JL Audio SB-F-FCSZX/10W3v3 User Manual
➔
➔
➔
➔
➔
Stealthbox
®
I N S TA L L AT I O N G U I D E
S B - F - Z X 3 / 1 0 W 3 , J L AU D I O, I n c 2 0 0 2
S h e e t S K U # 0 1 1 1 5 7 R ev i s i o n 0 6 / 1 8 / 0 2
Pa g e 1
(2000-Up ZX3 2-door & 2001-Up ZX5
4-door hatchback)
SB-F-ZX3/10W3
for the
This Stealthbox is a product that
requires professional installation skills
and tools.
Please read this installation guide
thoroughly before beginning the
project. It will guide you step by step
through the installation. Several of
the steps in this process may require
two people to accomplish.
and tools.
Please read this installation guide
thoroughly before beginning the
project. It will guide you step by step
through the installation. Several of
the steps in this process may require
two people to accomplish.
It is absolutely vital that the
enclosure be properly mounted to
the vehicle according to these
instructions. Failure to mount the
enclosure properly presents two
problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused
by the force exerted by the
woofer(s) and 2) A loose enclosure
presents a serious safety hazard in
the event of a collision or sudden
deceleration.
the vehicle according to these
instructions. Failure to mount the
enclosure properly presents two
problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused
by the force exerted by the
woofer(s) and 2) A loose enclosure
presents a serious safety hazard in
the event of a collision or sudden
deceleration.
Please enjoy your JL Audio
Stealthbox responsibly.
STEP 1: Remove the four Phillips head
screws, panel button and cargo light from
driver’s side rear cargo area.
screws, panel button and cargo light from
driver’s side rear cargo area.
STEP 2: Remove the plastic safety belt
retractor cover. Look up under the plastic
cover for a Phillips head screw. Remove this
screw. (The location of this screw is shown in
the picture by the upward arrow).
retractor cover. Look up under the plastic
cover for a Phillips head screw. Remove this
screw. (The location of this screw is shown in
the picture by the upward arrow).
STEP 3: Remove the two plastic Phillips head
screws indicated by the arrows.These are
located in the driver’s rear hatch plastic trim
panel. Remove the carpeted side panel.This
panel will be cut in Step 9 so as to form a
trim for the Stealthbox.The view shown
above is from the back seat looking toward
the hatch. Also remove the hatch flooring (this
flooring will be re-installed later).
screws indicated by the arrows.These are
located in the driver’s rear hatch plastic trim
panel. Remove the carpeted side panel.This
panel will be cut in Step 9 so as to form a
trim for the Stealthbox.The view shown
above is from the back seat looking toward
the hatch. Also remove the hatch flooring (this
flooring will be re-installed later).
STEP 4: Locate the MOLEX
®
plug and pull it
loose from the side panel.
STEP 5: Remove the T-27 TORX head bolt
from the back side of the driver’s side rear
wheel well. Remove the Phillips screw from
directly below the TORX head bolt.
from the back side of the driver’s side rear
wheel well. Remove the Phillips screw from
directly below the TORX head bolt.
STEP 6: Loosen the driver’s side rear fabric
wheel well by pulling it toward the front of
the car.
wheel well by pulling it toward the front of
the car.
.
START
HERE
Continued on Page 2
➔
w w w . j l a u d i o . c o m
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