Dynex DX-TVM111 Leaflet

Slim-Profile TV Mount

DX-TVM111

Thank you for choosing the Dynex DX-TVM111. 
The DX-TVM111 TV mount is designed to support 
a TV weighing up to 30 lbs. (13.6 kg).

A  Wall plate (1)
B  TV bracket (1)
C Locking bar (1)
M4 Bag
  D  M4 × 12 mm screws (4)
  E  M4 × 30 mm screws (4)
 F 

M4 

spacers 

(4)

  G  M4 washers (4)
Lag Bolt Bag
 H 

Concrete 

wall 

  anchors 

(2)

  I  1/4 in. × 2½ in. 
  lag 

bolts 

(2)

NOTE: Make sure there will be enough space between the back of the TV and 

  the wall to connect all your cables.
  You can use the optional M4 spacers to provide additional space.
  Without spacers: Attach the TV bracket (B) 
  to the back of the TV using 
  the M4 washers (G) 
  and the M4 × 12 mm 
 screws 

(D).

  With spacers: Attach 
  the TV bracket (B) to the
  back of the TV using the
  M4 spacers (F), M4 
 washers 

(G), 

and 

  M4 × 30 mm screws (E).
NOTE: You can mount the 
TV vertically or at an angle 
(tilt mount). See Step 3 
for more information.

• Power 

drill

•  1/8 in. wood drill bit
•  ½ in. masonry drill bit
• Phillips 

screwdriver

• Level
•  Socket wrench with 
  7/16 in. socket or 
 adjustable 

wrench

• Pencil
• Stud 

finder

• Awl

1/4 in. × 2½ in.

M4

  Option 2: Installing to a concrete wall
  1  Level the wall plate (A) and mark the hole locations.
  2  Drill the pilot holes as illustrated.
  3  Insert the concrete wall anchors into the pilot holes and make sure that 
   

the anchors (H) are seated flush with the surface.

  4  Align the wall plate with the anchors, insert the lag bolts (I) through the 
   

holes in the wall plate, then tighten the lag bolts (I) only until they are

   

pulled firmly against the wall plate (A). 

   

DO NOT over-tighten the lag bolts (I).

CAUTION: Avoid potential injuries or property damage!
Any material covering the wall must not exceed 5/8 in. (16 mm).

CAUTION: To prevent property damage or personal 
injury, never drill into mortar between blocks.

  Option 1: Installing to a wood stud wall
  1  Locate the stud. Verify the center of the stud with an awl or thin nail or  
   

use an edge to edge stud finder.

  2  Level the wall plate (A) and mark the hole locations.
  3  Drill the pilot holes as illustrated.
  4  Align the wall plate with the pilot holes, insert the lag bolts (I) through the 
   

holes in the wall plate, then tighten the lag bolts only

   

until they are pulled firmly against the wall plate (A). 

   

DO NOT over-tighten the lag bolts (I).

CAUTION: Avoid potential injuries or property damage!
Any material covering the wall must 
not exceed 5/8 in. (16 mm).

5/8 in.

(<16 mm)**

2.5 in.

(63.5 mm)*

M4 × 12 mm

M4 × 30 mm

M4

5/8 in.

(<16 mm)

*Drill the pilot hole to a 

depth of 2.5 in. (63.5 mm)

2.5 in.

(63.5 mm)*

*Drill the pilot hole to a depth of 2.5 in. (63.5 mm)
**Maximum thickness of any material covering 
  the stud or concrete surface.