Yamaha RX-V395 User Manual
41
English
Returning to the factory-set
codes
codes
To return all components to the factory-set
codes, follow these steps.
1. Press a component selector button
codes, follow these steps.
1. Press a component selector button
other than AMP<TUNER>.
2. Press both VOLUME buttons (
)
for about four seconds at the same
time so that the indicator flashes
twice.
time so that the indicator flashes
twice.
3. Enter the code number “9990”.
4. Make sure that the indicator flashes
4. Make sure that the indicator flashes
twice.
To return each component to the factory-
set codes, follow these steps.
1. Press the component selector that
set codes, follow these steps.
1. Press the component selector that
matches the component to be
returned to the factory-set codes.
returned to the factory-set codes.
2. Press both VOLUME buttons (
)
at the same time for about four
seconds so that the indicator flashes
twice.
seconds so that the indicator flashes
twice.
3. Enter the code number “0000”.
4. Make sure that the indicator flashes
4. Make sure that the indicator flashes
twice.
The following codes are preset by the
factory.
factory.
Factory-set codes
We recommend that you write all code
numbers you have preset on the “Quick
Reference Card”.
numbers you have preset on the “Quick
Reference Card”.
To control your components
(MD recorder, DVD player, TV,
etc.)
(MD recorder, DVD player, TV,
etc.)
1. Turn on the component to be used.
2. Press the component selector button
2. Press the component selector button
that matches the component to be
controlled (TAPE/MD, DVD/LD, TV
etc.).
controlled (TAPE/MD, DVD/LD, TV
etc.).
3. Press both VOLUME buttons (
)
at the same time for about four
seconds so that the indicator flashes
twice.
seconds so that the indicator flashes
twice.
4. Use the numeric buttons to enter the
four-digit manufacturer’s code for the
component to be used. Make sure that
the indicator flashes twice.
If the indicator does not flash, repeat
step 3 and re-enter the code.
component to be used. Make sure that
the indicator flashes twice.
If the indicator does not flash, repeat
step 3 and re-enter the code.
5. Press POWER (or any other button)
on the remote control transmitter to
check if you have preset the code
correctly. If the component cannot be
controlled by the remote control
transmitter, try entering another code
for the same manufacturer.
check if you have preset the code
correctly. If the component cannot be
controlled by the remote control
transmitter, try entering another code
for the same manufacturer.
Presetting the remote control transmitter
Perform the presetting procedure for each component you want to control with the remote control transmitter.
Note
If your component does not respond to any of the codes listed for the manufacturer, use the original remote control transmitter that
was supplied with the component.
Note
If your component does not respond to any of the codes listed for the manufacturer, use the original remote control transmitter that
was supplied with the component.
To use a second (and third)
VCR
VCR
You can control a second (and/or third)
VCR in the CBL/DBS and DVD MENU
modes if a CBL (or DBS) or DVD player is
not being used.
VCR in the CBL/DBS and DVD MENU
modes if a CBL (or DBS) or DVD player is
not being used.
If you want to control a second (and/or
third) VCR in the DVD MENU mode, you
must preset the code for an LD player in
that mode.
third) VCR in the DVD MENU mode, you
must preset the code for an LD player in
that mode.
1. Turn on the VCR to be used.
2. Press the component selector button
2. Press the component selector button
CBL/DBS or DVD MENU.
3. Press both VOLUME buttons (
)
at the same time for about four
seconds so that the indicator flashes
twice.
seconds so that the indicator flashes
twice.
4. Use the numeric buttons to enter the
four-digit code for the second (or third)
VCR. Make sure that the indicator
flashes twice. If the indicator does not
flash, repeat step 3 and re-enter the
code.
VCR. Make sure that the indicator
flashes twice. If the indicator does not
flash, repeat step 3 and re-enter the
code.
5. Press POWER (or any other button)
on the remote control transmitter to
check if you have preset the code
correctly. If the VCR cannot be
controlled by the remote control
transmitter, try entering another code
for the same manufacturer.
check if you have preset the code
correctly. If the VCR cannot be
controlled by the remote control
transmitter, try entering another code
for the same manufacturer.
SETUP CODES
2CH
6CH
Component
Component
Code
selector
TV
TV
0101
CBL/DBS
DBS tuner
0006
VCR
VCR
0002
DVD/LD
DVD player
0008 YAMAHA
CD
CD player
0005 YAMAHA
TAPE/MD
Tape deck
0004 YAMAHA
2CH
6CH