Panasonic AJ-HD130DCP User Manual
13
Operation
<Note>
During recording, check that the SERVO lamp is
lighted. If it is flashing or off, the images will be
subject to disturbances when they are played back.
During recording, check that the SERVO lamp is
lighted. If it is flashing or off, the images will be
subject to disturbances when they are played back.
Recording
Rec pause/recording (frame-to-
frame continuity)
frame continuity)
Press the PAUSE/STILL button while the
cassette tape is playing.
cassette tape is playing.
1
Press the REC button to set the VTR to the
REC PAUSE mode.
The monitor display is now switched to the E-E
screen.
When “REC-P” or “ALL” has been selected as the
setup menu item No.154 (AUTO BACK), the tape
is rewound for several seconds from the place
where the PAUSE/STILL button was pressed.
REC PAUSE mode.
The monitor display is now switched to the E-E
screen.
When “REC-P” or “ALL” has been selected as the
setup menu item No.154 (AUTO BACK), the tape
is rewound for several seconds from the place
where the PAUSE/STILL button was pressed.
2
Press the PAUSE/STILL button to start the
recording.
The tape runs up to the place where the
PAUSE/STILL button was pressed in step
recording.
The tape runs up to the place where the
PAUSE/STILL button was pressed in step
1
, and
recording is started.
<Note>
The E-E screen is now displayed.
<Note>
The E-E screen is now displayed.
3
Press the PAUSE/STILL button again to
temporarily stop the recording.
When “REC-P” or “ALL” has been selected as the
setup menu item No.154 (AUTO BACK), the tape
is rewound for several seconds from the place
where the PAUSE/STILL button was pressed,
and then it is temporarily stopped.
temporarily stop the recording.
When “REC-P” or “ALL” has been selected as the
setup menu item No.154 (AUTO BACK), the tape
is rewound for several seconds from the place
where the PAUSE/STILL button was pressed,
and then it is temporarily stopped.
4
Frame-to-frame continuity can be provided by
repeating steps
repeating steps
3
and
4
.
5
Set the cassette’s accidental erasure
prevention tab to the recording enable status,
and insert the tape.
prevention tab to the recording enable status,
and insert the tape.
1
1. Selecting the input audio signals
1) Connect the signals which are to be
recorded.
2) Select the audio input signals using setup
menu item No.700.
<Note>
For video signals, only HD SDI signals can
be input.
<Note>
For video signals, only HD SDI signals can
be input.
2. Adjusting the analog audio level
Adjust the level of the audio input signals when
analog audio signals have been selected as
the audio input signals.
The audio signals are recorded at the
appropriate level while the audio recording
level controls remain pushed in.
<Note>
The recording level cannot be adjusted when
HD SDI signals have been selected for the
audio input signals.
analog audio signals have been selected as
the audio input signals.
The audio signals are recorded at the
appropriate level while the audio recording
level controls remain pushed in.
<Note>
The recording level cannot be adjusted when
HD SDI signals have been selected for the
audio input signals.
3
Press the PLAY button while holding down
the REC button.
The REC and PLAY lamps light, and recording is
started.
When “ALL” has been selected as the setup
menu item No.154 (AUTO BACK) setting, the
tape is rewound for several seconds from the
place where the REC and PLAY buttons were
pressed and then, after a run-up, recording is
started from the place where the REC and PLAY
buttons were pressed. This ensures a smooth
continuity from one image frame to the next.
the REC button.
The REC and PLAY lamps light, and recording is
started.
When “ALL” has been selected as the setup
menu item No.154 (AUTO BACK) setting, the
tape is rewound for several seconds from the
place where the REC and PLAY buttons were
pressed and then, after a run-up, recording is
started from the place where the REC and PLAY
buttons were pressed. This ensures a smooth
continuity from one image frame to the next.
4
To end the recording, press the STOP button.
The recording ends, and the VTR is set to the
stop mode.
The recording ends, and the VTR is set to the
stop mode.
5
Press the STOP button to set the VTR to the
stop mode.
stop mode.
2