RCA RCRN06GR Leaflet

In most cases, the keys on this remote 

perform the same functions as the keys 

on your original remotes once you’ve 

programmed this remote to operate your 

components. Many keys on this remote 

have other functions as well.
Illuminated POWER key serves as an 

indicator light to provide feedback.
Device keys (TV, SAT•CBL•DTC, DVD, 

AUDIO, DVR•AUX1, VCR•AUX2) put the 

remote in the right mode to control your 

device.
Backlight key (

) turns backlighting on/

off.
GUIDE and MENU put the remote in menu/

guide mode; they also access the same 

features as the keys on your original 

remotes.
EXIT exits remote programming; it also 

performs the same functions as on your 

original remotes.
Arrow keys act as navigation keys in 

device guides and menu systems.
OK key selects your menu choices.
The MACRO key, along with the number 

keys 1–8, let you store and execute multi-

step actions (macros) in a single keypress
The INPUT and — (dash) key has three 

functions: (1) it toggles through all the 

video or audio sources connected to your 

TV or audio device; (2) when the remote is 

in VCR mode, this button toggles between 

VCR and the TV input; (3) when you’re 

entering digital channel numbers directly, 

this button lets you separate the main 

channel number from the sub-channel 

number (such as 59.1).

Your universal remote control saves battery power by automatically turning off if 

any key is pressed for more than 60 seconds. This saves your battery life should 

your remote get stuck in a place where the keys remain depressed, such as 

between sofa cushions.

•  Keep the remote dry. If it gets wet, wipe it dry immediately.
•  Use and store the remote only in normal temperature environments.
•  Handle the remote gently and carefully. Don’t drop it.
•  Keep the remote away from dust and dirt.
•  Wipe the remote with a damp cloth occasionally to keep it looking new.
•  Modifying or tampering with the remote’s internal devices can cause malfunction 

and invalidate its warranty.

Your universal remote requires three AAA alkaline batteries (not included).

  Remove the battery compartment cover.

 Insert the batteries, matching the (+) and (–) marks 

inside the battery compartment.

 Push the battery cover back into place.

To use this universal remote with your home entertainment system, first you need 

to program it to control your devices. There are four ways you can program the 

universal remote to operate your devices: 

• 

The Auto Code Search goes automatically through all the codes for the 

device you’re trying to control. It’s the easiest method, but it can sometimes 

take longer than some of the other programming methods. 

•   The Brand Code Search searches through the codes for select brands of 

devices. It’s not as easy as the auto code search, but it can be faster.

•   The Direct Code Entry lets you enter a code from the accompanying code 

list for your brand of device. It’s not as easy as the other methods, but it’s 

potentially the fastest method. Note: Direct Code Entry is usually the best 

method to use for audio devices.

•   The Manual Code Search lets you manually go through all the codes for 

the device you’re trying to control

.

Testing the Code for Maximum Functionality
1.  Try a variety of the device’s functions with the remote. If some device 

features don’t work, go to the next step to try a different code.

  Repeat the Auto Code Search Method from the beginning. When your device 

turns off, do not stop searching. Instead, with the unit now off, continue to 

press the SLOW key every 5 seconds until the unit turns back on. 

3.   Once the unit turns back on, press the SKIP BACK key on the remote every 2 

seconds until your device turns off again. When your device turns off again, 

press the OK key. 

4.   Test the key’s functionality again by attempting to control a variety of the 

device’s functions. If the code that has been stored controls the majority of 

the device’s functions, programming is complete. If the code stored does not 

give maximum functionality, try another code.

The Auto Code Search goes automatically through all the codes for the device 

you’re trying to control. When you find the one that operates your device, you 

can stop the search and store that code. 

the Reassigning the DVR•AUX1 or VCR•AUX2 key section.
To control combo devices, like TV/DVDs and TV/VCRs, you need to program each 

  Manually turn on the device you want to control. 

  Press and hold the device key you want to program 

(the POWER key illuminates). While you’re holding 

down the device key, use your other hand to press 

and hold the remote’s POWER key at the same time 

(the POWER key turns off).

  Wait until the POWER key comes on and stays on. 

Then release both keys.

  Point the remote directly at the front panel of the 

device you want to control. Press SLOW on the remote 

and wait 5 seconds. The remote is testing a batch of 10 

codes on your device.

