Omega Vehicle Security HH806W User Manual
There are three display areas on the HH806 series LCD
(liquid crystal display). The Main and Second displays
are 4 _ digits with a maximum reading of 19999. These
are used for displaying the value of T1 or T2. The Third
display is for the date, time, or the differential value of
T1 to T2.
(liquid crystal display). The Main and Second displays
are 4 _ digits with a maximum reading of 19999. These
are used for displaying the value of T1 or T2. The Third
display is for the date, time, or the differential value of
T1 to T2.
Overload: “----.-” or “OL” is display.
Battery: 1.5V x 4 PCS (SIZE AAA) UM-4 R03.
Battery Life: 120 hours typical with carbon zinc battery.
Dimensions: 160mm(H) x 83mm(W) x 38mm(D).
Weight: Approx. 365g including batteries.
Supplied Thermocouple:
1 meter (40”) type K insulated beaded wire thermocou-
ple. Maximum insulation temperature is 482°C (900°F).
Thermocouple accuracy is ±1.1°C or 0.4% of reading
(whichever is greater) from 0°C to 1250°C.
1 meter (40”) type K insulated beaded wire thermocou-
ple. Maximum insulation temperature is 482°C (900°F).
Thermocouple accuracy is ±1.1°C or 0.4% of reading
(whichever is greater) from 0°C to 1250°C.
1. OPERATIONAL MODE
There are three operation modes-Normal, Shift, and
Setup Mode.
Setup Mode.
NORMAL MODE:
This is the default mode, the operating functions for
the normal mode are printed on top of each button in
white.
the normal mode are printed on top of each button in
white.
SHIFT MODE:
The operating functions for the shift mode are printed
in gray on the buttons. While in the normal mode,
press the SHIFT button to switch to shift mode. At the
lower-right corner of the display, the word “Shift” is
displayed to indicate shift mode. To switch back to
normal mode, press the SHIFT button again.
in gray on the buttons. While in the normal mode,
press the SHIFT button to switch to shift mode. At the
lower-right corner of the display, the word “Shift” is
displayed to indicate shift mode. To switch back to
normal mode, press the SHIFT button again.
SETUP MODE:
Press the set[ ] button in normal mode to switch to
setup mode, the indicator “SET” is shown on the left
side of the display. To switch back to normal mode,
press SET[ ] button again.
setup mode, the indicator “SET” is shown on the left
side of the display. To switch back to normal mode,
press SET[ ] button again.
WIRELESS MODE:
Press the “ ” key for more than two seconds to start
wireless function. Press “ ” for another two seconds
to stop wireless function. The wireless mode will shut
down if there is no wireless signal for two minutes.
SET CH/ID to 00,00 by pressing “T1-T2” key and
wireless function. Press “ ” for another two seconds
to stop wireless function. The wireless mode will shut
down if there is no wireless signal for two minutes.
SET CH/ID to 00,00 by pressing “T1-T2” key and
“
” power key for more than six seconds when the
meter with the meter powered down. The second dis-
play will show 00, which means that the channel and
ID has been set to 00.
play will show 00, which means that the channel and
ID has been set to 00.
To check the channel and ID of the meter:
When the meter is off press “
” key and “
” for
5 seconds. The LCD’s main display will show channel
number, the second display will show ID number.
number, the second display will show ID number.
2. NORMAL MODE
The following functions can only be used in the normal
mode.
(1) “ ” Power Button
The “
” button turns the thermometer on or off.
When the meter is in MAX/MIN record mode, the
power off function is disabled.
power off function is disabled.
(2) “[LIMITS]” Button (only Main display)
The limits function will alert the user when a meas-
urement exceeds a specified limit. To set the limit val-
ues, refer to limits function in the setup mode. Press
the [LIMITS] button to activate the limits function; the
word “LIMIT” should be displayed on the LCD.
