One For All URC10820N User Manual
7
NOTE: If the LED did not blink twice, repeat steps 2 through 4
and enter the same code again.
and enter the same code again.
5. Aim the remote control at the device and press POWER once.
It should turn off. If the device does not respond, repeat steps
2 through 4, trying each code for your brand until you find
one that works. If it still does not work, try “Searching for Your
Code”.
2 through 4, trying each code for your brand until you find
one that works. If it still does not work, try “Searching for Your
Code”.
Searching For Your Code
If your device does not respond to the remote control after trying
all codes listed for your brand, or if your brand is not listed at all,
try searching for your code. For example, to search for a code for
your TV:
all codes listed for your brand, or if your brand is not listed at all,
try searching for your code. For example, to search for a code for
your TV:
1. Turn on your TV and on the remote control, press TV once.
2. Press and hold SET until the LED (red light) blinks twice, then
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
3. Enter 9 9 1. The LED will blink twice.
4. Select a test function from the list below or use the default test
4. Select a test function from the list below or use the default test
function (POWER) and skip step 4.
NOTE: The keys that can be used for the test function are 0, 1,
2, 3, POWER, VOL +, Play, Stop and MUTE.
5. Press CH+ to begin searching for your code. Stop the search
when the device turns off or performs the function selected in
step 4 (if other than POWER).
step 4 (if other than POWER).
NOTE: In the search mode, the remote control will send IR
codes from its library to the selected device, starting with the
most popular code first. Every press of CH+ will send a new
code. If you go past the code that performed the Test Function,
you can go back by pressing CH-.
codes from its library to the selected device, starting with the
most popular code first. Every press of CH+ will send a new
code. If you go past the code that performed the Test Function,
you can go back by pressing CH-.
6. To lock in the code, press and release the SET key. The LED
blinks twice.
7. To search for the codes of your other devices, repeat steps 1
through 6, but substitute the appropriate device key for the
device you are searching for in step 1.
device you are searching for in step 1.
Checking the Codes
If you have set up the remote control using the Searching For Your
Code procedure, you may need to find out which four-digit code is
operating your equipment. For example, to find out which code is
operating your TV:
Code procedure, you may need to find out which four-digit code is
operating your equipment. For example, to find out which code is
operating your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red light) blinks twice, then
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
3. Enter 9 9 0. The LED will blink twice.
4. To view the code for the first digit, press 1 once. Wait 3
4. To view the code for the first digit, press 1 once. Wait 3
seconds, count the LED blinks (e.g., three blinks = 3) and write
down the number in the leftmost box in the TV code boxes.
down the number in the leftmost box in the TV code boxes.
NOTE: If a code digit is 0, the LED will not blink.
5. Repeat step 4 three more times for remaining digits. Use 2 for
the second digit, 3 for the third digit, and 4 for the fourth digit.
Write down the code digits in the remaining TV code boxes.
Write down the code digits in the remaining TV code boxes.
6. To check for codes of other devices, repeat steps 1 through
5, but substitute the appropriate device key for each device
you are checking. Write down the device’s code digits in the
appropriate code boxes.
you are checking. Write down the device’s code digits in the
appropriate code boxes.