Benutzerhandbuch für Thermo Products ome-72d36

Inhaltsverzeichnis

• OIL-FIRED FURNACE

  1
• DOWN FLOW & DIRECT VENT (SEALED COMBUSTION)

  1
• MODEL: OME-72D36

  1
• INSTALLATION AND SERVICE MANUAL

  1
• FOR YOUR SAFETY

  1
• WHAT TO DO IF YOU SMELL GAS

  1
  • I. SAFETY SECTION

    2
• control system which has been underwater.

  4
• TABLE OF CONTENTS

  7
  • IV. INSTALLATION 10

    7
  • APPENDIX A - REPLACEMENT PARTS LIST 45

    7
• II. GENERAL INSTRUCTIONS AND CLEARANCES

  8
• NOTE: READ THIS SECTION BEFORE STARTING INSTALLATION

  8
  • III. FURNACE SPECIFICATIONS

    10
  • Low Fire High Fire1

    10
  • HEAT INPUT RATE (BTUH) 70,000 85,000

    10
• ELECTRICAL SUPPLY: 120 VAC / 60HZ / 1 PHASE

  10
• MAXIMUM TIME DELAY TYPE FUSE OR HACR BREAKER RATING: 15 AMPS

  10
  • DIMENSIONS & WEIGHTS:

    10
  • CABINET: WIDTH - 18 IN., DEPTH – 24-3/4 IN., HEIGHT - 57 IN.

    10
• WARM AIR DUCT: WIDTH – 12 IN., DEPTH – 12 IN., HEIGHT - 14 ¼ IN.

  10
• FILTER QUANTITY & SIZE: (1) @ 18 IN. x 24 IN. x 1 IN. EA.

  10
• BURNER DATA

  10
  • MODEL: AFG

    10
  • AIR TUBE LENGTH (IN.): 3

    10
  • HEAD DESIGN: F-3

    10
• PRESSURE (P.S.I.G.) 120

  10
• BLOWER DATA

  11
• MANUFACTURER: MORRISON PRODUCTS, INC.

  11
• BLOWER MODEL:12-9T, DIRECT DRIVE

  11
  • STATIC PRESSURES 1195

    11
  • A. ROOF JACK

    12
• B. STANDARD CHIMNEY

  12
• C. FURNACE LOCATION

  12
• Combustible Floor Base

  13
• Model: 70-BASE

  13
• Figure 1A.

  13
• Cottage Base

  13
• Model: 01COT-BASE

  13
• Figure 1B.

  13
• D. BASE INSTALLATION

  13
• 1. Combustible Floor Base Model: 70-BASE

  13
• Figure 2.

  14
• Figure 3.

  15
• 2. Cottage Base Model: 01COT-BASE

  15
• E. ALCOVE INSTALLATION

  17
• Alcove installations must use the No. 70 mobile home base.

  17
• Refer to section G. COMBUSTION AIR for additional combustion air requirements.

  17
• Figure 4.

  17
  • F. CLOSET INSTALLATION

    17
  • G. COMBUSTION AIR

    18
• Figure 6.

  20
• H. FUEL PIPING

  21
• 1. Oil Tank and Piping

  21
  • J. ELECTRICAL WIRING

    23
• If the heat anticipator is set too high, the furnace may delay activation of a heating cycle for too long. If the heat anticipator is set too low, the furnace may cycle too frequently. Either condition may not provide optimal comfort to the homeowner.

  25
  • “COOL” Blower cool speed tap

    26
• A. Inputs

  26
• B. Outputs

  26
• C. Operating Modes

  27
  • K. BURNER INSTALLATION

    31
  • L. BURNER OPERATION AND ADJUSTMENT

    31
  • M. FLUE GAS COMBUSTION ANALYSIS

    34
• For typical burner combustion analysis results, refer to the table below.

  34
• BURNER COMBUSTION PARAMETERS

  34
  • V. DEALER MAINTENANCE

    35
    • A. TROUBLESHOOTING

      35
• C. HEAT EXCHANGER CLEANING INSTRUCTIONS

  41
• Figure 8.

  42
• D. CLEANING OR REPLACING FLUE PIPES

  43
• E. EXTENDED SHUTDOWN

  43
• ON SHUT DOWN:

  43
• ON START-UP:

  43
  • VI. USER INFORMATION SECTION

    44
• A. WARNINGS AND CAUTIONS:

  44
• Should the furnace not operate – note diagnostic code through view port prior to removing doors. B. COMPONENT LOCATIONS

  44
• Figure 9.

  45
  • C. INSPECTION AREAS

    45
  • D. FILTER LOCATION AND CLEANING

    46
• See Figure 9, in this section, for the location of the return air filter.

  46
  • E. CONTACT INFORMATION: INSTALLATION / SERVICE

    46