JVC HR-S5950EU User Manual
Masterpage:Right-NoTitle0
EN
31
Filename [HRS5950EU3-EN.fm]
Page 31
December 4, 2001 5:14 pm
L-2 SELECT and L-2 INPUT Setting
The L-2 IN/DECODER connector accepts either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-2
SELECT” to the appropriate mode depending on the type of
appliance connected to the recorder’s L-2 IN/DECODER
connector. Set “L-2 INPUT” to the appropriate mode depending
on the output signals of the connected appliance.
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-2
SELECT” to the appropriate mode depending on the type of
appliance connected to the recorder’s L-2 IN/DECODER
connector. Set “L-2 INPUT” to the appropriate mode depending
on the output signals of the connected appliance.
A
Select the input mode for the L-2 IN/
DECODER connector.
DECODER connector.
B
Return to the normal screen.
Press MENU.
NOTES:
● If you have a satellite receiver or a decoder connected to the
L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back
to appropriate mode after editing.
to appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to
the L-2 IN/DECODER connector, leave “L-2 SELECT” set to “A/
V”.
V”.
● The default setting is “A/V”; if the recorder’s memory backup
has expired due to a power cut or because the AC was
removed from the recorder, “A/V” will be automatically
selected when the power is restored to the recorder. If you are
using a satellite receiver or a decoder, be sure to set “L-2
SELECT” back to appropriate mode.
removed from the recorder, “A/V” will be automatically
selected when the power is restored to the recorder. If you are
using a satellite receiver or a decoder, be sure to set “L-2
SELECT” back to appropriate mode.
● When “L-2 SELECT” is set to “SAT”, “SAT” or “SAt” appears on
TV screen or front display panel instead of “L-2” or “L2”.
● If “L-2 SELECT” is set to “DECODER”, it is impossible to set
“L-2 INPUT” to “S-VIDEO”.
● If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set
“L-2 SELECT” to “DECODER”.
Perform steps 1 and 2 of “L-1 OUTPUT Setting” on page 30.
Press rt to move the
highlight bar (pointer) to “L-2
SELECT” or “L-2 INPUT”.
Then, press OK or e to select
the appropriate setting.
highlight bar (pointer) to “L-2
SELECT” or “L-2 INPUT”.
Then, press OK or e to select
the appropriate setting.
* The default setting is bold in
the table below.
8
L-2 SELECT
A/V
:
To use this recorder as the recording
deck with the player connected to
the L-2 IN/DECODER connector, or
to use the satellite receiver
connected to the L-2 IN/DECODER
connector.
deck with the player connected to
the L-2 IN/DECODER connector, or
to use the satellite receiver
connected to the L-2 IN/DECODER
connector.
DECODER
:
To use a decoder connected to the
L-2 IN/DECODER connector.
L-2 IN/DECODER connector.
SAT
:
To view a satellite programme with
the TV set while the recorder is
turned off. (
the TV set while the recorder is
turned off. (
墌
pg. 32)
8
L-2 INPUT
VIDEO
:
If a connected appliance’s output is
compatible only with regular video
signals, set to “VIDEO”.
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO
:
If a connected appliance’s output is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain
high-quality S-VHS picture. (For
connection, be sure to use a 21-pin
SCART cable that is compatible with
the Y/C signal.)
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain
high-quality S-VHS picture. (For
connection, be sure to use a 21-pin
SCART cable that is compatible with
the Y/C signal.)
HRS5950EU1-EN.book Page 31 Tuesday, December 4, 2001 5:32 PM