BenutzerhandbuchInhaltsverzeichnisDocument Reference2Important Safety instructions10Safety symbols11Introduction to FreeSpeak II™12An FS II communication system13FreeSpeak II system capacity14Installing a system14Placing the Base station16Placing the antennas and splitters16Wiring the antennas and splitters17Power supplies to the components of an FS II System18Determining coverage areas19Doing a site survey to determine coverage areas20Doing a site survey with a beltpack20Testing antenna handoff22Getting information on active antenna status23Assigning beltpacks to coverage areas23Conditions affecting coverage areas24Registering beltpacks24station25Connecting the Base station28Understanding the Back-Panel Connectors29Connecting to partyline intercom systems32Clear-Com and compatible partyline32Connecting directly to Clear-Com partyline beltpacks33Connecting to an RTS™ wired beltpack34Front-panel adjustments for partyline connections34Troubleshooting partyline connections35Wireless partyline37Connecting to 4-Wire and digital matrix intercom38Connecting to Clear-Com matrix plus40Connecting to Clear-Com Eclipse digital matrix40Connecting with other digital matrix intercom systems41Connecting with other 4-wire devices41Connecting to a program audio source42IFB configuration42Connecting to the stage announce output43Connecting to a PC44Connecting using the serial port44Connecting using the LAN port46Connecting to transceiver/antennas46port46Connecting transceiver/antennas with a splitter (PD2203)47Powering an antenna or antenna splitter48Operating the Base station49Introduction49Understanding Front-Panel Operation50Call Channel A50Call Channel B50Programming a system from the Base station54Introduction55Using the Base station’s programming menus56Saving changes56Changing beltpack labels56To change a beltpack label56Setting and changing port labels58To create a port label58Setting and changing group labels60To create a group label60Adding group members62To assign members to a group62Beltpacks63Assigning audio routes to a beltpack63Setting the beltpack audio level66Setting beltpack latching67Over the Air (OTA) beltpack registration from the Base station67Setting input and output port levels67Input level68Output level68To set the audio level for a port68Setting port call destination69Configuring a wired partyline71To select the type of partyline system for a partyline port72To configure the Noise Gate for a partyline port73To configure the levels for a partyline port74Base station System Menu76System Info77Restoring the Defaults77Antennas78Setting the IP address79Locking front-panel enable buttons79Remote microphone kill80Kill beltpack microphones80Kill partyline microphones80Kill all microphones80Battery indicator80Operating the wireless beltpack81Overview of the wireless beltpack81Beltpack user controls84Top controls84Beltpack display85Beltpack headset tones/alerts85Front controls86Beltpack bottom connectors88Beltpack rear panel89Using the beltpack90Registering the beltpack90Charging the beltpack90Powering on the beltpack91Using the beltpack to communicate91Entering and exiting Menu mode92Setting and Adjusting Listen Levels92Upgrading beltpack firmware92Programming on the beltpack94Introduction to programming on the beltpack94Configuring the beltpack volume settings95Configuring the beltpack channel volumes and master volume96Configuring the volume level of the line input96Configuring the rotary controls96Configuring the beltpack headset97Setting headset autodetect97Setting the sidetone level98Setting the headset limiter98Configuring the beltpack microphone98Setting the microphone type99Setting the microphone echo cancellation99Configuring the beltpack display and LEDs99Setting the display and LED brightness100Setting the display dim timeout100Setting the display off timeout100Configuring the beltpack alarm options101Setting the low battery alarm101Setting the low battery alarm threshold102Setting the out of range alarm102Setting the call alert102Selecting the beltpack role default set103Selecting the beltpack administration103Enabling OTA registration mode104Setting full menu access104Setting system sync mode105Setting the listen again option105Accessing beltpack information106Setting display mode106Setting system connect106Performing a site survey107Operating the transceiver/antenna109Transceiver/antenna109IP rating (International Protection Marking)109FS II transceiver/antenna connector panel110Cabling the antennas111Beltpack support capacities for transceiver/antennas111Coverage areas under various conditions112Transceiver/antenna setup rules and tips112Upgrading the antenna/transceiver firmware113Transceiver/antenna splitter (PD2203)113PD2203 Front connector panel114PD2203 rear panel115transceiver/antennas116FS II Configuration Editor117Loading configurations118Loading a local configuration file118link119Loading a configuration from a Base station using Ethernet120Configuration Editor121Configuration Editor Screen basics122Registering beltpacks using the over the air (OTA) facility123Configuring beltpacks126Selecting the beltpack to register or edit126Registering beltpacks using the micro USB cable126Viewing beltpack registration information127Viewing beltpack properties127Beltpack audio levels129Beltpack alarm options130Setting the beltpack role options131Assigning beltpack keys133Configuring the Reply key134Key assignment types135Configuring ports135Selecting the port to edit136Changing the label of the port136Selecting the port type136Selecting a communication path for the port137Setting the input, output and VOX levels139Configuring groups and wireless partylines139Selecting the group to edit140Changing the label of the group140Changing the members of the group141Displaying a group overview141Reducing antenna interference142Configuring IFBs142Selecting the IFB to edit143Changing the label of the IFB143Changing the IFB sources143Setting the IFB dim level143Configuring Base station system parameters144Editing the system parameters:144Enabling Over The Air (OTA) registration145Diagnostics145Beltpack status146Static log147Antenna status148Antenna roles149Event Log149Upgrading the Configuration Editor150Upgrading the Base station from FS to FS II151Setting the Base station IP address151Upgrading the Base station firmware151Upgrading the Base station FPGA151Loading the default map152Specifications154FreeSpeak II Base station154FreeSpeak II Beltpack155FreeSpeak II Transceiver/Antenna156FreeSpeak II Transceiver/Antenna Splitter156Transmission Method157Compliance158Größe: 2,79 MBSeiten: 161Language: EnglishHandbuch öffnen
Internal PhotosInhaltsverzeichnisXCVR2G4A circuit side1XCVR2G4A comp side without shield2Größe: 3,77 MBSeiten: 2Handbuch öffnen
External PhotosInhaltsverzeichnis20150402_1437031External photos2XCVR2G4A circuit side2XCVR2G4A comp side without shield3Größe: 4,65 MBSeiten: 3Handbuch öffnen