YES: Go to step 5.

NO: Press SLOW again. The remote tests the next 

batch of 10 codes. 

 

Keep pressing SLOW every 5 seconds until your device 

turns off. 

When your device turns off, press the SKIP BACK 

key on the remote and wait at least 2 seconds. The 

remote tries the last of the previous ten codes. 

 

YES: Press the OK key. You’re done! You’ve 

programmed this device key.

NO: Press SKIP BACK again. The remote tests the 

next code in the batch. 

 

Keep pressing SKIP BACK every 2 seconds until your 

device turns back on. When it does, press OK.

  Try a variety of the device’s functions with the remote. If some device 

features don’t work, go to the next step to try a different code.

2.   Repeat the Brand Code Search from the beginning. When the device turns 

off for the first time, don’t press the OK key, which would store the same 

code. Instead, with the unit now off, continue to press the SKIP FWD key 

repeatedly until the unit turns back on.

  Once the unit turns back on, you have found another code that operates the 

device. Press the OK key.

4.   Test the key’s functionality again by attempting to control a variety of the 

device’s functions. If the code that has been stored controls the majority of 

the device’s functions, programming is complete. If the code stored does not 

give maximum functionality, try another code.

The Brand Code Search goes through only the codes for one of the select brands 

listed in the accompanying code list. If your brand of device is listed, this search 

can be very quick and easy. 

the Reassigning the DVR•AUX1 or VCR•AUX2 key section.
To control combo devices, like TV/DVDs and TV/VCRs, you need to program each 

  Manually turn on the device you want to control. 

  Press and hold the device key you want to program 

(the POWER key illuminates). While you’re holding 

down the device key, use your other hand to press 

and hold the remote’s POWER key at the same time 

(the POWER key turns off).

  Find your device’s brand in the Brand Code list 

section of the accompanying code list. Circle the 

number for your brand and keep the list handy. 

  Wait until the POWER key comes on and stays on. 

Then release both keys.

  Look at the numbers you circled for your device’s 

brand code. Press those numbers on the remote 

keypad.

Direct Code Entry lets you enter a code from the accompanying code list for your 

brand of device. It’s not as easy as the other methods, but it’s potentially the 

fastest method.

the Reassigning the DVR•AUX1 or VCR•AUX2 key section.
To control combo devices, like TV/DVDs and TV/VCRs, you need to program 

  Manually turn on the device you want to control. 

  Press and hold the device key you want to program 

(the POWER key comes on). 

 

While you’re holding down the device key, use your 

other hand enter the first five-digit code for your brand 

in the code list (the POWER key goes off after the first 

digit).

  Find the Code List that came with the remote. Locate 

the section for the type of device you’re trying to 

program, and find your brand in that section. Circle 

the codes for your brand and keep them handy. 

  When you’ve finished entering the five-digit code, keep holding down the 

device key and look at the POWER key. 

YES: You’re done! You’ve programmed this device key.

NO, it blinked four times and turned off: You have either entered a 

code number that is not in the code lists or missed a step in the code entry 

procedure. Try step 3 again. 

The Manual Code Search takes you one-by-one through all the codes for the device 

you’re trying to control. When you find the one that operates your device, you stop 

the search and store that code.

the Reassigning the DVR•AUX1 or VCR•AUX2 key section.
To control combo devices, like TV/DVDs and TV/VCRs, you need to program each 

 

  Manually turn on the device you want to control. 

  Press and hold the device key you want to program 

(the POWER key illuminates). While you’re holding 

down the device key, use your other hand to press 

and hold the remote’s POWER key at the same time 

(the POWER key turns off).

  Wait until the remote’s POWER key comes on and 

stays on. Then release both keys.

  Point the remote directly at the front panel of the 

device you want to control. Press SKIP FWD on the 

remote and wait 2 seconds. The remote is testing a 

single code for your device.

 

YES: Press the OK key to store the code. You’re 

done! You’ve programmed this device key.

NO: Press SKIP FWD again. The remote tests the 

next code for your device. 

 

Keep pressing SKIP FWD every 2 seconds until your 

device turns off. When it does, press OK.

 

Testing the Code for Maximum Functionality
1.   Try a variety of the device’s functions with the remote. If some features of 

your devices don’t work, go to the next step to try a different code.

