Universal Remote Control UR4-EXP User Manual

The remote control is designed to operate
the Scientific-Atlanta Explorer series and
The Pioneer Voyager set top boxes. You can
also control the majority of TV, VCR/DVD and
AUDIO equipment on the market as shown
below.

CABLE : Cable Converters    
TV

: Televisions                VCR : VCRs and DVD      

AUX      : Audio Receivers,  DMX,  DCR,  TIVO, etc.

1

Default State: 
Device Default: CABLE
Channel Default: CABLE channel and number

keys through the CABLE, with the option of

controlling channel and number keys through

the TV or VCR. Refer to section F for

programming the channel and number keys

through your TV or VCR.
Volume Default: CABLE volume and mute

through the TV, with the option of controlling

volume and mute through the Cable box or Audio.

Refer to section G for programming the volume

and mute through your Cable box or Audio.

This button is designed to send out power

commands for two, three or all four devices

with one button press. Please refer to section E

for details.

4

2

Before you program or operate the remote control,
you must install two new AA alkaline batteries.

STEP1    Remove the battery compartment cover

on the back of your remote control.

STEP2    Check battery polarity carefully, and

install the batteries as shown In the
illustration below.

STEP3   Replace the battery compartment cover.

3

5

The remote control can be programmed by pressing in a three-digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit
code numbers are listed in the code table of the instruction manual.

STEP1    Turn on the equipment you wish to program. (TV,  VCR, DVD or AUX)

STEP2    Press the [DEVICE] button (TV, VCR or AUX) to be programmed and [SELECT] button

simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed. 

*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED

is on.

STEP3    Point the remote control toward the equipment and enter the three-digit code  number

assigned to your brand from the code tables.

*Tip : The equipment will turn off when the

correct three-digit code number has
been entered. You can verify you have
selected the correct code by pressing
the [POWER] button, the equipment
should turn on or turn off.

STEP4    Store the three-digit code number

by pressing the same [DEVICE]
button once again. The device LED
will blink twice to confirm that the
code has been stored.

If the three-digit code numbers assigned to
your brand do not turn off your equipment or
the code tables do not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
equipment by the following steps:

STEP1    Turn on the equipment you wish to

operate.

STEP2    Press the [DEVICE] button (TV, VCR

or AUX) to be programmed and
the [SELECT] button simultaneously
for 3 seconds. The device LED will
turn on.

*Tip : The device LED will turn on for 20

seconds. The next step must be
entered while LED is on.

STEP3     Press the [CH+] or [CH-] button one

step at a time or keep it pressed.
The remote will emit a series of
Power ON/OFF commands. Release
the [CH+] or [CH-] button as soon as
the equipment turns off.

*Tip : You can verify that you selected the

correct code by pressing the [POWER]
button. The equipment should either
turn on or off.

STEP4     Press the same [DEVICE] button to

store the code.  The device LED will
blink twice to confirm that the code
has been stored.

STEP1     Press the [DEVICE] button (TV, VCR

or AUX) you wish to verify and the
[SELECT] button simultaneously for 3
seconds. The device LED will turn on.

*Tip : The device LED will turn on for 20

seconds. The next step must be
entered while the LED is on.

STEP2     Press the [INFO] button.

The device LED will blink number of times
indicating the number of each digit of the
code number.  Each digit is separated by a 1
second interval of the LED being turned off.

STEP1    Press the [AUX] button to be

programmed and the [SELECT] button
simultaneously for 3 seconds.The
[AUX] device LED will turn on. 

*Tip : The device LED will turn on for 20

seconds. The next step must be
entered while the LED is on.

STEP2    Press the [TV] device button to pick

up the TV code table.

STEP3    Point the remote control toward the

equipment and enter the three-digit
code number assigned to your TV
brand from the code tables. 

STEP4    Store the three-digit code number by

pressing the [AUX] button once
again. The device LED will blink
twice to confirm that the code has
been stored.

This is designed to program the System On/Off
button so that it can send out up to four power
on/off commands with one button press.

STEP1    Press the [CBL] button.

STEP2    Press the [SYSTEM] button and the

[SELECT] button simultaneously for 3
seconds. The [CBL] button will turn
on for 20 seconds.

STEP3    Press the [DEVICE] button and the

[POWER] button you wish to store in
the System On/Off button and repeat
this until you stored all the power
commands into the System On/Off
button.

STEP4    Press the [CH+] button to save the

power commands you stored. The
[CBL] button will blink twice to
confirm the saving.

By following the steps below, the user can
program the channel controls (Channel Up,
Channel Down and Last) from one device to
operate in another device mode. The default
channel control settings on the remote
control is as follows:

CBL :  CBL 

T V :   CBL

VCR :  VCR 

AUX :  AUX

If you wish to store the TV channel control in
TV mode, use the following steps.

STEP1    Press the [TV] button and the

[SELECT] button simultaneously for
3 seconds. 

*Tip : The device LED will light on for 20

seconds. The next step must be
entered while the LED is on.

STEP2    Press the [VOL -] button.

STEP3    Press the  [TV] button. 

The device LED will blink twice to
confirm the programming. 

To return to original state:
If you wish to restore the CABLE channel
control in TV mode, repeat the above steps
by pressing [CBL] in    STEP3   .  

By following the steps below, the user can
program the volume controls (Volume Up,
Volume Down and Mute) from one device to
operate in another device mode. The default
volume control settings on the remote
control is as follows:

CBL :  TV 

T V :   TV

VCR :  TV 

AUX :  AUX

If you wish to store the CBL volume control in
CBL mode, use the following steps.
The [CBL] device LED will turn on.

STEP1 Press the [CBL] button and the

[SELECT] button simultaneously
for 3 seconds. 

*Tip : The device LED will turn on for 20

seconds. The next step must be
entered while the LED is on.

STEP2    Press the [VOL +] button.
STEP3    Press the  [CBL] button. 

The device LED will blink twice to
confirm the programming. 

To return to original state:
If you wish to restore the TV volume
control in CBL mode, repeat the above
steps by pressing [TV] in    STEP3   .  

In the CBL mode, the A, B and C buttons
can be programmed to act as a macro or
favorite channel button to send out up to 10
commands with one button press.

STEP1    Press the [CBL] button to select

the CBL mode.

STEP2    Press the [A, B, or C] button and

[SELECT] button simultaneously
for 3  seconds. The [CBL] device
LED will turn on for 20 seconds.

STEP3    Press up to 10 buttons you wish to

store. The [CBL] device LED will blink
once for each command entered.

STEP4    Press the [CH+] button to store the

functions that were selected. The
[CBL] device LED will blink twice to
confirm the storage of functions.

When the batteries are low and need to be
replaced with fresh batteries, the remote
control LED will blink 2 times in sequence
whenever a [POWER] button is pressed to
turn on equipment.

This remote control is designed to retain
programmed memory for 10 years even
after batteries are removed from the
remote control.

TV

Set-up Code Number:  

VCR

Set-up Code Number:

AUX

Set-up Code Number:

www.universalremote.com

OCE-0005A Rev 08 (02/06/07)