Eureka! Tents N!ergy Portable Canopy User Manual

fig.1

fig.3

fig.2

fig.4

fig.5

fig.6

fig.9

fig.8

fig.10

fig.13

fig.14

fig.7

fig.12

fig.11

Component List: 1 Canopy Top,  1 Frame Assembly,  1 Carry Bag 

w/Wheels,  1 Pre-Installed Wiring Harness w/ Switch,  4 Nailhead 

Stakes,  4 Guy Out Skewers,  4 Attached Guy Out Cords

NOTE: Do not drop carry bag. Do not bounce the bag on its end to get 

Rev  B  4.09

Expand the Frame:

• Open the carry bag, remove the frame and top. Lay the top aside and 

stand the frame up, near its final location

• With one person at 

A and another at B, lift the poles and step back to 

pull the legs out and away from the center. See fig. 1. Move to 

C and D 

and again lift and pull the 

legs out and away. Work 

back and forth between 

AB and CD, until the 

frame is extended as 

shown in fig. 2

• If you are working alone, 

pull the frame apart as 

best you can and then 

drive a nailhead stake 

through the hole in the 

baseplate of one of the 

legs. See fig. 3. Work your 

way from corner, pulling 

out and away from the 

staked leg 

• Continue until the frame  

is extended as shown in  

fig. 2

Roof Rafters:

• At each corner, lift the 

bottom section of the 

perimeter rafter until the 

lock button on the leg 

clicks into its seat in the 

collar. See fig. 4 & 5. Take 

care that the collar truly 

captures the button, 

otherwise the roof will 

slide back down.

• Continue with the rest of 

the perimeter rafters 

until all corners are 

locked in place and the 

roof is extended as 

shown in fig. 6

Secure the Structure to the Ground:

• Drive a nailhead stake through the 

holes in the baseplates at the 

bottom of the legs. See fig. 12 

• Use the skewers to stake 

the guyout cords and 

adjust tension with the 

attached sliders. See fig. 13

• Lay the fabric on the ground with the top facing 

up and square to the frame. 

• Grasp the two canopy corners closest to the frame 

and drag them up and over the roof to the frame 

corners on the opposite side. Take care that the 

electrical plugs do not get caught on the frame as 

you tug the canopy 

• At each corner, fit the fabric snug to the frame. 

Align the guy gusset to the top of the frame and 

at a 45˚ angle from the leg. See fig. 7

• Move inside, under the canopy. Wrap each pair of 

Velcro® hook pads from the inside corners of the 

canopy to the loops near the top of the corner 

poles. See fig. 8

• Attach all remaining Velcro® tabs to the perimeter 

and roof rafters. See fig. 9

•  Station one person 

at each leg on one 

side of the frame. 

Lift the legs and 

press the button on 

the black collar to 

release the inside 

section. See fig. 10. 

Allow the inside 

sections to fall to one of the three lock 

points. Make sure that the legs are the 

same height and that they are locked in 

place. See fig.11

• Repeat with the remaining two legs

green

blue

E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold 

separately. Once connected to power, the control will display “green” at any switch 

that is “ON” and the “ON” socket will glow blue. See fig 14

Take Down: Pull up all stakes. Release the 

canopy’s hook & loop straps and remove 

from the frame. You may leave the wire 

harness in place. Collapse all poles and stow. 

Fold the canopy onto itself, roll up.and stow.

Read the important safety instructions on the 

reverse side.