2.   Repeat the Manual Code Search and Entry Method from the beginning. 

When the device turns off for the first time, don’t press the OK key, which 

would store the same code. Instead, with the unit now off, continue to press 

the SKIP FWD key repeatedly until the unit turns back on. 

3.   Once the unit turns back on, you have found another code that operates the 

device. Press the OK key.

4.   Test the key’s functionality again by trying a variety of functions. If the code 

controls the majority of the device’s functions, programming is complete. If 

the code stored does not give maximum functionality, try another code.

The DVR•AUX1 key defaults to control a DVR, and the VCR•AUX2 key defaults to 

control a VCR. If you want the DVR•AUX1 or VCR•AUX2 key to control a different 

device (an additional TV, DVD, satellite or cable box, for example), you must 

reassign it.
1.   Press and hold the DVR•AUX1 or VCR•AUX2 key. The POWER key turns on.
2.   While holding down the DVR•AUX1 or VCR•AUX2 key, press and release the 

number key on the keypad for the device you wish to control (see the chart 

below). The POWER key turns off.

Once you’ve programmed the remote to control your devices, you may want to 

record the codes for future reference. If you used the Direct Code Entry method, 

this is easy. Just find the codes you entered and make a note of them in the 

boxes below. If you used one of the Code Search methods to program your 

remote or if you used the Direct Entry method but don’t remember the code, you 

will need to retrieve each device’s five-digit code. Retrieving the actual code and 

writing it down will save you time if you ever need to program the remote again. 

If the codes are recorded, you can use the Direct Entry method to reprogram 

your remote to control your devices, which is quick and easy.

1.   Press and hold the device key (TV, SAT•CBL•DTC, DVD, AUDIO, DVR•AUX1 

or VCR•AUX2) whose code you wish to retrieve. The POWER key illuminates. 

Keep pressing the device key.

2.   While holding the device key down, press and hold the INFO key. The 

POWER key illumination turns off. After holding down both keys for three 

seconds, it turns back on.

3.   Release both keys. The POWER key remains illuminated.
4.   Starting with the number 1 key, press and release each number key on the 

keypad in the following order: 1-9, then 0. The number that causes the POWER 

key to blink is the first number of the code. As you find each number of the 

code, write it down for future reference. Then start with the number 1 key again.

5.   Repeat step 4 until you have retrieved all five numbers in the code. After the 

fifth number is retrieved, the POWER key blinks briefly, then turns off.

Problem: The remote does not operate your device.
•  

Make sure the remote is in the correct mode by pressing the corresponding device 

key (TV, SAT•CBL•DTC, DVD, AUDIO, DVR•AUX1, VCR•AUX2). This tells the remote 

which device to operate.

•  

Remove any obstacles between the remote and the device. Make sure you’re aiming 

the remote at the device’s IR sensor.

•  

Make sure the batteries are fresh and are properly installed. Replace the batteries 

with three new AAA batteries, if necessary (see the Battery Installation section). 

Problem: The remote can’t be programmed to operate your device.
•  

If you are testing the remote while programming it, you may be too far away from the 

device or at a wrong angle. There must be an unobstructed path between the remote 

and the IR sensor on the device. Move closer and make sure you point the remote at the 

device you’re trying to control.

•  

If you’re using the Direct Entry programming method to enter the codes for your 

brand and the unit is still not functioning properly, try the auto, brand, or manual 

search method.

•  

To control combo units, like TV/VCRs or TV/DVDs, you must program the 

individual corresponding device keys to control each part of the combo unit. Once 

programmed successfully, the TV key controls the TV functions, and the DVD or 

VCR•AUX2 key controls the DVD or VCR functions. 

•  

Make sure the batteries are fresh and are properly installed.

Problem: The remote doesn’t perform commands properly.
•  

Make sure the remote is in the correct mode by pressing the corresponding device 

key (TV, SAT•CBL•DTC, DVD, AUDIO, DVR•AUX1, VCR•AUX2). This tells the remote 

which device to operate.

•  

Make sure device is ready (for example, the DVD player has a disc loaded).

•  

You may have pressed an invalid key for the mode the remote is in.

•  

If you’re trying to enter a channel number directly, try pressing the ENTER key after 

entering the channel number as this is a requirement of certain models and brands.

