Benutzerhandbuch für iSi North America ADV8

Inhaltsverzeichnis

• I. WARNINGS

  4
• TO THE OWNER

  4
• TO THE INSTALLER

  4
• TRANSPORTATION DAMAGE

  4
• II. SAFETY

  4
• ADDITIONAL SAFETY CONSIDERATIONS

  5
• ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

  5
• III. PRODUCT APPLICATION

  5
• IV. LOCATION REQUIREMENTS AND CONSIDERATIONS

  6
• GENERAL

  6
• CLEARANCES AND ACCESSIBILITY

  7
• HORIZONTAL INSTALLATION (AMV MODELS ONLY)

  7
• FURNACE SUSPENSION

  7
• EXISTING FURNACE REMOVAL

  8
• THERMOSTAT LOCATION

  8
• V. COMBUSTION AND VENTILATION AIR REQUIREMENTS

  8
• VI. CATEGORY I VENTING (VERTICAL VENTING)

  11
• VII. EXTERIOR MASONRY CHIMNEYS

  11
• CHECKLIST SUMMARY

  12
• CHECK 1 - PROPER CHIMNEY TERMINATION.

  12
• CHECK 2 - ANY SOLID OR LIQUID FUEL APPLIANCES VENTED INTO THIS CHIMNEY CHANNEL

  13
• CHECK 3 - CHIMNEY CROWN CONDITION.

  13
• CHECK 4 - DEBRIS IN CLEANOUT

  13
• CHECK 5 - LINER CONDITION.

  13
• CHECK 6 - DILUTION AIR.

  14
• CHECK 7 - COMPLETE THE INSTALLATION.

  14
• FIX 1 - LINER TERMINATION

  14
• FIX 2 -CHANGE VENTING ARRANGEMENTS

  14
• FIX 3 - REBUILD THE CROWN

  14
• FIX 4 - RELINING

  14
• VIII. ELECTRICAL CONNECTIONS

  15
• WIRING HARNESS

  15
• 115 VOLT LINE CONNECTIONS

  15
• JUNCTION BOX RELOCATION

  15
• 24 VOLT THERMOSTAT WIRING

  16
• SETTING THE HEAT ANTICIPATOR

  17
• SINGLE-STAGE THERMOSTAT APPLICATION

  17
• 24 VOLT DEHUMIDISTAT WIRING

  17
• FOSSIL FUEL APPLICATIONS

  17
• 115 VOLT LINE CONNECTION OF ACCESSORIES (HUMIDIFIER AND ELECTRONIC AIR CLEANER)

  18
• 24 VAC HUM

  18
• IX. GAS SUPPLY AND PIPING

  18
• GENERAL

  18
• HIGH ALTITUDE DERATE

  18
• PROPANE GAS CONVERSION

  20
• GAS PIPING CONNECTIONS

  20
• GENERAL

  20
• UPFLOW INSTALLATIONS

  21
• COUNTERFLOW INSTALLATIONS

  21
• GAS PIPING CHECKS

  21
• PROPANE GAS TANKS AND PIPING

  21
• PROPANE GAS PIPING CHARTS

  22
• X. CIRCULATING AIR AND FILTERS

  22
• DUCTWORK - AIR FLOW

  22
• FILTERS - READ THIS SECTION BEFORE INSTALLING THE RETURN AIR DUCTWORK

  22
• UPRIGHT INSTALLATIONS

  22
• CIRCULATION AIR FILTERS

  22
• HORIZONTAL INSTALLATIONS

  23
• XI. SEQUENCE OF OPERATION

  23
• (INTEGRATED IGNITION CONTROL)

  23
• NORMAL HEATING SEQUENCE

  23
• NORMAL COOLING SEQUENCE - INTEGRATED IGNITION CONTROL

  23
• CONSTANT FAN

  23
• XII. START-UP PROCEDURE AND ADJUSTMENT

  24
• FURNACE OPERATION

  24
• FURNACE START-UP

  24
• FURNACE SHUTDOWN

  24
• GAS SUPPLY PRESSURE MEASUREMENT

  24
• GAS MANIFOLD PRESSURE MEASUREMENT AND ADJUSTMENT

  25
• GAS INPUT RATE MEASUREMENT (NATURAL GAS ONLY)

  25
• TEMPERATURE RISE

  26
• CIRCULATOR BLOWER SPEED ADJUSTMENT

  26
• ADJUST BLOWER HEAT OFF DELAY

  27
• CIRCULATOR BLOWER FAN TIMING ADJUSTMENT

  28
• XIII. OPERATIONAL CHECKS

  28
• BURNER FLAME

  28
• AUXILIARY LIMIT CONTROL

  28
• PRIMARY LIMIT

  28
• XIII. SAFETY CIRCUIT DESCRIPTION

  28
• GENERAL

  29
• INTEGRATED CONTROL MODULE

  29
• PRIMARY LIMIT

  29
• AUXILIARY LIMIT

  29
• ROLLOUT LIMITS

  29
• PRESSURE SWITCHES

  29
• FLAME SENSOR

  29
• XV. TROUBLESHOOTING

  29
• ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

  29
• DIAGNOSTIC CHART

  29
• RESETTING FROM LOCKOUT

  29
• XVI. MAINTENANCE

  29
• ANNUAL INSPECTION

  30
• FILTERS

  30
• FILTER MAINTENANCE

  30
• FILTER REMOVAL

  30
• UPRIGHT FILTER REMOVAL

  30
• INDUCED DRAFT AND CIRCULATOR BLOWER MOTORS

  30
• FLAME SENSOR (QUALIFIED SERVICER ONLY)

  30
• IGNITER (QUALIFIED SERVICER ONLY)

  30
• BURNERS

  30
• XVII. BEFORE LEAVING AN INSTALLATION

  31
• XVIII. REPAIR AND REPLACEMENT PARTS

  31