BenutzerhandbuchInhaltsverzeichnisDESCRIPTION AND SPECIFICATIONS1Component Checklist of Typical System (Package Contents)1System Overview1IMPS 4000 (Optional)1SPS 4000 (Optional)1Model 751 Remote Powered Loop LCD Display1Probe Options1Specifications1INSTALLATION2Mechanical Installation2without SPS 4000)2without SPS 4000)2Electrical Installation (for Oxymitter 4000 with SPS 4000)2Pneumatic Installation (for Oxymitter 4000 without SPS 4000)2Pneumatic Installation (for Oxymitter 4000 with SPS 4000)2IMPS 4000 Connections2CONFIGURATION OF OXYMITTER 4000 WITH MEMBRANE KEYPAD3General3Logic I/O3Recommended Configuration3CONFIGURATION OF OXYMITTER 4000 WITH LOI4General4Logic I/O4Recommended Configuration4Power Up5General operation5STARTUP AND OPERATION OF OXYMITTER 4000 WITH LOI6Power Up6Start Up Oxymitter 4000 Calibration6Navigating the Local Operator Interface6LOI Key Designations6LOI Menu Tree6Oxymitter 4000 Setup at the LOI6LOI Installation6Oxymitter 4000 Test Points6Model 751 Remote Powered Loop LCD Display (Optional)6HART/AMS7Overview7HART Communicator Signal Line Connections7Hart Communicator PC Connections7Off-Line and On-Line Operations7Logic I/O Configurations7Menu Tree for HART Communicator/Oxymitter 4000 Applications7HART Communicator Manual O2 Cal Method7Defining a Timed Calibration Via HART7TROUBLESHOOTING8Overview8General8Alarm Indications8Alarm Contacts8Identifying and Correcting Alarm Indications with Membrane Keypad8Oxymitter 4000 Passes Calibration, but Still Reads Incorrectly8SPS 4000 Troubleshooting8MAINTENANCE AND SERVICE9Overview9Calibration – Oxymitter 4000 with a Membrane Keypad9Calibration – Oxymitter 4000 with a Local Operator Interface (LOI)9Oxymitter 4000 Repair9SPS 4000 Maintenance and Component Replacement9RETURN OF MATERIAL10REPLACEMENT PARTS11OPTIONAL ACCESSORIES12INDEX13Typical System Package1Oxymitter 4000 Autocalibration System Options1Membrane Keypad1Local Operator Interface (LOI)1Model 751 LCD Display Panel1Oxymitter 4000 HART Communications and AMS Application1Typical System Installation – Oxymitter 4000 with Integral Electronics1Typical System Installation – Oxymitter 4000 with Remote Electronics1SPS 40001Model 751 Remote Powered Loop LCD Display1Ceramic Diffusion Assembly1Snubber Diffusion Assembly1Hastelloy Cup-Type Diffusion Assembly1Abrasive Shield Assembly1Oxymitter 4000 Probe Installation2Oxymitter 4000 Remote Electronics Installation2Oxymitter 4000 Installation (with SPS 4000)2Oxymitter 4000 with Abrasive Shield2Oxymitter 4000 Adapter Plate Dimensions2Oxymitter 4000 Adapter Plate Installation2Oxymitter 4000 Abrasive Shield Bracing Installation2Orienting the Optional Vee Deflector2Installation with Drip Loop and Insulation Removal2Electrical Installation – Oxymitter 4000 with Integral Electronics2Electrical Installation – Oxymitter 4000 with Remote Electronics2SPS 4000 Electrical Connections2Air Set, Plant Air Connection2Oxymitter 4000 Gas Connections Calibration Gas Connections2Electronics Housing Terminals and Membrane Keypad3Defaults – Oxymitter 4000 with Membrane Keypad3Electronics Housing Terminals and LOI4Defaults – Oxymitter 4000 with LOI4Startup and Normal Operation5Calibration Keys5Startup Display6O2 Concentration Display6LOI Features6Menu Tree for Local Operator Interface on the Oxymitter 40006LOI Module Connectors6Oxymitter 4000-Test Points6Signal Line Connections, ≥ 250 Ohms Load Resistance7Signal Line Connections, < 250 Ohms Load Resistance7Menu Tree for HART/AMS on the Oxymitter 40007O2 Sensor mV Reading vs. % O2 at 736ºC (Reference Air, 20.9% O2)8Diagnostic LEDs8Fault 1, Open Thermocouple8Fault 2, Shorted Thermocouple8Fault 3, Reversed Thermocouple8Fault 4, A/D Comm Error8Fault 5, Open Heater8Fault 6, High High Heater Temp8Fault 7, High Case Temp8Fault 8, Low Heater Temp8Fault 9, High Heater Temp8Fault 10, High Cell mV8Fault 11, Bad Cell8Fault 12, EEPROM Corrupt8Fault 13, Invalid Slope8Fault 14, Invalid Constant8Fault 15, Last Calibration Failed8Probe Leakage Paths8SPS 4000 Troubleshooting Flowchart8Membrane Keypad9Inside Right Cover9Oxymitter 4000 with Integral Electronics, Exploded View9Oxymitter 4000 with Remote Electronics, Exploded View9Electronic Assembly9J8 Connector9Fuse Location9Heater Strut Assembly9Probe to Probe Head Assembly – Remote Electronics Only9Cell Replacement Kit9Ceramic Diffusion Element Replacement9Termination Housing Connections for Remote Electronics Probe Head9SPS 4000 Manifold Assembly9Power Supply Board and Interface Board Connections9Calibration Gas and Reference Air Components9Cell Replacement Kit11Probe Disassembly Kit11Product Matrix1Calibration Components1Intelligent Multiprobe Test Gas Sequencer Versions1Logic I/O Configuration (as set at HART/AMS or LOI)3Logic I/O Configuration (as set at HART/AMS or LOI)4Logic I/O Configuration7Diagnostic/Unit Alarm Fault Definitions – Membrane Keypad Only8Diagnostic/Unit Alarm Fault Definitions – LOI8SPS 4000 Fault Finding8Replacement Parts for Probe11Replacement Parts for Electronics11Replacement Parts for SPS 400011Replacement Parts for Calibration Components11Größe: 3,54 MBSeiten: 172Language: EnglishHandbuch öffnen
