BenutzerhandbuchInhaltsverzeichnisChapter 1: Overview91.1 About the Transport GT20 B516191.2 Features101.3 Unpacking121.3.1 Opening the Box121.3.2 Box Contents131.3.3 Accessories141 x Tyan driver CD14Mounting Bracket x 4151.4 About the Product161.4.1 Front View16CD-ROM Drive161.4.2 Rear View16Power Supply Socket161.4.3 LED Definition171.4.4 Internal View191.4.5 Motherboard Block Diagram201.4.6 Motherboard Layout21CPU socket32Chapter 2: Setting Up92.0.1 Before You Begin232.0.2 Work Area232.0.3 Tools232.0.4 Precautions242.1 Rack Mounting252.1.1 Installing the Server in a Rack251. Screw the mounting ear to each side of Transport GT20 as shown using 2 screws from the supplied screws kit.262. Draw out the inner rails from rail assembly. Install inner rails to left and right sides of chassis using 2 M4-5L(D) screws for each side.263. Measure the distance between inner side of the front and rear mounting brackets in the rack.264. Locate the front and rear brackets.275. Reserve 90mm for Transport GT20 on the front bracket. Secure the front bracket to outer rail with 2 M4-4L(C) screws.276. Reserve the distance same as in Step 2 on rear bracket. Secure the rear bracket to outer rail with 2 M4-4L(C) screws.287. Secure the outer rail to the rack using 2 brackets and 4 M4-8L(E) screws for each side (A). Secure the mounting brackets from inside, not outside, of the rack (B).288. Draw out the middle rail to the latch position.299. Lift the chassis and then insert the inner slide rails into the middle rails.2910. Push the chassis in and press the latch key (A). Then push the whole system into the rack (B).2911. Secure the mounting ears of chassis to the rack with 2 M4-15L(F) screws.302.2 Installing Motherboard Components312.2.1 Removing the Chassis Cover311. Release the screw on the back side. Then slide the chassis cover in the direction of arrow.312. Lift the cover off.312.2.2 Installing the CPU, Heatsink and Air Duct321. Release the pre-installed air duct. Locate the CPU socket.322. Remove the cover on the CPU socket.323. Locate the lever of CPU socket.324. Press and pull the lever in the direction as illustrated..335. Open the socket in the direction as illustrated.336. Place CPU on the socket, ensuring that the edge with triangle mark aims at the edge of socket with triangle mark.337. Close the cover and secure the CPU socket in the reverse procedures from step 2 to 6.348. Secure the heatsink with 4 screws. NOTE: Remember to install the washer and nut while installing the screws.349. Secure the air duct with 2 screws.342.2.3 Installing the Memory351. Locate the memory slots on the motherboard.352. Press the memory slot locking levers in the direction of the arrows as shown in the following illustration.353. Align the memory module with the slot. The module has indentations that align with notches in the slots.354. Insert the memory module into the slot as shown.352.2.4 Installing the PCI Card361. Push the tab of PCI slot on the rear panel in the direction as shown to release the bracket.362. Move the bracket to right as shown and then take off the bracket (A).363. Insert the PCI card in the directions of arrow (B).364. Push the tab of PCI slot on the rear panel in the direction as shown to fix PCI card.362.3 Installing the Hard Drive371. Press the locking lever latch in the direction of arrow (A) and then pull the locking lever open (B).372. Slide the drive tray out.373. Place a hard drive into the drive tray.374. Using 4 HDD screws to secure the HDD.385. Reinsert the drive tray into the chassis (A), ensuring that the drive tray is completely inserted into the chassis (B).386. Pressing the locking lever to secure the hard drive tray.382.4 Installing the Slim FDD (Option)391. Locate the two FDD rails and screws from the FDD kit. Secure the two rails to FDD using four screws.392. Connect the FFC cable to FDD.393. Use a screw driver to take off the door of FDD tray.394. Insert the FDD module into the tray.395. Connect the FFC cable to the FDD connector on M1012 adapter board.406. Locate the FDD cable from FDD kit. Connect the wrinkle side to the connector on M1012 adapter board. Refer to the picture below for the correct direction.407. Connect the other side to the connector on motherboard.40Chapter 3: Replacing Pre-Installed Components93.1 Introduction413.1.1 Work Area413.1.2 Tools413.1.3 Precautions423.2 Disassembly Flowchart433.3 Removing the Cover441. Release the screw on the back side. Then slide the chassis cover in the direction of arrow.442. Lift the cover off.443.4 Replacing Motherboard Components453.4.1 Disconnecting All Motherboard Cables451. Disconnect ATX power cables452. Disconnect the Fan, Front Panel, SATA and USB cables. Refer to the mainboard layout on p.13 for the locations.453. Disconnect the PWM cable .453.4.2 Removing the Motherboard461. Release the two screws securing the link bar.462. Remove the link bar.463. Remove the eleven screws securing the motherboard to the chassis.464. Remove the motherboard.463.5 Replacing the LED Control Board471. Remove the 2 screws securing the LED control board to the chassis.472. Pull the LED control board free from the chassis and unplug the ribbon and USB cables from the connector.473. Remove the three screws securing the LED control board to the bracket474. Release the LED control board from the chassis. After replacement, insert and secure the unit to the chassis following the reverse procedures from step 1~3.483.6 Replacing the M1012 Adapter Board491. Before replacing M1012 adapter board, you must disconnect the four SATA cables connected to the SATA backplane. After that, disconnect all the cables connected to the M1012 adapter board.492. Remove the Front Panel, LAN/ID LED and Fan Tach cables.493. Remove the Front Panel Control Board cable.494. Remove one power cable connected to M1012 adapter board and two power cables connected to SATA backplane.505. Remove the 6 screws securing the M1012 adapter board. After that, you can release the M1012 adapter board from the chassis.503.6.1 M1012 Adapter Board Features513.6.2 M1012 Adapter Board Connector Pin Definition523.6.3 System Fan Layout573.7 Replacing the SATA Backplane581. After removing the M1012 adapter board, you can easily grab the two lables to lift the SATA backplane.582. Remove the ten screws that secure the bracket to the backplane.583. Release the backplane free from the bracket.584. Replace the unit to the chassis following the reverse procedures from step 1 to 3 after done.583.7.1 S-ATA Backplane (M1204) Features593.8 Replacing the Cooling Fan611. Locate the fan connector on the motherboard and unplug the fan cable.612. Take the fan away from the chassis.613. Replace the fan into the chassis following the reverse procedures from 1 to 2 after done.613.9 Replacing the Power Supply621. Remove the two screws that secure the power supply to the chassis.622. Remove the screw that secure the fan assembly to the chassis62Appendix I: BIOS Differences1Appendix I: BIOS Differences1Appendix III: Installing SMDC Cards1Appendix I: BIOS Differences1Appendix III: Installing SMDC Cards1Appendix III: Installing SMDC Cards1Größe: 9,83 MBSeiten: 77Language: EnglishHandbuch öffnen