel.

      67
    • 4 Connect the front USB panel cables to the system board connector F_USB2 (see "System Board Components" on page 10).

      67
    • 5 Replace the front bezel (see "Replacing the Front Bezel" on page 29).

      67
    • 6 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      67
    • 7 Connect your computer and devices to electrical outlets, and turn them on.

      67
• Bluetooth Assembly

  69
  • Removing the Bluetooth Assembly

    69
    • 1 Follow the instructions in "Before You Begin" on page 13.

      69
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      69
    • 3 Remove the front bezel (see "Removing the Front Bezel" on page 27).

      69
    • 4 Disconnect the Bluetooth assembly cable from the system board connector F_USB4 (see "System Board Components" on page 10).

      69
    • 5 Press in on the tab as shown in the illustration and pull the Bluetooth assembly away from the front panel.

      69
    • 6 Carefully slide and remove the Bluetooth assembly cable through the slot in the front panel.

      69
    • 7 Set the Bluetooth assembly aside in a secure location.

      70
  • Replacing the Bluetooth Assembly

    71
    • 1 Follow the instructions in "Before You Begin" on page 13.

      71
    • 2 Slide the Bluetooth assembly cable through the slot on the front panel.

      71
    • 3 Align the Bluetooth assembly tab with the Bluetooth assembly slot in the front panel.

      71
    • 4 Press in on the Bluetooth assembly tab, and push it towards the front panel until it clicks into place.

      71
    • 5 Connect the Bluetooth assembly cable to the system board connector, F_USB4 (see "System Board Components" on page 10).

      71
    • 6 Replace the front bezel (see "Replacing the Front Bezel" on page 29).

      71
    • 7 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      71
    • 8 Connect your computer and devices to electrical outlets, and turn them on.

      71
• Power Button Module

  73
  • Removing the Power Button Module

    73
    • 1 Follow the instructions in "Before You Begin" on page 13.

      73
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      73
    • 3 Remove the front bezel (see "Removing the Front Bezel" on page 27).

      73
    • 4 Remove the optical drive (see "Removing the Optical Drive" on page 50).

      73
    • 5 Remove the top cover (see "Removing the Top Cover" on page 57).

      73
    • 6 Disconnect the power button module cable from the system board connector, F_PANEL (see "System Board Components" on page 10).

      73
    • 7 Press the power button module tabs and lift the power button module to release it from the top panel.

      73
    • 8 Set the power button module aside in a secure location.

      74
  • Replacing the Power Button Module

    75
    • 1 Follow the instructions in "Before You Begin" on page 13.

      75
    • 2 Align and push the power button module tabs into the slots on the top panel.

      75
    • 3 Connect the power button module cable to the system board connector, F_PANEL (see "System Board Components" on page 10).

      75
    • 4 Replace the top cover (see "Replacing the Top Cover" on page 59).

      75
    • 5 Replace the optical drive (see "Replacing the Optical Drive" on page 51).

      75
    • 6 Replace the front bezel (see "Replacing the Front Bezel" on page 29).

      75
    • 7 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      75
    • 8 Connect your computer and devices to electrical outlets and turn them on.

      75
• Fans

  77
  • Chassis Fan

    77
    • Removing the Chassis Fan

      77
      • 1 Follow the instructions in "Before You Begin" on page 13.

        77
      • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

        77
      • 3 Disconnect the chassis fan cable from the system board connector SYS_FAN1 (see "System Board Components" on page 10).

        77
      • 4 Remove the four screws that secure the chassis fan to the chassis.

        77
      • 5 Slide and lift the chassis fan away from the computer as shown in the illustration.

        77
    • Replacing the Chassis Fan

      78
      • 1 Follow the instructions in "Before You Begin" on page 13.

        78
      • 2 Align the screw holes on the chassis fan with the screw holes on the chassis.

        78
      • 3 Replace the four screws that secure the chassis fan to the chassis.

        78
      • 4 Connect the chassis fan cable to the system board connector SYS_FAN1 (see "System Board Components" on page 10).

        78
      • 5 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

        78
  • Processor Fan and Heat-Sink Assembly

    79
    • Removing the Processor Fan and Heat-Sink Assembly

      79
      • 1 Follow the instructions in "Before You Begin" on page 13.

        79
      • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

        79
      • 3 Disconnect the processor fan cable from the system board connector, CPU_FAN (see "System Board Components" on page 10).

        79
      • 4 Using a flat-blade screwdriver loosen the four captive screws that secure the processor fan and heat-sink assembly to the system board.

        79
      • 5 Lift the processor fan and heat-sink assembly out of the computer.

        79
    • Replacing the Processor Fan and Heat-Sink Assembly

      81
      • 1 Follow the instructions in "Before You Begin" on page 13

        81
      • 2 Clean the thermal grease from the bottom of the heat-sink.

        81
      • 3 Apply new thermal grease to the top of the processor.

        81
      • 4 Place the processor fan and heat-sink assembly over the processor.

        81
      • 5 Align the four captive screws on the processor fan and heat-sink assembly with the screw holes on the system board.

        81
      • 6 Tighten the four captive screws that secure the processor fan and heat-sink assembly to the system board.

        81
      • 7 Connect the processor fan cable to the system board connector, CPU_FAN (see "System Board Components" on page 10).

