JL Audio SB-GM-SLVEXT/10W6v2 Leaflet

Specifications:
Enclosure Type: Ported 
Driver Type: 10W6v2-D4
Nominal Impedance: 2

Ω

per woofer / can be rewired for 8

Ω

per woofer 

Cont. Power Handling: 400Watts per woofer / 800Watts for system

JL Audio recommends using a high quality amplifier such as the JL  Audio 500/1 or the JL Audio 1000/1. The diagram below shows
the recommended crossover, infrasonic filter and equalizer settings for either the 500/1 or the 1000/1 when being used to power
your Stealthbox®.

Included Hardware:
1) 3” x 3’ wax Square
1) 3/8”-16 x 2-1/4” Socket Cup Set Screw
1) 3/8” x 1-1/4” Fender Washer
1) 3/8” Flat Washer
1) 3/8” Split Lock Washer
1) 3/8” - 16 Hex Nut

10369 N. Commerce Pkwy, Miramar, Florida 33025-392      Phone: 954.443.1100     Fax: 954.443.1111

+12VDC

Remote

Ground

JL AUDIO 500/1

five-channel system amplifier

+

_

_

+

Subwoofer Output

MONO OUTPUT ONLY

40

45

55

65

85

120

200

Filter Freq. (Hz)

Mode / Slope

Off / 12dB / 24dB

Amp LP Filter

Infrasonic Freq. (Hz)

15

18

25

30

40

50

60

Off / 30Hz

Infrasonic Filter

0.5

0.7

1.1

1.6

2.7

4.3

"Q"

20

25

35

45

55

70

85

Center Freq.

0

+4

+10

+13

+15

Boost (dB)

Off / On

Bass EQ

Remote Bass Port

Advanced
Bass
Control

Preamp Output Section

Full Range / Amp Filter / Out Filter

Output Mode

Filter Slope

12dB / 24dB

40

45

55

65

85

120

200

Filter Freq. (Hz)

Left Ch.

Right Ch.

Filter Mode

LP / HP

Amplifier Input Section

Input Sens.

Left Ch.

Right Ch.

Signal Sensing

Off / On

Input Voltage

Low / High

The JL Audio 500/1 or the JL Audio 1000/1 is a very versatile audio component. Please consult the owner’s manual for
detailed information about installing and tuning this amplifier.

➔

➔

➔

STEP 6: Run speaker wire to the/each enclosure
and attach to the speaker terminal cup. Check the
woofer(s) for proper operation at this time.

STEP 7: Back out the/each socket cup set screw
to expose about 1-1/2”.

Place the socket cup set screw through the mount-
ing hole that was drilled, inside the truck.

From the under side of the truck, place a supplied
fender washer, flat washer, lock washer and then hex
nut onto the/each socket cup set screw.

Secure tightly, using a 14mm socket and ratchet.

STEP 8: Lower the rear seat and replace all
removed contents.

➔

S B - G M - S X T / 1 0 W 6 v 2 ,   J L   AU D I O,   I n c   2 0 0 6

S h e e t   S K U # 0 1 1 1 9 9     R ev i s i o n   1 / 1 2 / 2 0 0 6  

ZR650-CSi

TR400-CXi

Front Location Driver Size:
6.5” Separates

Applicable JL Audio Products:
TR,VR,XR & ZR650-CSi

Rear Location Driver Size:
4”x 6”

Applicable JL Audio Products:
TR400-CXi