Accusplit AE1720 Leaflet

•  step: STEP mode shows your 

step count since last reset, up  

to 100,000 steps. 

shows total activity time in 

minutes and seconds since  

last reset. The timer runs 

automatically whenever steps  

are being recorded.

Adjusting your Pedometer’s 
Measurement Sensitivity AE1700 

pedometers are highly accurate step 

counters. However, some walkers may 

find that their step counts tend to be 

a bit too high, or too low. All AE1700 

models come with a sensitivity adjust-

ment, to help account for individual 

differences. The adjustment switch has 

three positions: “+,” “-,” and center. 

The adjustment switch is located on the 

bottom of the pedometer, on the right-

hand side when looking from the front.

Adjustment Procedure: Take 100 steps, 

then check STEPS display to see how 

many steps were actually counted. 

Repeat once to make sure results are 

about the same. If the pedometer counts 

fewer steps than you actually walked, 

slide the sensitivity adjustment towards 

the “+” icon. This will increase recorded 

steps by about 10%. If the pedometer 

counts more steps than you actually 

walked, slide the sensitivity adjustment 

towards the “-” icon. This will decrease 

recorded steps by about 10%.

While gently holding the belt clip open, 

slide the pedometer onto your belt or the 

top edge of your pants or skirt. It should 

fit snugly and level, above one knee. 

Note: The pedometer should be as 

vertical as possible. Walkers with larger 

stomachs may find it helpful to wear the 

pedometer farther back on the body, 

toward one hip. The cover must be 
closed for the pedometer to work. To 

avoid losing or dropping your pedometer, 

use the included leash and clip to fasten 

the pedometer securely to your clothing. 

Attaching the Leash: Attach the 

pedometer to the leash by looping the 

leash through the pedometer leash slot. 

Next, loop the leash through the metal 

clip. Finally, clasp the waistband of your 

clothing with the metal clip. You can also 

use a safety pin to fasten the leash to 

your clothing, loop the leash through your 

belt or belt loop, or use a badge holder. 

ACCUSPLIT, Inc.  •  6120 Stoneridge Mall Rd., Suite 210  •  Pleasanton, CA 94588 USA

800-965-2008  •  925-226-0888  •  FAX 925-463-0147  •  www.ACCUSPLIT.com  •  support@ACCUSPLIT.com

Most people prefer to reset step counts 

daily. To reset: press and hold the white 

RESET button for at least 2 seconds.

When the display starts to dim or goes 

blank, it is time to replace the battery. 

Your pedometer uses one Type L1142 

(LR43) 1.5 volt silver oxide battery.  

To replace:

1. Insert a coin into the slot on the front  

  of the case, and twist counterclock- 

  wise to loosen the battery door.
2. Remove battery door and take out the  

  old battery. Replace it with a new  

  battery. The battery’s positive (+)  

  terminal should be FACE UP while you  

  put it into the pedometer.
3. Put the battery door back on and twist  

  the coin clockwise to tighten.

Congratulations on taking the first step to wellness 

with your purchase of an ACCUSPLIT pedometer. 

It’s easy to set up your new pedometer. 

Just follow the steps below, and start walking!

Red: 

MODE

ACCUSPLIT 

EAGLE

White: 

RESET 

970-051

(Badge holder  

not included)

Once you put on your pedometer with the 

cover closed, it will automatically begin 

to record your steps, and activity time. 

Repeatedly press the red MODE button to 

cycle through the pedometer modes: 

STEP → ACTIVITY TIMER → STEP