Benutzerhandbuch für Tyco Safety Products/Sensormatic CCW

Inhaltsverzeichnis

• Introduction

  9
  • Product Overview

    10
  • Access Badges and Asset Tags

    10
  • Handheld Reader

    10
  • RF Readers

    10
    • Antennas

      10
    • RF Controller

      11
    • RF Reader Configuration

      11
  • Specifications

    12
    • Electrical

      12
    • Environmental

      13
    • Regulatory

      13
• Basic Functionality

  15
  • Basic System Operation

    16
  • RF Controller Block

    17
    • Synchronization Circuitry

      17
    • Communications Interfaces

      17
• Planning

  19
  • RF Passage Reader Configurations

    20
    • Single-Antenna Configurations

      20
    • Multiple-Antenna Configurations

      20
    • Application-Specific Configuration Requirements

      20
  • Coordinating with Software Features

    21
  • Configuration Requirements

    21
    • RF Passage Antennas

      21
    • RF Controllers

      22
    • Inputs

      22
    • Outputs

      22
    • Host Panel

      22
    • RF Controller Power Supply

      22
    • External Power (to Power Supply)

      22
    • Cabling

      23
    • Asset Tag

      24
    • Access Control Badge

      24
  • Tools and Equipment

    24
• Installation

  25
  • Installation Checklist

    26
    • Phase 1: Hardware Installation

      26
    • Phase 2: System Activation and Test

      26
  • Install Cable Runs

    26
  • Install RF Passage Antennas

    26
    • Prepare for Installation

      26
    • Install brackets and Mount Antennas

      27
    • Install Wire Loop for Antenna Pairs

      27
    • Connect RF Controller Cables

      28
    • Install Finishing Hardware

      29
  • Install RF Controller

    29
    • Prepare for Installation

      29
    • Mount the RF Controller Enclosure

      29
    • Connect RF Antenna Cables

      30
    • Connect Inputs and Outputs

      32
    • Connect Communications Cable

      33
    • Connect Sync Cable

      33
  • Connect RF Reader at Panel

    34
  • Connect Power to RF€Controller

    34
    • Connect Model CW-RID-1 to AC Power

      34
  • Inspect Installation

    36
  • Apply Power

    36
  • Verify System Operation

    36
    • Functional Test

      36
    • Full System Test

      37
• Service

  39
  • Parts List

    40
  • RFID 56 Format

    40
  • Tune RF Passage Antennas

    40
  • DIP Switch Settings

    42
  • Troubleshooting Tips

    43
• Asset Tag Installation

  47
  • Overview

    48
  • Applying Adhesive Tape

    48
  • Applying 3M 4475 Plastic Adhesive

    48
  • Positioning Guidelines

    49
• Managing RF Passage Antenna Performance

  51
  • Performance Overview

    52
  • Environmental Conditions Affecting Performance

    52
    • Cable/Line Interference

      52
    • Antenna Loading

      52
    • Antenna Interference

      52
  • Antenna Performance

    53
    • One Antenna, .9m (3ft)

      53
    • One Antenna, 1.8m (6ft)

      53
  • Before You Begin

    54
  • Investigating Performance

    54
    • Check for Obvious Sources of Interference

      54
    • Check for Antenna Loading

      54
    • Investigate Antenna Interference

      54
    • Troubleshooting Tips

      55
      • Existing Installations

        55
      • Intermittent Interference

        55
      • Multiple Sources of Interference

        55
  • Improve Performance

    55
    • Control Cable/Line Interference

      55
    • Control Antenna Loading

      55
    • Control Antenna Interference

      55
  • Troubleshooting Procedures

    56
    • Isolate an Antenna

      56
    • Use a Communications Receiver

      56
      • Required Equipment

        56
      • Set Up the Receiver

        56
      • Searching for Source of Interference

        57
    • Install Cancellation Coils

      57
      • Before You Begin

        57
      • Required Equipment

        58
      • Plan Wiring Configuration

        58
      • Make Cancellation Coils

        58
      • Make Antenna Coupling Loop

        59
      • Prepare Antenna for Cancellation

        59
      • Install Antenna Coupling Loop

        59
      • Install Coils

        60
        • Connecting One Coil

          61
        • Connect Multiple Coils

          61
      • Finish the Installation

        62