•  

There is a possibility that a programmed code may only be able to control some of 

your device features (for example, only turns a device on and off). To confirm that 

the device key is programmed with the correct code for maximum functionality, test 

the device. Attempt to control a variety of the device’s functions with the remote. If 

some of the features of your devices don’t work, try programming the remote with a 

different code in the list using the Direct Code Entry Method, until you find the code 

that allows the remote to control the majority of your device’s functions. Different 

codes can provide different levels of functionality.

Problem: The POWER key does not illuminate when you press a key.
•  

You may have pressed an invalid key for the mode the remote is in. 

• 

Make sure the remote is in the correct mode by pressing the corresponding device 

key (TV, SAT•CBL•DTC, DVD, AUDIO, DVR•AUX1, VCR•AUX2). This tells the remote 

which device to operate.

•  

Make sure the batteries are fresh and are properly installed. Replace the batteries 

with three new AAA batteries, if necessary (see the Battery Installation section). 

Problem: The remote will not change channels on device.
• 

Make sure the remote is in the correct mode by pressing the corresponding device 

key (TV, SAT•CBL•DTC, DVD, AUDIO, DVR•AUX1, VCR•AUX2). This tells the remote 

which device to operate.

•  

Press the ENTER key after you enter a channel number.

•  

Remove any obstacles between the remote and the device. Make sure to aim the 

remote at the IR sensor on the device.

Problem: The device’s menu does not appear on the TV screen.
•  

Make sure you have connected the device to your TV properly and selected the correct 

input. (See your devices’ Owner’s Manuals for proper connection procedures.)

• 

Make sure the remote is in the correct mode by pressing the corresponding device 

key (TV, SAT•CBL•DTC, DVD, AUDIO, DVR•AUX1, VCR•AUX2). This tells the remote 

which device to operate.

•  

Menu access isn’t supported for all brands. You may need to use your original 

remote control to access menu functions for some devices. 

Problem: The Learning process cannot be completed successfully.
• 

Replace batteries in both the learning remote and the original remote.

• 

Make sure the distance between the remotes is approximately 1–2 inches.

• 

Do not conduct the Learning process near an incandescent lamp.

• 

The learning remote’s memory capacity may be full (50 Learned commands).

• 

The original remote may not be compatible with the Learning procedure.

Audiovox Electronics Corporation (the “Company”) warrants to you the original retail purchaser 

of this product that should it, under normal use and conditions, be proven defective in material or 

workmanship during its lifetime while you own it, such defect(s) will be repaired or replaced (at the 

Company’s option) without charge for parts and repair labor. To obtain repair or replacement within 

the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. 

dated bill of sale), specification of defect(s), transportation prepaid, to the Company at the address 

shown below. 
This Warranty does not cover product purchased, serviced or used outside the United States or 

Canada. This Warranty is not transferable and does not extend to costs incurred for installation, 

removal or reinstallation of the product. This Warranty does not apply if in the Company’s opinion, 

the product has been damaged through alteration, improper installation, mishandling, misuse, 

neglect, accident, or the simultaneous use of different battery types (e.g. alkaline, standard or 

rechargeable).
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR 

OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY 

EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, 

INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 

PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL THE 

COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. No 

person or representative is authorized to assume for the Company any liability other than expressed 

herein in connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied warranty lasts or the 

exclusion or limitation of incidental or consequential damage so the above limitations or exclusions 

may not apply to you. This Warranty gives you specific legal rights and you may also have other 

rights, which vary from state/province to state/province.
U.S A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788 

CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,  

Unit 3, Door 16, Mississauga, Ontario  L5T 3A5

Trademark(s) ® Registered 

RCRN06GR US 00

©2010 Audiovox Accessories Corporation

Additional TV

press 1

VCR or DVR

press 2

Additional DVD

press 3

Additional audio device

press 4

Additional satellite receiver, cable box, or DTV converter

press 5

3.   Release the DVR•AUX1 or VCR•AUX2 key. The POWER key blinks four times 

and then turns off. The DVR•AUX1 or VCR•AUX2 key is now set to control 

the device type you selected.

4.   Follow the directions in the auto, brand, direct entry, or manual code search 

to program the DVR•AUX1 or VCR•AUX2 key.

Backlight illumination helps you see the remote control keys better in the dark. 

