Benutzerhandbuch für JAI TS-1327EN

Inhaltsverzeichnis

• VIS elements

  2
• Back shot VIS installation.

  3
• Typical Over Lane Site Layout

  5
• Typical Over Lane Site Layout Plan.

  6
• VIS 300 U.S. Camera options chart.

  8
• VIS 300 European Camera options chart.

  11
• Typical side of road installation.

  14
• Typical side of road installation plan view with no canopy/overhead structue.

  14
• Flash and camera distances.

  15
• Install the traffic light sensor.

  17
• TLS-300 signal and power cable.

  18
• Installing the TLS-300 through the mounting pipe and flange.

  18
• Pipe clamps should be about 6-inches apart on a vertical surface.

  19
• Camera Installation

  19
• Camera mount template.

  20
• Camera cabling as it appears before electrical installation.

  20
• Cable final wiring.

  21
• Properly wired X-4 connector.

  22
• Back of the video camera.

  22
• VIS CAM connections

  24
• TLS 300 to J-Panel wiring.

  25
• X-6 Power input connection.

  26
• Wiring for the X8 to converter connector.

  27
• Test trigger

  28
• Two lane controller

  29
• TNF-31 flash unit

  29
• S3 switch setting

  30
• Connecting an AC flash.

  30
• Connection for LVD to VIS CAM 400.

  31
• Example of a network connection using a local switch.

  35
• Initial Camera Alignment Display example.

  37
• Roll Bar Display example.

  38
• Readjustment of camera tilt and zoom display.

  39
• Focus Bar marker display.

  40
• Focus Bar Waveform display.

  41
• Focus Bar Waveform Display with waveform cursors

  42
• Connection requirements.

  45
• Component layout of the EN board.

  46
• Board connections

  47
• Interface drawing.

  48
• Electrical interface

  48
• Physical interface table

  49
• Category 5 or 6 wiring diagram.

  50
• Flash connections.

  50
• I/O board electrical interface. Test

  51
• Switch location.

  51
• Connecting DC Flash to a board powered from the Flash power supply.

  52
• Connection DC Flash to an internally powered board.

  52
• AC flash unit connection.

  53
• Second flash connection.

  53
• IO board electrical interface.

  54
• Wiring a second DC flash from the flash power supply.

  55
• Connecting the second AC flash.

  56
• Connecting to the night light (TNC 100)

  57
• Detection board

  57
• LVD Trigger Input

  58
• Electrical interface on the I/O board:

  58
• Ethernet test connectors.

  59
• EN network test configuration setup.

  60
• Test setup 2.

  61
• Auxiliary power connector

  62
• EN-CAM component layout.

  65
• Connecting from J-Panel to camera zero.

  65
• J-Panel electrical interface

  66
• Ethernet wiring diagram.

  68
• Board and camera J-panel connection to camera 1.

  69
• J-panel electrical interface

  70
• Category 5 or 6 ethernet wiring diagram.

  71
• Light sensor indicator on the board

  72
• Light sensor connector

  72
• Signal to J-panel #2

  73
• Signal from J-panel #1

  74
• Signal from J-panel #1

  75
• Principle in the power distribution.

  76
• RS485 to Ethernet

  76
• Interface from Camera 0

  77
• Interface from Camera 1

  78
• External Trigger connection.

  79
• Trigger polarity

  80
• Trigger 0

  80
• Trigger 1

  80
• Lane controller setup diagram

  81
• Lane controller setup.

  82
• Two camera, one flash, configuration.

  83
• Terminal block

  85
• Standard configuration of Basic Settings:

  87
• Standard configuration of Network Settings:

  88
• Standard configuration of Serial settings for port 1:

  89
• Standard configuration of Serial settings for port 2:

  90
• Configuration overview of serial port 1 and 2.

  90
• Operation configuration of Serial port 1:

  91
• Operation configuration of Serial port 2:

  92
• Configuration overview of operating settings for serial port 1 and 2.

  92
• Moxa configuration example.

  93
• Network cabling example:

  95
• Light Sensor Cables

  18
• Electrical wiring for the VIS CAM installation.

  21
• VIS CAM connections to the J-Panel.

  23
• TLS 300 to J-Panel connections

  24
• Power input to the J-Panel

  25
• X8 to converter connector

  26
• Trigger input connector

  27
• X15 Lane Controller

  28
• Flash unit connection in VIS CAM 400.

  29
• Optimal Illumination Distance Between Camera and TNF

  30
• Wiring for LVD to VIS CAM 400.

  31
• Typical minimum plate heights and nominal plate heights:

  34
• Optimal Illumination Distance Between Camera and TNF

  43
• Wiring diagram.

  51
• Physical interface pinouts.

  55
• Connector table

  59
• Signal parameters and conditions.

  66
• Physical interface table

  67
• LED indicators

  68
• Switch labels

  68
• Signal table

  70
• Ethernet physical connections

  71
• LED indicators

  72
• Connector switches

  72
• Physical interface connections

  73
• LED physical indicators

  73
• Physical connector table for J-panel 2.

  74
• Physical pin connections J-panel #1.

  75
• Physical connection for pins.

  76
• RS485 physical connections

  77
• Physical connector description

  78
• Pin connections for Ethernet from Camera 1

  79
• Connector table

  81
• WAGO physical interface

  82
• Master to slave connections.

  84
• Essential specifications for the pluggable terminal block.

  85
• Troubleshooting table.

  97