Sony 1500A User Manual
57
Digitally Dubbing Signals in DVCAM/DV Format
Ch
a
a
p
te
r 3
Co
nv
e
Co
nv
e
n
ien
t Fu
nc
tion
s
t Fu
nc
tion
s
f
o
r E
d
itin
g
Op
er
er
at
io
n
Digitally Dubbing Signals
in DVCAM/DV Format
in DVCAM/DV Format
In addition to straightforward tape dubbing, you can also
use this unit to dub signals in DVCAM/DV format
automatically from the beginning of the tape to the end
through the SDTI (QSDI) or i.LINK interface.
• To use the SDTI (QSDI) interface, the optional DSBK-
use this unit to dub signals in DVCAM/DV format
automatically from the beginning of the tape to the end
through the SDTI (QSDI) or i.LINK interface.
• To use the SDTI (QSDI) interface, the optional DSBK-
1501 board is required.
When a tape recorded on a DSR-1/1P Digital
Videocassette Recorder or DSR-130/130P Digital
Camcorder is dubbed, the ClipLink log data held in the
cassette memory is also copied.
Videocassette Recorder or DSR-130/130P Digital
Camcorder is dubbed, the ClipLink log data held in the
cassette memory is also copied.
Notes
• It is not possible to dub signals recorded in DV (LP)
format.
Digital dubbing is carried out in the digital format used
on the source tape regardless of the recording format
selected on this unit. If the source tape begins with a
section in which no signals are recorded, the
corresponding no-signal section created at the beginning
of the tape recorded on this unit may have a different
length depending on the digital format of the source tape,
the recording format selected on this unit, etc. During
dubbing, if the digital format of the source tape changes,
no signals are recorded until the initial digital format is
restored. No signals are recorded also when the digital
format used on the player is DV (LP).
Digital dubbing is carried out in the digital format used
on the source tape regardless of the recording format
selected on this unit. If the source tape begins with a
section in which no signals are recorded, the
corresponding no-signal section created at the beginning
of the tape recorded on this unit may have a different
length depending on the digital format of the source tape,
the recording format selected on this unit, etc. During
dubbing, if the digital format of the source tape changes,
no signals are recorded until the initial digital format is
restored. No signals are recorded also when the digital
format used on the player is DV (LP).
• Regardless of the audio recording mode setting of this
unit, dubbing is performed with the original audio
recording mode unchanged (two-channel/48 kHz mode
or four-channel/32 kHz mode).
recording mode unchanged (two-channel/48 kHz mode
or four-channel/32 kHz mode).
• Approximately the last 2 minutes of the tape may not be
copied because of differences in tape lengths. (If an
index picture is recorded in this portion, it may also not
be copied.)
index picture is recorded in this portion, it may also not
be copied.)
• A continuous recorded section of approximately 5
seconds is required before the recording start point. It is
recommended to record beforehand color bars or a
similar signal at the start point of the source tape to be
dubbed on this unit.
recommended to record beforehand color bars or a
similar signal at the start point of the source tape to be
dubbed on this unit.
Connections for dubbing via SDTI (QSDI)
interface
To carry out dubbing through the SDTI (QSDI) interface,
connect the REMOTE and SDTI (QSDI) IN/OUT
connectors on this unit to those on the DSR-85/85P/70A/
70AP/2000/2000P/1800/1800P/1600/1600P/1500A/
1500AP.
interface
To carry out dubbing through the SDTI (QSDI) interface,
connect the REMOTE and SDTI (QSDI) IN/OUT
connectors on this unit to those on the DSR-85/85P/70A/
70AP/2000/2000P/1800/1800P/1600/1600P/1500A/
1500AP.
For details of the connections and switch settings, see
“Connections for SDTI (QSDI) Dubbing” on page 96.
“Connections for SDTI (QSDI) Dubbing” on page 96.
Connections for dubbing via i.LINK interface
To carry out dubbing through the i.LINK interface,
connect the i.DV IN/OUT connectors on this unit and the
player.
Use the following procedure.
To carry out dubbing through the i.LINK interface,
connect the i.DV IN/OUT connectors on this unit and the
player.
Use the following procedure.
1
Press the MENU button in the menu control section.
2
Press the f or F button to select “AUTO
FUNCTION.”
FUNCTION.”
MENU
RESET(NO)
SET(YES)
TC
PRESET
2,4
1,9
2
3,4,5
7
Setup menu
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
HOURS METER
Monitor screen
Time counter display
Auto func
SYSTEM MENU
SETUP MENU
AUTO FUNCTION
HOURS METER
Monitor screen
Time counter display