Universal Remote Control UR3-EXP User Manual
Universal Remote Control, Inc.
www.universalremote.com
OEE-0049A Rev 07(06/30/04)
UR3-EXP
Operating Instructions
For 3 Function
Cable Remote Control
The remote control is designed to operate the
Scientific-Atlanta Explorer 2000 and 3000
Series and the Pioneer Voyager set top boxes
and the majority of TV and VCR/DVD equipment
on the market.
Scientific-Atlanta Explorer 2000 and 3000
Series and the Pioneer Voyager set top boxes
and the majority of TV and VCR/DVD equipment
on the market.
Introduction
1
Default State :
Device Default : Scientific Atlanta Explorer
2000/3000 & Pioneer Voyager
Device Default : Scientific Atlanta Explorer
2000/3000 & Pioneer Voyager
Volume Default : TV volume and mute through
the TV, with the option of controlling volume and
mute through the Cable Converter. Refer to
Section F for programming the volume and mute
through your Cable Converter.
the TV, with the option of controlling volume and
mute through the Cable Converter. Refer to
Section F for programming the volume and mute
through your Cable Converter.
System On/Off button :
This button is designed to send out power
commands for two or all three devices with one
button press. Please refer to section E for details.
This button is designed to send out power
commands for two or all three devices with one
button press. Please refer to section E for details.
Operations
4
Replacing Batteries
2
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
illustration below.
STEP3 Replace the battery compartment cover.
Button Functions
3
Programming the Remote Control.
5
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three-digit code numbers are listed in the code table of the instruction manual.
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three-digit code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD)
STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button
simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed.
to be programmed.
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the
equipment and enter the three-digit
code number assigned to your
brand from the code tables.
code number assigned to your
brand from the code tables.
*Tip : The equipment will turn off when the
correct three-digit code number has
been entered. You can verify you have
selected the correct code by pressing
the [MUTE] button, the equipment
should turn on or turn off.
been entered. You can verify you have
selected the correct code by pressing
the [MUTE] button, the equipment
should turn on or turn off.
*Note : If there is more than one three-digit
number listed for your brand, try one
code number at a time until your
equipment turns off.
code number at a time until your
equipment turns off.
STEP4 Store the three-digit code number
by pressing the same [DEVICE]
button once again. The device LED
will blink twice to confirm that the
code has been stored.
button once again. The device LED
will blink twice to confirm that the
code has been stored.
*Note : Try all the functions on the remote
control. If any of the functions do not
work as they should, repeat from Step 2
using the next three-digit code number
from the same brand list. Make sure
that the VCR/VOD button is in the
VCR position when using your VCR.
work as they should, repeat from Step 2
using the next three-digit code number
from the same brand list. Make sure
that the VCR/VOD button is in the
VCR position when using your VCR.
B. Auto Search Method.
If the three-digit code numbers assigned to
your brand do not turn off your equipment or
the code tables do not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
equipment by the following steps:
your brand do not turn off your equipment or
the code tables do not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
equipment by the following steps:
STEP1 Turn on the equipment you wish to
operate.
STEP2 Press the [DEVICE] button (TV or
VCR) to be programmed and the
[SELECT] button simultaneously for 3
seconds. The device LED will turn on.
[SELECT] button simultaneously for 3
seconds. The device LED will turn on.
*Tip : The device LED will light on for 20
seconds. The next step must be
entered while LED is on.
entered while LED is on.
STEP3 Point the remote control toward the
equipment and alternately press the
[CH+] (or [CH-]) button and the
[MUTE] button. If the right code
number is sent, the equipment will
turn off.
[CH+] (or [CH-]) button and the
[MUTE] button. If the right code
number is sent, the equipment will
turn off.
*Tip : You can verify that you selected the
correct code by pressing the [MUTE]
button again. The equipment should
either turn on or turn off.
button again. The equipment should
either turn on or turn off.
STEP4 Press the same [DEVICE] button
to store the code. The Device
LED will blink twice to confirm
that the code has been stored.
LED will blink twice to confirm
that the code has been stored.