When the value of the main display exceeds the Hi
limit, the word “Hi” will be displayed and the ther-
mometer will beep in a pulsed tone. If the value of the
main display is lower then the Lo limit, the word “Lo”
will be displayed and the thermometer will beep in a
continuous tone To exit the limits function, press the
[LIMITS] button.
urement exceeds a specified limit. To set the limit val-
ues, refer to limits function in the setup mode. Press
the [LIMITS] button to activate the limits function; the
word “LIMIT” should be displayed on the LCD.
When the value of the main display exceeds the Hi
limit, the word “Hi” will be displayed and the ther-
mometer will beep in a pulsed tone. If the value of the
main display is lower then the Lo limit, the word “Lo”
will be displayed and the thermometer will beep in a
continuous tone To exit the limits function, press the
[LIMITS] button.
(3) “ ” Button
The backlight function is represented by this button
“ ”. Pressing the button will turn on or off the LCD
backlight. The backlight will turn off automatically
after.
“ ”. Pressing the button will turn on or off the LCD
backlight. The backlight will turn off automatically
after.
(4) “SAVE/READ” Button
The read data function works in conjunction with the
save function in the shift mode, it is used for reading
saved data. The save function can be activated in shift
mode. Press the SAVE/READ button to read saved
data; the word “READ” should be displayed on the
LCD. To navigate around the save data table, press the
overlay “SECOND” button until the “#” sign is dis-
played on the second display. The location of the read
pointer within the saved data table will be displayed.
The arrow buttons on the overlay are used for scrolling
through the saved data. Press the smaller arrows “ ”
or “ ” to step through the data one at a time. Press the
larger arrows “
save function in the shift mode, it is used for reading
saved data. The save function can be activated in shift
mode. Press the SAVE/READ button to read saved
data; the word “READ” should be displayed on the
LCD. To navigate around the save data table, press the
overlay “SECOND” button until the “#” sign is dis-
played on the second display. The location of the read
pointer within the saved data table will be displayed.
The arrow buttons on the overlay are used for scrolling
through the saved data. Press the smaller arrows “ ”
or “ ” to step through the data one at a time. Press the
larger arrows “
” or “
” to step through the data
ten at a time. Pressing the overlay “ESC” button deac-
tivates the read data function.
tivates the read data function.
(5) “LOG/READ” Button
The read log function works in
with the
log function. It is used for reading logged data. The
log function can be activated in the shift mode. Press
the LOG/READ button to activate the log read func-
tion; the word “READ” is displayed on the LCD. Press
the overlay SECOND button to rotate through follow-
ing display menus: T1, T2, GRP, and #. T1 and T2:
Displays the T1 or T2 saved data. GRP: Displays the
current group number. #: Displays the current location
of the read pointer within a selected group. The arrow
buttons on the overlay are used for scrolling through
the data and groups. Press the smaller arrows “ ” or
“ ” to step through the logged data or groups one at a
time. Press the larger arrows “
log function can be activated in the shift mode. Press
the LOG/READ button to activate the log read func-
tion; the word “READ” is displayed on the LCD. Press
the overlay SECOND button to rotate through follow-
ing display menus: T1, T2, GRP, and #. T1 and T2:
Displays the T1 or T2 saved data. GRP: Displays the
current group number. #: Displays the current location
of the read pointer within a selected group. The arrow
buttons on the overlay are used for scrolling through
the data and groups. Press the smaller arrows “ ” or
“ ” to step through the logged data or groups one at a
time. Press the larger arrows “
” or “
” to step
through the data or groups ten at a time. To navigate
the logged data and groups, press the overlay
SECOND button until GRP appears in the second dis-
play panel. Then select the group using the arrows.
the logged data and groups, press the overlay
SECOND button until GRP appears in the second dis-
play panel. Then select the group using the arrows.
Press the SECOND button again until the “#” sign is
displayed. The location of the read pointer in the se-
lected group will be displayed. Use the arrows to
scroll through the data. Pressing the overlay “ESC”
button deactivates the read data function.
lected group will be displayed. Use the arrows to
scroll through the data. Pressing the overlay “ESC”
button deactivates the read data function.
