PHL Audio B17 User Manual

6.35 x 0.8 F

AST ON

 

Term

inal

4 x Ø 5.3 Holes on Ø 172

Ø 162.5 max.

Ø 117.5 max.

Ø 145.3 max.

68.5 max.

8

+

Red dot

Ø

 187.5 max.

(on angles)

Rated impedance 

Z

8

16

Ω

Reference efficiency (1 W@1 m)

-

94

94

dB SPL

Usable frequency range 

1

-

50–4000

50–4000

Hz

Power handling capacity 

2

(AES)

-

100

100

W

Max Sound Pressure Level 

3

SPLmax

110

110

dB SPL

Min. impedance modulus

Zmin

6.6 @ 370Hz

14.2 @ 330Hz

Ω

Voice-coil inductance 

4

@ 1 kHz

Le1k

0.72

1.36

mH

@ 10 kHz

Le10k

0.31

0.50

mH

Bl product

Bl

10.50

13.10

N/A

Moving mass

Mms

0.012

0.012

Kg

Resonance frequency 

5

Fs

53 (±8)

53 (±8)

Hz

DC resistance 

6

Re

6.1 (±0.6)

12.1 (±1.2)

Ω

Mechanical quality factor

Qms

3.6

3.6

1

Electrical quality factor

Qes

0.22

0.29

1

Total quality factor

Qts

0.21

0.26

1

Mechanical suspension compliance

Cms

750

750

10

-6

m/N

Effective piston area

Sd

0.0143

0.0143

m

2

Equivalent Cas air load

Vas

0.022

0.022

m

3

Max. linear excursion

Xmax

±3.5

±3.5

mm

Linear displacement volume

Vd

0.050

0.050

10

-3

m

3

Half-space efficiency

1.4

1.1

%

Unity load volume

Vas Qts

2

0.9

1.5

10

-3

m

3

Short term max. input voltage 

7

Vmax

60

85

V

Max. excursion before damage 

Xdam

8.0

8.0

mm

Ambient operating temperature 

–10    to   +50

°C

Storage temperature 

8

–20    to   +70

°C

Environmental conditions 

9

Outdoor

Air volume occupied by the driver 

10

0.5

0.5

10

-3 

m

3

Speaker net mass

2.15

2.15

Kg

Recommended reflex box 

Vb/Fb

12L / 65 Hz

L  /  Hz

Electrical polarity

A positive voltage applied on the red 

terminal produces forward cone motion.

Note 1 : Allowing for energy response, excursion capability,

Power spectrum, and -3dB low freq. roll-off for standard
reflex tuning.

Note 2 : Established at 20°C ambient temp, according to 

AES2-1984 standard using IEC268-1 simulated
programme signal and  a 12 liter Bass-Reflex test
enclosure tuned at 55Hz.

Note 3 : Established at 1m on axis of the loudspeaker mounted

in test enclosure, when driven at full AES Power
Handling Capacity, including 4dB of thermal
compression loss.

Note 4 : Measured at 20 mA in free air.

Note 5 : Measured at 20 mA and 20°C ambient temp. 

in free air conditions, after full  run and rest.

Note 6 : Measured at 20°C ambient temp. 

QC limits are ±10%

Note 7 : Stated in RMS voltage according to IEC 268-5.

Note 8 : Includes shipping conditions. The lower limit prevents

from demagnetization.

Note 9: Our products are classified in three categories : 

Indoor, Outdoor, and Outdoor

✚  

for permanent

outdoor use or severe conditions. 

Note 10 : Calculated for front mounting on to a 18 mm thick

board.

PHL Audio S.A. provides these specifications as representative of current production after conditioning. Because of our continuous research, they are subject to change without notice.

461, rue des chênes 

■

Z.A

7 7 5 9 0   C H A R T R E T T E S

FRANCE

T é l : 33 01 64 81 29 80

Fax : 33 01 60 69 10 28

e-mail : phlaudio@phlaudio.com

http: //www.phlaudio.com

■