C. To Find the Three Digit Code
Number That was Stored in
the Device.
STEP1 Press the [DEVICE] button (TV or
VCR) you wish to verify and the
[SELECT ]button simultaneously for 3
seconds.
[SELECT ]button simultaneously for 3
seconds.
*Tip : The device LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
entered while the LED is on.
STEP2 Press the [INFO] button.
The device LED will blink number of times
indicating the number of each digit of the
code number. Each digit is separated by a 1
second interval of the LED being turned off.
Example : One blink, three blinks and eight
indicating the number of each digit of the
code number. Each digit is separated by a 1
second interval of the LED being turned off.
Example : One blink, three blinks and eight
blinks with an interval of 1 second
of LED being turned off, indicates
the code number 138.
of LED being turned off, indicates
the code number 138.
Note : Ten blinks is equal to the number 0.
D. Programming a second TV
to VCR Mode.
STEP1 Press the [VCR] button to be
programmed and the [SELECT]
button simultaneously for 3 seconds.
button simultaneously for 3 seconds.
*Tip : The device LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
entered while the LED is on.
STEP2 Press the [TV] device button to
pick up the TV code table.
STEP3 Point the remote control toward the
equipment and enter the three-digit
code number assigned to your TV
brand from the code tables.
code number assigned to your TV
brand from the code tables.
STEP4 Store the three-digit code number by
pressing the [VCR] button once again.
The device LED will blink twice to
confirm that the code has been stored.
The device LED will blink twice to
confirm that the code has been stored.
E. Programming the System On/Off Button.
This is designed to program the System on/off
button so that it can send out up to three
power on/off commands for the devices you
programmed into the remote control.
button so that it can send out up to three
power on/off commands for the devices you
programmed into the remote control.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM] button and the
[SELECT] button simultaneously for 3
seconds. The [CBL] button will turn
on for 20 seconds.
seconds. The [CBL] button will turn
on for 20 seconds.
STEP3 Press the [DEVICE] button you wish
to store in the System On/Off button
and repeat this until you stored all
the power commands into the
System On/Off button.
and repeat this until you stored all
the power commands into the
System On/Off button.
STEP4 Press the [CH+] button to save the
power commands you stored. The
[CBL] button will blink twice to
confirm the saving.
[CBL] button will blink twice to
confirm the saving.
F. Volume Punch Through:
By following the steps below, the user can
program the volume controls (Volume UP,
Volume Down and MUTE) from one device to
operate in another device mode.
The default volume control settings on the
remote control is TV volume control. If you
wish to store the CABLE volume control in
CBL mode, use the following steps.
program the volume controls (Volume UP,
Volume Down and MUTE) from one device to
operate in another device mode.
The default volume control settings on the
remote control is TV volume control. If you
wish to store the CABLE volume control in
CBL mode, use the following steps.
STEP1 Press the [CBL] button and the
[SELECT] button simultaneously for
3 seconds.
3 seconds.
*Tip : The device LED will light on for 20
seconds. The next step must be
entered while the LED is on.
entered while the LED is on.
STEP2 Press the [VOL +] button.
STEP3 Press the [CBL] button.
The device LED will blink twice to
confirm the programming.
confirm the programming.
To return to original state:
If you wish to restore the TV volume control in
CBL mode, repeat the above steps by
pressing [TV] in
If you wish to restore the TV volume control in
CBL mode, repeat the above steps by
pressing [TV] in
STEP 3 .
G. LOW BATTERY WARNING:
When the battery is low (2.0V-2.3V) and
needs to be replaced with fresh batteries,
the remote control LED will blink 2 times in
sequence whenever a [DEVICE] button is
pressed to turn on equipment.
needs to be replaced with fresh batteries,
the remote control LED will blink 2 times in
sequence whenever a [DEVICE] button is
pressed to turn on equipment.
H. Memory Lock System:
This remote control is designed to retain
programmed memory for 10 years even
after batteries are removed from the
remote control.
programmed memory for 10 years even
after batteries are removed from the
remote control.