(7) HOLD Mode (only Main display)
When HOLD mode is selected, the thermometer holds
the present readings and stops all further measure-
ments. To activate the data hold mode, press the
HOLD button, and “HOLD” is displayed on the LCD.
Pressing the HOLD button again cancels the function,
and the instrument will automatically resume meas-
urements.
the present readings and stops all further measure-
ments. To activate the data hold mode, press the
HOLD button, and “HOLD” is displayed on the LCD.
Pressing the HOLD button again cancels the function,
and the instrument will automatically resume meas-
urements.
(8) MIN/MAX with Time record Mode
(only Main display)
The MIN/MAX function records the highest and low-
est value recorded. It also calculates the average read-
ing and the differences of MAX to MIN. Press
MIN/MAX button to enter the MIN/MAX recording
mode. The beeper emits a tone when a new minimum
or maximum measurement is recorded. Press the
MIN/MAX button again to cycle through the current
readings: MAX: The highest measurement recorded.
MIN: The lowest measurement recorded. MAX-MIN:
The difference of the highest and the lowest measure-
ment. AVG: The average values of the measurements.
This mode works in conjunction with the hold func-
tion, pressing the HOLD button will stop recording
and measurements (Previously recorded readings are
not erased). Press HOLD button again to resume re-
cording and measurements. To prevent accidental loss
of MIN, MAX and AVG data, the MIN/MAX function
can only be cancelled by pressing and holding down
the MIN MAX key for more then 2 seconds. The
automatic power-off feature, and the power, °C/°F,
REL, SET, Hi/Lo Limits, TYPE, T1/T2 buttons are
also disabled.
est value recorded. It also calculates the average read-
ing and the differences of MAX to MIN. Press
MIN/MAX button to enter the MIN/MAX recording
mode. The beeper emits a tone when a new minimum
or maximum measurement is recorded. Press the
MIN/MAX button again to cycle through the current
readings: MAX: The highest measurement recorded.
MIN: The lowest measurement recorded. MAX-MIN:
The difference of the highest and the lowest measure-
ment. AVG: The average values of the measurements.
This mode works in conjunction with the hold func-
tion, pressing the HOLD button will stop recording
and measurements (Previously recorded readings are
not erased). Press HOLD button again to resume re-
cording and measurements. To prevent accidental loss
of MIN, MAX and AVG data, the MIN/MAX function
can only be cancelled by pressing and holding down
the MIN MAX key for more then 2 seconds. The
automatic power-off feature, and the power, °C/°F,
REL, SET, Hi/Lo Limits, TYPE, T1/T2 buttons are
also disabled.
(10) “T1/T2” Button (Main display)
The input selection button [T1/T2] selects the input for
the main display, T1 thermocouple or T2 thermocou-
ple. Press the T1/T2 button to switch between the two
inputs. When meter is turned on, it is set to the display
that was last in use.
the main display, T1 thermocouple or T2 thermocou-
ple. Press the T1/T2 button to switch between the two
inputs. When meter is turned on, it is set to the display
that was last in use.
(11) “T1/T2” Button (Second display)
The input selection button [T1/T2] selects the input for
the second display, T1 thermocouple or T2 thermo-
couple. Press the T1/T2 button to switch between the
two inputs. When meter is turned on, it is set to the
display that was last in use.
the second display, T1 thermocouple or T2 thermo-
couple. Press the T1/T2 button to switch between the
two inputs. When meter is turned on, it is set to the
display that was last in use.
(12) “T1-T2/TIME” Button (Third display)
The input selection button [T1-T2] selects the system
time and date, or the differential between the two
thermocouples (T1-T2) for the third display. Press the
T1-T2 button to switch the display options. When
meter is turned on, it is set to the display that was last
in use.
time and date, or the differential between the two
thermocouples (T1-T2) for the third display. Press the
T1-T2 button to switch the display options. When
meter is turned on, it is set to the display that was last
in use.
