Datenbogen (NUCLEO-F103RB)InhaltsverzeichnisTable 1. Device summary11 Ordering information2Table 2. Ordering information22 Revision history2Table 3. Document revision history2Größe: 218 KBSeiten: 3Language: EnglishHandbuch öffnen
Datenbogen (NUCLEO-F103RB)Inhaltsverzeichnis1 Ordering information62 Conventions73 Quick start83.1 Getting started83.2 System requirements84 Features94.1 Hardware configuration variants95 Hardware layout and configuration105.1 Cutable PCB125.2 Embedded ST-LINK/V2-1135.2.1 Drivers145.2.2 ST-LINK/V2-1 firmware upgrade145.2.3 Using the ST-LINK/V2-1 to program/debug the STM32 on board145.2.4 Using ST-LINK/V2-1 to program/debug an external STM32 application155.3 Power supply and power selection165.3.1 Power supply input from the USB connector165.3.2 External power supply inputs: VIN and EV517Using VIN or E5V as external power supply185.3.3 External power supply input: + 3V3205.3.4 External power supply output205.4 LEDs205.5 Push buttons215.6 JP6 (IDD)215.7 OSC clock225.7.1 OSC clock supply225.7.2 OSC 32 kHz clock supply235.8 USART communication235.9 Solder bridges245.10 Extension connectors265.11 Arduino connectors315.12 STMicroelectronics Morpho connector426 Mechanical drawing487 Electrical schematics498 References539 Revision history53Größe: 1,77 MBSeiten: 54Language: EnglishHandbuch öffnen
Datenbogen (NUCLEO-F103RB)InhaltsverzeichnisFigure 1. STM32 Nucleo board (1)11 Ordering information6Table 1. Ordering information62 Conventions7Table 2. ON/OFF conventions73 Quick start83.1 Getting started83.2 System requirements84 Features95 Hardware layout and configuration10Figure 2. Hardware block diagram10Figure 3. Top layout11Figure 4. Bottom layout125.1 Cutable PCB125.2 Embedded ST-LINK/V2-113Table 3. Jumper states13Figure 5. Typical configuration135.2.1 Drivers14Figure 6. Updating the list of drivers in Device Manager145.2.2 ST-LINK/V2-1 firmware upgrade145.2.3 Using the ST-LINK/V2-1 to program/debug the STM32 on board14Figure 7. Connecting the STM32 Nucleo board to program the on-board STM32155.2.4 Using ST-LINK/V2-1 to program/debug an external STM32 application15Table 4. Debug connector CN4 (SWD)15Figure 8. Using ST-LINK/V2-1 to program the STM32 on an external application165.3 Power supply and power selection165.3.1 Power supply input from the USB connector16Table 5. JP1 configuration table175.3.2 External power supply inputs: VIN and EV517Table 6. External power sources17Table 7. Power-related jumper185.3.3 External power supply input: + 3V319Table 8. +3.3V eternal power source195.3.4 External power supply output195.4 LEDs195.5 Push buttons205.6 JP6 (IDD)205.7 OSC clock215.7.1 OSC clock supply215.7.2 OSC 32 kHz clock supply225.8 USART communication225.9 Solder bridges23Table 9. Solder bridges235.10 Extension connectors25Figure 9. NUCLEO-F030R825Figure 10. NUCLEO-F072RB25Figure 11. NUCLEO-F103RB26Figure 12. NUCLEO-F302R826Figure 13. NUCLEO-F401RE27Figure 14. NUCLEO-L152RE275.11 Arduino connectors28Table 10. Arduino connectors on NUCLEO-F030R8, NUCLEO-F072RB28Table 11. Arduino connectors on NUCLEO-F103RB30Table 12. Arduino connectors on NUCLEO-F302R832Table 13. Arduino connectors on NUCLEO-F401RE34Table 14. Arduino connectors on NUCLEO-L152RE355.12 STMicroelectronics Morpho connector37Table 15. STMicroelectronics Morpho connector on NUCLEO-F030R837Table 16. STMicroelectronics Morpho connector on NUCLEO-F072RB38Table 17. STMicroelectronics Morpho connector on NUCLEO-F103RB39Table 18. STMicroelectronics Morpho connector on NUCLEO-F302R840Table 19. STMicroelectronics Morpho connector on NUCLEO-F401RE41Table 20. STMicroelectronics Morpho connector on NUCLEO-L152RE426 Mechanical drawing43Figure 15. STM32 Nucleo board mechanical drawing437 Electrical schematics44Figure 16. Schematic (1/4)44Figure 17. Schematic (2/4)45Figure 18. Schematic (3/4)46Figure 19. Schematic (4/4)478 References489 Revision history48Table 21. Document revision history48Größe: 1,51 MBSeiten: 49Language: EnglishHandbuch öffnen
