Eureka! Tents Pine Lodge User Manual

Fan Door

poles

Main 

poles

Roof

poles

Wall

poles

1 Tent Body with Guy Ropes, 3 Main Poles, 6 Roof Poles, 6 Wall Poles, 4 Fan Door Poles, 

1 Carry Bag, 1 Stake Bag/Stakes, 1 Pole Bag

2. 

poles and divide according to 

size and shape. Take care; 

make sure that each pole 

section is fully seated into the 

next. Do not allow the 

sections to snap together as 

this can damage the ends. 

See fig 2.

1. 

Remove from the carry bag and separate all the components. Unroll and unfold the 

fabric top side up, on a clean, dry space and open the doors. If windy, stake down the 

windward corner. See fig 1. 

Guy Out: This tent has very large straight walls that act differently in high winds. If there 

are high winds, carefully follow the guy out instructions on the back side of this sheet.

Power Port: Open zipper and run extension cord 

through opening. Close zipper so that it rests 

next to the extension cord. Make sure the 

zipper cover is not twisted or tucked. The cover 

must lay flat against the outside of the tent to 

keep out rain. See fig 15.

Take Down: Remove the poles from the fan door. 

Pull up all stakes. Pull wall poles off of the pins 

and remove poles. Remove roof poles. Collapse 

all poles and stow. Fold the tent onto itself then 

roll up towards the open door and stow.

Options: Floor Saver and Fly/Awning.

fig 2

fig 1

fig 5

fig 6

fig 7

fig 8

fig 3

fig 13

fig 14

fig 15

fig 12

fig 14

fig 9

fig 10

3. 

Build the roof frame. Inset three black roof poles into the nylon elbows on one of 

the main poles at 

A, B and C. This forms the outer ridge. Move to the opposite side 

and again fit the same three poles into the nylon elbows of a second main pole at 

D, 

E and F. This forms one half of the roof. See fig 3 and 4.

3. 

Continue with the remaining three roof poles 

and main pole on the opposite side to 

complete the roof assembly. 

    See fig 5.

4. 

frame. Hook the shockcorded 

J-hooks to the brass rings 

and to the holes in the 

elbows.

Snap the web clips to the poles. It is best to start in the center and work your way out. You 

must do this now because you won’t be able to reach the clips and hooks once the walls 

are raised. See fig 6, 7 and 8.

NOTE: If you intend to install the optional fly/awning, do now. It is far easier to attach the 

fly/awning while the roof is still on the ground.

Step I:  Lay the Fly out on the ground in front of the tent, with the awning to the far front.

Step II:  With 2 people, grab the rear corners of the Fly & walk it over the top of the frame 

from front to back.

Step III:  There are 6 frame extensions, 1 each at the ends of the center ridge and eave 

poles front and rear.  See fig 9 positions A,B, D, E, F- position C not visible.  At the rear of 

the Fly, slide the 3 extensions in to the pockets sewn on the Fly (positions A, B, C).  

Repeat this step along the front of the tent at positions D, E & F. [Continue with tent 

set-up at number 5 'Raise the tent'.]

Step IV:  Once the tent is completely set up and staked out, insert the awning poles and 

stake them out.  See fig 11.

NOTE: When properly seated, the small 

spring on the pole will click into place.

5. 

Raise the tent. Start on one side and insert 

gray wall poles into the elbows. Locate the web 
ring/pins attached to the floor of the tent. Insert 
a pin into the base of each pole. See fig 9 & 10. 
Repeat on the other side until the tent is at full 
height and freestanding.

7.

 Assemble the fan door frame. Slide the 

fiberglass fan door poles, rubber end up, into 

the bottom of the door sleeves. Insert pins 

from the web loop into the bottom of these 

poles. See fig 12 & 13. Tuck the door into its 

perimeter envelope. 

There is a web loop on each side of the fan 

door, stake these down.

8

. Attach the splash guard. To provide an 

extra layer of protection, there is a flap that 

runs across the bottom near the inside of 

the door. Attach the J-hooks from this flap to 

loops at the front corners. See fig 14.

6.

 Stake the tent down. Stake 

out the corner rings first. As 

you work your way around the 

tent apply tension to square 

the tent and pull out any floor 

wrinkles. Align the center 

poles with the corners and 

stake out web side rings. See 

fig 12. [If you have the 

Fly/Awning option, now 

complete 'Step IV'.]

Important: Make sure the 

bottom front of the tent is in a 

straight line, from corner to 

corner. 

Rev.D  4.09

fig 11