Rocketfish RF-TVMFM02 Leaflet

 

1  Align the TV bracket (A) with the screw holes on the back of the TV.

 

2  Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV bracket, 

 

 

then insert the M4 screws (F), M5 screws (J), or M6 screws (L or M) through the washers.

 

3  Tighten the screws until they are snug against the TV bracket. Do not over tighten.

 Note: Any material covering the wall must not exceed 5/8 in. (16 mm).
 

 

1  Locate the stud. Verify the center of the stud with an awl 

 

 

or thin nail or use an edge-to-edge stud finder.

 

2  Level the arm assembly (B) and mark the hole locations.

 

3  Drill pilot hole to a depth of 3 in. using a 7/32 in. diameter drill bit.

 

4  Align the arm assembly (B) with the pilot holes.

 

5  Place the washers (D) over the holes in the 

 

 

arm assembly, insert the lag bolts (E) 

 

 

through the washers, then tighten 

 

 

the lag bolts only until the washers 

 

 

are pulled firmly against the arm 

  assembly. 
CAUTION: Avoid potential injuries or 
property damage!
DO NOT over-tighten the lag bolts (E).

 Note: Use additional washers (H) with M4/M5 hardware only.
 

1  Align the TV bracket (A) with the screw holes on the back of the TV.

 

2  Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV bracket, 

 

 

then insert the M4 screws (G), M5 screws (K), or M6 screws (N or Q) through the washers.

 

3  Tighten the screws until they are snug against the TV bracket. Do not over tighten.

 

1  Level the arm assembly (B) and mark the hole locations.

 

2  Drill pilot hole to a depth of 3 in. using a 3/8 in. diameter drill bit.

 

3  Insert the concrete wall anchors (C) into the pilot holes 

 

 

and make sure that the anchors are seated flush with 

 

 

the concrete surface.

 

4  Align the arm assembly (B) with the anchors. 

 

5  Place the washers (D) over the holes in the arm assembly, 

 

 

insert the lag bolts (E) through the washers, then tighten 

 

 

the lag bolts only until the washers (D) are pulled firmly 

 

 

against the arm assembly. 

CAUTION: Avoid potential injuries or property damage!
DO NOT over-tighten the lag bolts (E).

Tools you will need:
• Stud 

finder

• Awl
• Pencil
• Level
• Tape 

measure

• Phillips 

screwdriver

•  Hammer (concrete only)

• Socket 

wrench 

with 

 

1/2 in. socket or 

 adjustable 

wrench

•  7/32 in. wood drill bit
•  3/8 in. masonry drill bit
 (concrete 

only)

• Power 

drill

A  TV bracket (1)
B  Arm assembly (1)
Lag bolt bag
C  Concrete anchor (2)
D  Lag bolt washer (2)
E  5/16 in. × 2-3/4 in. lag bolt (2)
M4 bag
F  M4 × 12 mm screws (4)
G  M4 × 30 mm screws (4)
H  M4/M5 washers (8)
I  M4/M5 spacers (4)
M5 bag
J  M5 × 12 mm screws (4)
K  M5 × 30 mm screws (4)

Thank you for choosing the Rocketfish RF-TVMFM02. 
The RF-TVMFM02 TV mount is designed to support a 
flat-panel TV weighing up to 60 lbs. (27.2 kg).

M6 bag
L  M6 × 12 mm screws (4)
M  M6 × 20 mm screws (4)
N  M6 × 35 mm screws (4)
O  M6/M8 washers (4)
P  M6/M8 spacers (4)
M8 bag
Q  M8 × 40 mm screws (4)
Hex key bag
R  3/16 in. hex key (1)
S  5/32 in. hex key (1)
Cap screw
T  Cap screw (1)
Cable ties
U  8 in. nylon cable ties (5)

M4/M5

M6/M8

M6 

×

 20 mm

M6 

×

 35 mm

M6 

×

 12 mm

M4 

×

 30 mm

M4 

×

 12 mm

M5 

×

 30 mm

M5 

×

 12 mm

M4/M5

M6/M8

M8 

×

 40 mm

5/16 in. 

×

 2-3/4 in.

3/16 in.

5/32 in.

CAUTION: To prevent property 
damage or personal injury, never 
drill into mortar between blocks.
Mount wall plate directly onto the 
concrete surface.

TV shifts 7 in. from the home position 
to full extension.

C

M

Y

CM

MY

CY

CMY

K

RF-TVMFM02_10-0565_QSG_V1_EN.eps   1   6/2/2010   6:03:12 PM

RF-TVMFM02_10-0565_QSG_V1_EN.eps   1   6/2/2010   6:03:12 PM