You can turn backlight illumination on or off by pressing the backlight key  

(

). Backlighting stays on as long as keys are being pressed and turns off four 

seconds after the last keypress. Once the backlight time has timed out, any 

keypress will reactivate it. If the backlight illumination is on, and you press the 

backlight key, the backlight turns off.

Transport Key Punch Through allows the transport keys (REVERSE, PLAY, 

FORWARD, RECORD, STOP, PAUSE, SKIP FWD, SKIP BACK, and SLOW), when 

pressed in TV, SAT, CABLE and AUDIO modes, to “punch through” to VCR•AUX2, 

DVR•AUX1 or DVD/CD mode, whichever was accessed last. Transport Key Punch-

Through occurs automatically and allows you to use the transport keys without 

exiting the current mode. For example, if the transport keys were last used in 

DVD mode and accessed again after pressing the TV key, they will punch through 

to the DVD. The default Transport Key Punch Through is set to DVD for TV, SAT, 

CABLE and AUDIO.
Note: Transport Key Punch Through does not occur in cases where the 

Before you start learning keys for the first time, clear any stored learning 

information that might be in the remote. This lets you begin with a clean slate.
1.  Press and hold the EXIT key (the POWER key illuminates). While you’re 

holding down the EXIT key, use your other hand to press and hold the 

POWER key (the POWER key illumination turns off).

2.  Wait until the POWER key comes on and stays on. Then release both keys. 

The remote is now in the Master Clear mode.

3.  Press the OK key to confirm the Clear operation. The POWER key remains on 

for 2 seconds, then turns off. All Learned functions for all components are 

now cleared; all other programming remains intact.

1.   Place your original remote and the learning remote on a flat surface as 

shown below. Point the top of your original remote at the top of the learning 

remote. The IR LED on the original remote should be pointing directly at 

the learning remote’s learning sensor, located on the top of the remote. The 

remotes should be 1–2 inches apart.

Codes from the Code Lists include basic functionality for each component they 

control. Once you have programmed in the code for your specific component, 

you can customize the universal remote to include certain functions from your 

original remote(s) that were not embedded in the preset code. Your universal 

remote has the ability to learn and store commands from your original remote(s) 

under the mode(s) of your choice. The universal remote can store up to 50 key 

commands.* Only one original remote can be learned under any one mode (e.g., 

the universal remote can learn commands for one TV remote, one VCR remote, 

etc.).

2.   On the learning remote, press and hold the device 

key you want to use the learned function in (the 

POWER key turns on and remains on). While 

holding down the device key, use your other hand 

to press and hold the RECORD key (the POWER key 

illumination turns off).

3.   Wait until the POWER key turns on and stays on. 

Then release both keys. The remote is now in 

Learning mode.

The Macro feature lets you execute a sequence of commands with one keypress. 

Any sequence of commands that you regularly perform (up to a maximum of 15 

per macro) can be stored as a Macro under one of the 1–8 number keys (up to 8 

macros).

  Point the remote directly at the front panel of the 

device you want to control. Press SKIP FWD on the 

remote and wait 2 seconds. The remote is testing a 

single code for your device’s brand.

YES: Press the OK key to store the code. You’re 

done! You’ve programmed this device key.

NO: Press SKIP FWD again. The remote tests the 

next code for your brand. 

 

Keep pressing SKIP FWD every 2 seconds until your 

device turns off. When it does, press OK.

Volume punch-through as described above occurs automatically. Advanced punch-

through lets you specify one device for all volume commands for each non-audio 

mode (SAT•CBL•DTC, DVD, DVR•AUX1, or VCR•AUX2). You can specify either the 

TV or AUDIO device (or an AUX key operating a TV or Audio device).
1.   Press and hold the device key whose volume commands you want to send 

to the TV or audio device. The POWER key turns on.

2.   While holding down the device key, press and hold the VOL up key. The 

POWER key turns off.

3.   After holding down both keys for 3 seconds, the POWER key turns on and 

stays on. Release both keys.

4.   Press and release the device key you want the Volume Punch-Through to be 

directed to from the selected mode (TV, AUDIO or AUX key). The POWER key 

flashes.

1.   Press the MACRO key. 
2.   Press the number key assigned to the Macro sequence you want to execute. 

The POWER key blinks once, then remains on. 

