Elation Professional DP-640B User Manual
2
1
4
3
6
7
8
9
5
4
Control and Functions
Overall Layout
3
1. Edison Output Sockets(1~6):
These are dual 120V Edison sockets for output. Each socket is labeled
with the relevant channel number. Up to 20Amps can be connected into
each channel.
with the relevant channel number. Up to 20Amps can be connected into
each channel.
2. Threaded Openings:
3. Bracket Knobs:
4. Resetable Circuit Breakers(x2pcs):
5. Mounting Slots:
6. Connectors:
7. Control Section:
8. Mounting Bracket:
9. Power Inputs:
These openings are supplied so the user can fasten the mounting bracket to
the desired side.
the desired side.
These knobs are used to fasten the hanging bracket to the chassis.
These two 20A circuit breakers, protect the corresponding internal
components from damage if there were ever a short circuit or voltage spike.
components from damage if there were ever a short circuit or voltage spike.
These slots are in place so the user could permanently mount the unit if
desired.
desired.
These are the DMX Input/Output connectors. There are 3 & 5 pin XLR inputs
and outputs.
and outputs.
These buttons are used to adjust relevant settings within the display.
This mounting bracket is used to fasten the unit to a truss structure.
These supply power to the relevant channels when connect. Line cord 1
supplies power to channels 1-3 and line cord 2 to channels 4-6.
Operation Guide
8
Press the MENU button until the "Dimmer/Switch"
LED illuminates. The display will read either "
LED illuminates. The display will read either "
" or "
" depending on the current
setting. The "C" indicates "Channel". The number
that follows is the pack's channel number. The "d"
indicates "Dim" and "S" indicates "Switch". In the
example to the left, it shows channel 1 is
currently set to dim.
that follows is the pack's channel number. The "d"
indicates "Dim" and "S" indicates "Switch". In the
example to the left, it shows channel 1 is
currently set to dim.
Function Mode 4: Dimmer/Switch
DMX Signal
DMX Address
Patch Address
Local Control
Dimmer / Switch
MENU
PANIC
1
2
3
4
5
6
OK
1
2
3
4
5
6
MD
ON
6
5
4
3
2
1
(2) Press the UP/ Down button to change the
current setting. d="Dim"/s="Switch"
(3) Press "OK" button to confirm and save your
setting. The display will momentarily flash
confirming that your setting was stored.
Repeat steps 1, 2 and 3 to assign additional
channels. These settings will be stored to
memory.
Repeat steps 1, 2 and 3 to assign additional
channels. These settings will be stored to
memory.
DMX Signal
DMX Address
Patch Address
Local Control
Dimmer / Switch
MENU
PANIC
1
2
3
4
5
6
OK
1
2
3
4
5
6
MD
ON
6
5
4
3
2
1
Select the channel that you wish to assign by
selecting from buttons 1-6. Only one channel
can be assigned at a time.
can be assigned at a time.
(1)
DMX Signal
DMX Address
Patch Address
Local Control
Dimmer / Switch
MENU
PANIC
1
2
3
4
5
6
OK
1
2
3
4
5
6
MD
ON
6
5
4
3
2
1
DMX Signal
DMX Address
Patch Address
Local Control
Dimmer / Switch
MENU
PANIC
1
2
3
4
5
6
OK
1
2
3
4
5
6
MD
ON
6
5
4
3
2
1
This menu option allows you to set the pack's channels to dim or switch. Each
channel can be individually set to do one or the other. When a channel is set to
switch, then that channel will activate when the channel level exceeds 50%.
When a channel is set to dim, then that channels intensity can manually
be adjusted from 0 to 100%.
channel can be individually set to do one or the other. When a channel is set to
switch, then that channel will activate when the channel level exceeds 50%.
When a channel is set to dim, then that channels intensity can manually
be adjusted from 0 to 100%.