Panasonic FV-05-11VKSL1 User Manual
2. Remove the screw as shown in step of Fig.21.
Remove the light cover as shown in step of Fig.21.
Remove the light cover as shown in step of Fig.21.
MAINTENANCE (REPLACEMENT OF LAMP)
1. Clean grille. (Don’t put into hot water. Use non-abrasive
kitchen detergent, wipe dry with clean cloth) (Fig.17)
kitchen detergent, wipe dry with clean cloth) (Fig.17)
2. The grille should be dry after cleaning.
3. Remove dust and dirt from fan body using a vacuum
cleaner. (Fig.18)
4. Using a cloth dampened with kitchen detergent, remove
any dirt from fan body. Wipe dry with clean cloth. (Fig.19)
5. Reinstall grille.
3. Remove dust and dirt from fan body using a vacuum
cleaner. (Fig.18)
4. Using a cloth dampened with kitchen detergent, remove
any dirt from fan body. Wipe dry with clean cloth. (Fig.19)
5. Reinstall grille.
Disconnect power source before working on unit.
Routine maintenance must be done every year.
Please wear gloves during the cleaning work.
Please wear gloves during the cleaning work.
Never use gasoline, benzene, thinner or any other
such chemicals for cleaning the ventilating fan.
such chemicals for cleaning the ventilating fan.
Disconnect power source before working on unit.
The lamp’s glass is fragile, be careful when the lamp
is replaced.
Make sure the temperature of lens and lighting
unit has cooled down before maintenance
(cleaning) or replacement of lamp.
The lamp’s glass is fragile, be careful when the lamp
is replaced.
Make sure the temperature of lens and lighting
unit has cooled down before maintenance
(cleaning) or replacement of lamp.
Do not immerse motor in water when cleaning.
Do not soak resin parts in water over 140 F (60 C).
Do not soak resin parts in water over 140 F (60 C).
WARNING
CAUTION
4. Install the
LED lamps (CX-GU24-H-B, 7W) as shown in
step 1 and step 2 of Fig.9 (Page 9).
WARNING
Remove dust and dirt from light cover and lens,
before replace the lamps.
before replace the lamps.
The LED lamps should be replaced as the specified
type. The supplied LED lamps are not intended for
other use.
type. The supplied LED lamps are not intended for
other use.
CAUTION
3. Replace the LED lamps (CX-GU24-H-B, 7W) as shown in
step 1 and step 2 of Fig.22.
step 1 and step 2 of Fig.22.
Fig.17
Fig.18
Fig.19
11
5. Install light cover. (Fig.10 of page 9)
1. Remove grille by pulling down one mounting spring
(Fig.20). Remove plug connector then pull down the other.
(For models plug-in FV-MSVK1 or FV-NLVK1: Pull down the
mounting spring that without lead wire passed side, and
remove motion sensor or LED night light as shown in Fig.20)
(Squeeze mounting spring and pull down carefully)
(Fig.20). Remove plug connector then pull down the other.
(For models plug-in FV-MSVK1 or FV-NLVK1: Pull down the
mounting spring that without lead wire passed side, and
remove motion sensor or LED night light as shown in Fig.20)
(Squeeze mounting spring and pull down carefully)
Gloves
Gloves
Vacuum
cleaner
cleaner
MAINTENANCE (CLEANING)
Ceiling
Ceiling
Remove screw
(M4X8)
(M4X8)
Light cover
Fig.22
Fig.21
LED lamp
Lens
Fig.20
Plug
connector
connector
Gloves
Grille
LED night light
(FV-NLVK1 only)
(FV-NLVK1 only)
Clasp
Lighting
unit
unit
Motion sensor
(FV-MSVK1 only)
(FV-MSVK1 only)
Mounting spring
Ceiling
Remove
plug
connector
plug
connector
Rib
Claw