As the remote sends each command in the Macro sequence, the POWER key 

blinks once. After the remote sends the last command in the Macro sequence, 

the POWER key illumination turns off.

An Example Macro
This example shows an “all on” macro for a home theater with a TV, DVD 

player, and satellite receiver.
1. Press and hold the MACRO key until the POWER key turns on and remains on.
2. Press the 1 key to tell the remote where to store the macro.
3. Press the TV key to put the remote in TV mode.
4. Press the POWER key to turn the TV on.
5. Press the DVD key to put the remote in DVD mode.
6. Press the POWER key to turn on the DVD player.
7. Press the SAT•CBL•DTC key to put the remote in that mode.
8. Press the POWER key to turn on the satellite receiver.
9. Press the MACRO key to save.
To execute the Macro, press the MACRO key. Press the 1 key. Your TV, DVD 

player, and satellite receiver should all power on.

1.   Press and hold the MACRO key until the POWER key turns on and remains on.
2.   Press the EXIT key. The POWER key blinks once, then remains on.
3.   Press the number key (1–8) where the macro you want to delete is stored. 

The POWER key blinks once, then remains on.

4.   Press the OK key to confirm the Macro Clear operation. The POWER key 

stays on for 2 seconds, then turns off. The selected Macro is deleted.

5.   Repeat steps 1-4 for any other existing Macros to be cleared.

6.   To learn another key for this device mode: Repeat steps 4 and 5 for the 

key you want to learn.

 

To learn keys in a different device mode: Repeat steps 2–5 for the next 

device mode.

 

To save learned keys and exit learning: press the SLEEP key on the 

learning remote.

Learning Tips
•  Make sure the batteries in both the learning and original remote(s) are fresh.
•  Incandescent or low-energy light can cause interference with IR 

4.   On the learning remote, press the key you want to use for the learned 

function. The illuminated POWER key blinks once, then remains on.

5.   On the original remote, press and hold the key you want to teach to the 

universal remote. Wait until the POWER key on the learning remote blinks 

once, then release the key on the original remote. The learning remote has 

finished learning this key.

Volume Punch-Through allows the VOL and MUTE keys, when pressed in 

SAT•CBL•DTC, DVD, DVR•AUX1 or VCR•AUX2 modes, to “punch through” to 

either TV or AUDIO, whichever was accessed last. Volume Punch-Through occurs 

automatically and allows you to control the volume without exiting the current 

mode. (If the DVR•AUX1 or VCR•AUX2 key has been programmed with a TV or 

AUDIO code, volume can punch through to these devices as well.)
Note: Volume Punch-Through does not occur in cases where the component 

1.   Press and hold the MACRO key until the POWER key 

turns on and remains on. The remote is now in Macro 

Programming mode.

2.   Press the number key (1–8) you want to use for this 

macro. The POWER key blinks once, then remains on.

3.   Press the device key for the first device you use in the macro. The POWER 

key blinks once and remains on.

4.   Press each key you want to use in this Macro, in the exact order the keys 

would be pressed if you were executing the sequence yourself. The POWER 

key blinks each time a key is pressed. Continue this process for all keys to be 

included in the Macro sequence under the given component mode.

5.   Once you are finished programming the Macro, press the MACRO key to save 

it. The POWER key illumination turns off, and the Macro is now ready to use.

 DVD 
 TV 
 SAT•CBL•DTC 
 AUDIO 
 DVR/VCR

 DVD 
 TV 
 SAT•CBL•DTC 
 AUDIO 
 DVR/VCR

Channel lock automatically sends channel commands, like the CH, GO BACK, 

and 0–9 number keys, to your satellite receiver, cable box, or digital TV converter 

when you’re in TV mode. This can save you keypresses if you use a device other 

than your TV to change channels. 
To turn channel lock on:
1. 

Press and hold the device key for the device you use to change channels. 

While you’re holding down this device key, use your other hand to press and 

hold the remote’s CH up key at the same time.

2.  Wait until the remote’s POWER key comes on and stays on. Then release 

both keys.

3.  Press ENTER to lock channel commands to this device.

To turn channel lock off:
1. 

Press and hold the TV key. While you’re holding down the TV key, use your 

other hand to press and hold the remote’s CH down key at the same time.

2.  Wait until the remote’s POWER key comes on and stays on. Then release 

both keys.

3.  Press ENTER to start changing channels with your TV.