Coleman 2000001598 User Manual

®   

STITCH LINE

1. Unfold tent and spread out on a clean, level surface with the 

door facing the desired direction. Unzip doors. (Fig. 1)

4. Assemble six, steel, shock-corded, Leg Poles. Push down

on steel button on tapered end and insert into end with
four holes.
NOTE: Make sure steel button locks 
into third hole on pole as shown. (Fig.4)

5. Insert curved end of Leg Poles

(with red marking) into
the ends of the Ridge 
Pole (with red marking). 
Insert curved end of 
remaining short Leg 
Poles into the ends of 
the remaining Ridge 
Poles. (Fig. 5 & 6)

6. Rotate all six Leg Poles upright and insert

pin on each web loop at the side locations 
as shown. (Fig. 7 & 7A)

(continued on other side)

Long Leg Pole, steel

(w/ red marking)

2

19mm

N/A

5010000614

Short Leg Pole, steel

4

19mm

N/A

5010000623

Curved Ridge Pole, steel 

(w/ red marking)

1

19mm

N/A

5010000613

Curved Ridge Pole, steel

2

19mm

N/A

5010000615

Side Window Pole, black,

fiberglass, metal tips

2

8.5mm

5010000541

5010000547

Door Pole, long, thin ,black,

fiberglass, rubber tips

1

6.3mm

5010000543

5010000545

Vert. Door Pole, short, black,

fiberglass, rubber tips

1

6.3mm

5010000543

5010000545

2. Pull four corners of tent taut, then secure by 

driving stakes through web loops at an angle 
for better anchoring. (Fig. 2)

3. Assemble three, steel, shock-corded, 

curved Ridge Poles. Insert Ridge Pole 
(with red marking) into center sleeve 
on top of tent with the red trim (Fig. 3). 
Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.

6. Assemble the two, shock-corded, black Window Poles, then 

insert one into sleeve located at each end of tent. (Fig. 7 & 7B)

7. Insert tapered metal tip on Window Pole into Leg Pole.

NOTE: It may be necessary to gently rotate Leg Pole so the 
hole will line up with the Window Pole.   

8. Go to opposite end of each window pole and gradually apply 

pressure to the pole forming an arch. Insert the pin into the 
leg pole end at the corners of tent. (Fig. 7 & 7C)

9. Locate the plastic hooks at sides and corners of tent, then 

snap onto Leg Poles to attach. (Fig. 8)

10. Locate web strap

with plastic hook on 
the sides of each 
end panel Window 
Vent, then snap onto 
the corner Leg Pole.
(Fig. 9)

12. Insert plastic stakes through web straps 

located on both sides of tent, then drive 
in to secure. (Fig. 11)

11. To stretch tent to finished size:

• Push in button on Leg Pole while 

twisting lower Leg Pole section
counterclockwise (Fig.10);

• Pull up on top Leg Pole section until 

tent is taut;

• Twist the lower Leg Pole clockwise 

until the button locks into the center 

or lowest hole;
• Repeat on remaining Leg Poles.

1. Assemble Vertical Door Pole (shorter 

black pole with plastic cap tips); then 
insert through zippered sleeve on side
of door and into hinge. (Fig. 12)

Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp 

objects, to install your tent.

•  Do not set up your tent under trees because of potential lightning strikes

or falling tree limbs in inclement weather.

• Secure with all stakes and guylines provided to prevent property damage

or personal injury.

•  For best results in windy conditions, position narrow end of tent into

the wind.

•  Enlist the help of at least one other person to assist you when it is time 

to assemble the tent.