3. SHIFT MODE
The following functions can only be used in the
mode.
mode.
(2) “°C/°F” Button
Press the °C/°F button to select the temperature
readings can be displayed in Celsius (°C) or Fahre
heit (°F). When the thermometer is turned on, it
to the temperature scale that was last in use.
readings can be displayed in Celsius (°C) or Fahre
heit (°F). When the thermometer is turned on, it
to the temperature scale that was last in use.
(4) “SAVE” Button
The save function stores the T1, T2 data in a nonvola
tile memory. Press the SAVE button to save the
rent data, the word SAVE is displayed to indicate
data has been saved. The built in memory can store
to 128 data. The data can be read using the read
tion in the normal mode.
tile memory. Press the SAVE button to save the
rent data, the word SAVE is displayed to indicate
data has been saved. The built in memory can store
to 128 data. The data can be read using the read
tion in the normal mode.
(5) “LOG” Button
The data log function continuously records the
according to a specified time interval. The time
val can be set using the interval setup function [INVT]
in the set up mode. Press the LOG button to activate
the log function; the indicators “LOG” and “MEM”
will be displayed on the LCD. There are 16 groups
are used for storing the log data, and each group
64 data slots. If the current log session exceeds 64
points, the log function will automatically use the
group to store the following data. A maximum of
data points can be saved in one log session. Press
LOG button again to exit the data log function.
according to a specified time interval. The time
val can be set using the interval setup function [INVT]
in the set up mode. Press the LOG button to activate
the log function; the indicators “LOG” and “MEM”
will be displayed on the LCD. There are 16 groups
are used for storing the log data, and each group
64 data slots. If the current log session exceeds 64
points, the log function will automatically use the
group to store the following data. A maximum of
data points can be saved in one log session. Press
LOG button again to exit the data log function.
(6) “CLR ?” Button
The CLR function clears all the saved and logged
in memory. When the CLR button is pressed, indicator
“MEM” is displayed and the “CLR” on upper-right
LCD will blink. Pressing the “ENTER” button printed
on the overlay in white will clear all saved and logged
data. Press “ESC” button to exit this function without
clearing data.
in memory. When the CLR button is pressed, indicator
“MEM” is displayed and the “CLR” on upper-right
LCD will blink. Pressing the “ENTER” button printed
on the overlay in white will clear all saved and logged
data. Press “ESC” button to exit this function without
clearing data.
(7) “REL” Button (Main display)
The relative value function can be used for comparing
a saved reference value with other measurements.
Press the “REL” button to store the current measur
ment as the reference value, and “REL” should be
played on the right part of the LCD. The next
urement will display the current value compared
reference value. Press “REL” button again to clear
reference value and deactivate the relative value
urement function.
a saved reference value with other measurements.
Press the “REL” button to store the current measur
ment as the reference value, and “REL” should be
played on the right part of the LCD. The next
urement will display the current value compared
reference value. Press “REL” button again to clear
reference value and deactivate the relative value
urement function.
(8) “APO” Button
Press the APO button to turn the “Auto power
function on or off. When this function is enabled,
indicator “APO” is shown at the upper left part
LCD. When APO (Auto power off) is enabled, it
automatically turn the thermometer off no button
pressed for a period longer than the set time inte
(the default time for APO is 5 minutes). Press power
button to resume operation.
function on or off. When this function is enabled,
indicator “APO” is shown at the upper left part
LCD. When APO (Auto power off) is enabled, it
automatically turn the thermometer off no button
pressed for a period longer than the set time inte
(the default time for APO is 5 minutes). Press power
button to resume operation.
(10) “TYPE” Button (Main display)
Press this button to change the type of thermocouple
the main display (K/J/T/E/R/S/N). If the inputs
main and second display are the same, then pressing
the main display (K/J/T/E/R/S/N). If the inputs
main and second display are the same, then pressing
conjunction