        81
      • 8 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

        81
      • 9 Connect your computer and devices to electrical outlets, and turn them on.

        81
  • Processor

    83
    • Removing the Processor

      83
    • Replacing the Processor

      85
• Coin-Cell Battery

  89
  • Removing the Coin-Cell Battery

    89
    • 1 Record all the screens in system setup (see "System Setup Utility" on page 103) so that you can restore the correct settings after the new coin- cell battery has been installed.

      89
    • 2 Follow the instructions in "Before You Begin" on page 13.

      89
    • 3 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      89
    • 4 Locate the battery socket on the system board (see "System Board Components" on page 10).

      89
    • 5 Press the battery-release lever to remove the coin-cell battery.

      89
    • 6 Set aside the battery in a secure location.

      90
  • Replacing the Coin-Cell Battery

    90
    • 1 Follow the instructions in "Before You Begin" on page 13

      90
    • 2 Insert the new coin-cell battery (CR2032) into the socket with the side labeled "+" facing up, and press the coin-cell battery into place.

      90
    • 3 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      91
    • 4 Connect your computer and devices to electrical outlets, and then turn them on.

      91
    • 5 Enter system setup (see "System Setup Utility" on page 103) and restore the settings you recorded in step 1.

      91
• Power Supply

  93
  • Removing the Power Supply

    93
    • 1 Follow the instructions in "Before You Begin" on page 13.

      93
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      93
    • 3 Disconnect the DC power cables from the system board and the drives (see "System Board Components" on page 10).

      93
    • 4 Remove the four screws that secure the power supply to the chassis.

      93
    • 5 Press the power supply clamps to release the power supply from the chassis.

      93
    • 6 Slide and lift the power supply away from the chassis.

      93
  • Replacing the Power Supply

    95
    • 1 Follow the instructions in "Before You Begin" on page 13.

      95
    • 2 Slide the power supply towards the back of the chassis.

      95
    • 3 Align the screw holes on the power supply with the screw holes on the chassis.

      95
    • 4 Replace the four screws that secure the power supply to the chassis.

      95
    • 5 Connect the DC power cables to the system board and drives (see "System Board Components" on page 10).

      95
    • 6 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      95
    • 7 Connect your computer and devices to electrical outlets, and turn them on.

      95
• System Board

  97
  • Removing the System Board

    97
    • 1 Follow the instructions in "Before You Begin" on page 13.

      97
    • 2 Remove the computer cover (see "Removing the Computer Cover" on page 17).

      97
    • 3 Remove the Mini-Card, if applicable (see "Removing the Mini-Card" on page 33).

      97
    • 4 Remove any PCI Express cards, if applicable (see "Removing PCI Express Cards" on page 39).

      97
    • 5 Remove the processor fan and heat-sink assembly (see "Removing the Processor Fan and Heat-Sink Assembly" on page 79).

      97
    • 6 Remove the processor (see "Removing the Processor" on page 83).

      97
    • 7 Remove the memory modules (see "Removing the Memory Module(s)" on page 21) and record which memory module is removed from each DIMM slot so that the memory modules can be installed in the same slot after the system board is replaced.

      97
    • 8 Disconnect all cables connected to the system board (see "System Board Components" on page 10). Note the routing of all cables as you remove them so that you can re-route them correctly after installing the new system board.

      98
    • 9 Remove the eight screws that secure the system board to the chassis.

      98
    • 10 Lift the system board up and out of the chassis.

      99
    • 11 Compare the system board that you removed with the replacement system board to ensure that they are identical.

      99
  • Replacing the System Board

    99
    • 1 Follow the instructions in "Before You Begin" on page 13.

      99
    • 2 Gently place the system board into the chassis and slide it towards the back of the computer.

      99
    • 3 Replace the eight screws that secure the system board to the chassis.

      99
    • 4 Connect the cables that you disconnected from the system board (see "System Board Components" on page 10).

      99
    • 5 Replace the processor (see "Replacing the Processor" on page 85).

      99
    • 6 Replace the processor fan and the heat-sink assembly (see "Replacing the Processor Fan and Heat-Sink Assembly" on page 81).

      99
    • 7 Replace the memory modules (see "Replacing the Memory Module(s)" on page 22).

      99
    • 8 Replace any PCI Express cards, if applicable (see "Replacing PCI Express Cards" on page 41).

      99
    • 9 Replace the Mini-Card, if applicable (see "Replacing the Mini-Card" on page 34).

      99
    • 10 Replace the computer cover (see "Replacing the Computer Cover" on page 18).

      99
    • 11 Connect your computer and devices to electrical outlets and turn them on.

      99
    • 12 Flash the system BIOS, as needed.

      100
  • Entering the Service Tag in the BIOS

    101
    • 1 Turn on the computer.

      101
    • 2 Press <F2> during POST to enter the system setup program.

      101
    • 3 From the main tab enter the service tag in the Set Service Tag field.

      101
  • System Setup Utility

    103
    • Overview

      103
      • Entering System Setup Utility

        103
      • System Setup Options

        104
      • Boot Sequence

        109
    • Clearing Forgotten Passwords

      110
    • Clearing CMOS Passwords

      112
  • Flashing the BIOS

    115