JVC BR-D95U User Manual

146

41  1

CASSETTE EJECT

Cassette does not come

(AUTO OFF)

FAILURE

out in Eject.

56  1~

TAPE DEFECTIVE

Tape defect.

56  9

Tape loose

57  1~

END LEADER

Tape end sensor abnormal.

57  2

DETECTION

58  1~

BEGIN LEADER

Tape beginning sensor

58  2

DETECTION

abnormal.

70  1

DRUM MOTOR

Drum stops motion.

(AUTO OFF)

FAILURE

71  1

CAPSTAN MOTOR

Capstan stops its motion.

(AUTO OFF)

FAILURE

72  1~

SUP REEL MOTOR

Supply reel motor motion

72  8

FAILURE

abnormal.

(AUTO OFF)

73  1~

TU REEL MOTOR

Takeup reel motor motion

73  8

FAILURE

abnormal.

(AUTO OFF)

Behavior: Only warning indicator is active.
Action:

Consult your local JVC dealer.

When the MENU button is pressed, the
indication goes out.

Behavior: Stops, with no operation possible.
Action:

Turn the power off and then on.

Behavior: Cassette ejected.
Action:

If no abnormality is found in tape,
reload the cassette.

If there are any abnormalities when the self-diagnostics run after the power is turned on, the following warning indications are
shown. Self-diagnostics are executed when menu switch No. 357 <DIAG AT POWER ON> is set to “ON”. The warning code is
shown in 6 digits. “ x ” mark shows unspecified.

Behavior: Stops, with no operation possible.
Action:

Turn the power off and then on.

Behavior: Stops, with no operation possible.
Action:

Turn the power off and then on.

Behavior: Stops, with no operation possible.
Action:

Turn the power off and then on.

Behavior: Stops, with no operation possible.
Action:

Turn the power off and then on.

Behavior: Tape is fast-forwarded. If tape

begin is still detected 3 seconds
later, cassette is ejected.

Action:

Reload the cassette.

Behavior: Tape is rewound. If tape end is still

detected 3 seconds later, cassette
is ejected.

Action:

Reload the cassette.

80xxxx

CPU BUS FAILURE

Signal communication
between VCR’s micro-
processors abnormal.

820100

EEPROM FAILURE

EEPROM signal

820300

communication in VCR
abnormal.

840100

SYSCON REF FAILURE

System controller reference
signal failure.

850100

M/S REF

Mechanical controller

FAILURE

reference signal failure.

860100

TC REF FAILURE

Time code reference failure.

C0xxxx

MECHA(NO TAPE)

*1 Abnormal mechanical

FAILURE

operation.

On-screen display

DIAG WARNING 800400

CPU BUS FAILURE

(PUSH MENU KEY)

* Serial digital signals are used in conformity

with SMPTE259M for video and with AES/
EBU for audio.

*1

If the C02XXX indicator appears when the
power is turned ON it means that
condensation has occurred. Press the
[MENU] button until the indicator goes out.
Once the indicator has gone out, you can
operate the unit as usual.

147

Not operable

Not recordable

Playback impossible

On-screen display does
not come up

Noise appears on part of
the playback picture.

Tape counter does not run.

Menu setting cannot be
changed.

● Set [REMOTE] button to “LOCAL”.

● Set Menu switch No. 002 <OPERATION

LOCK> to “OFF”.

● Press [MENU] button to restore normal

mode.

● Set cassette’s protective slider to “REC”.

● Set menu switch No. 351 <PRE READ> to

“OFF”.

● S-VHS/VHS cassette not acceptable

● Connect monitor to [LINE2-SUPER OUT].

● Set [ON SCREEN] switch to ON.

● Clean the heads as instructed on page 11.

● Set menu switch No. 005 <AUTO TRACK-

ING> to “ON”.

   If noise appears when set to “ON”, set to

“OFF” and perform manual tracking
adjustment.

● Set menu switch No. 112 <ECC MODE> to

“NORMAL”.

● Press [MENU] button and enter Tape

Counter mode.

● Set menu switch No. 00D <MENU LOCK>

to “OFF”.

● The [REMOTE] button is set to “Remote”.

● Menu switch No. 002 <OPERATION

LOCK > set to“ ON”

● Menu setting mode entered

● Protective slider on the cassette not at

“REC”

● Menu switch No. 351 <PRE READ> is set

to “VID-ON” or “AUD-ON”.

● S-VHS/VHS cassette in use

● Monitor not connected to [LINE2-SUPER

OUT]

● [ON SCREEN] switch on the sub panel set

to OFF.

● The heads are dirty.

● Menu switch No. 005 <AUTO TRACKING>

set to “OFF”.

● Menu switch No. 112 <ECC MODE> set to

“NO CONCEAL” or “NO CORRECTION”

● CTL counter does not run on a non-

recorded section of the tape as no CTL
signal is recorded on such a section.

● Counter is in Menu Switch Setting mode.

● Menu switch No. 00D <MENU LOCK> is

set to “ON”.

Input signal cannot be
switched.

The Menu Switch
Setting mode cannot be
engaged.

During playback, the on-
screen sub time code
indication does not
advance.

● Set menu switch No. 371 <INPUT SE-

LECT SAFETY> to “OFF” or press the
signal switch while pressing the [SHIFT]
button.

● Install the SA-D95U.  Otherwise, digital

signals cannot be selected.

● Set menu switch No. 374 <MENU OPEN

SAFETY> to “OFF” or press the [MENU]
button while pressing the [SHIFT] button.

● Set menu switch No. 450 <SUB TC (VITC)

REC> to “ON” or menu switch No. 451
<VITC OUT SELECT> to “SUB TC”.

● Menu switch No. 371 <INPUT SELECT

SAFETY> is set to “ON”.

● The optional SA-D95U digital interface

board is not installed.

● Menu switch No. 374 <MENU OPEN

SAFETY> is set to “ON”.

● Menu switch No. 450 <SUB TC (VITC)

REC> is set to “OFF” and menu switch No.
451 <VITC OUT SELECT> is set to “OFF”
or “TC”.

● Sub time code is not recorded normally.