Sony DSC-P73 User Manual
12
,
Connect the battery charger to
a wall outlet (wall socket) using
the power cord (mains lead).
a wall outlet (wall socket) using
the power cord (mains lead).
Charging starts, and the CHARGE lamp
lights. When the CHARGE lamp goes out,
charging is finished.
For details on the battery charger, see page
121.
lights. When the CHARGE lamp goes out,
charging is finished.
For details on the battery charger, see page
121.
To remove the batteries
Press the - end of the battery down in order
to raise the + end, then remove the battery.
to raise the + end, then remove the battery.
•
When charging is finished, disconnect the
power cord (mains lead) from the wall outlet
(wall socket), and remove the Nickel-Metal
Hydride batteries from the battery charger.
power cord (mains lead) from the wall outlet
(wall socket), and remove the Nickel-Metal
Hydride batteries from the battery charger.
Charging time
This represents the time required to charge fully
depleted Nickel-Metal Hydride batteries using
the supplied battery charger in an environment
where the ambient temperature is 25°C (77°F).
depleted Nickel-Metal Hydride batteries using
the supplied battery charger in an environment
where the ambient temperature is 25°C (77°F).
•
Charging is complete in approximately six
hours. The CHARGE lamp may remain lit
longer than six hours, but this is not a
malfunction.
hours. The CHARGE lamp may remain lit
longer than six hours, but this is not a
malfunction.
•
If you use the battery charger supplied with the
STAMINA “Quick charge” kit (not supplied),
the batteries will charge faster.
Charging time
When charging two Nickel-Metal Hydride
batteries: Approximately 2 hours 30 minutes
When charging four Nickel-Metal Hydride
batteries: Approximately 5 hours
STAMINA “Quick charge” kit (not supplied),
the batteries will charge faster.
Charging time
When charging two Nickel-Metal Hydride
batteries: Approximately 2 hours 30 minutes
When charging four Nickel-Metal Hydride
batteries: Approximately 5 hours
Notes on the Nickel-Metal
Hydride batteries
Hydride batteries
• At the time of purchase, or when the
Nickel-Metal Hydride batteries have not
been used for a long time, they may not
be fully charged. This is typical of this
type of battery, and is not a malfunction.
If this happens, repeatedly using up the
battery fully, and then recharging it,
should correct the problem.
been used for a long time, they may not
be fully charged. This is typical of this
type of battery, and is not a malfunction.
If this happens, repeatedly using up the
battery fully, and then recharging it,
should correct the problem.
•
If the poles of the Nickel-Metal Hydride
batteries are dirty, the batteries may not be
charged properly. Occasionally clean the poles
of the batteries and the terminals of the charger
by wiping them with a dry cloth.
batteries are dirty, the batteries may not be
charged properly. Occasionally clean the poles
of the batteries and the terminals of the charger
by wiping them with a dry cloth.
•
When transporting the Nickel-Metal Hydride
batteries, be sure to use the battery case
(supplied). If the +/- metal terminals are
shorted, there is a possibility of danger from
excessive heat or fire.
batteries, be sure to use the battery case
(supplied). If the +/- metal terminals are
shorted, there is a possibility of danger from
excessive heat or fire.
•
Even when Nickel-Metal Hydride batteries are
not being used they lose their charge naturally
over time. It is recommended that you recharge
the batteries just before using them.
not being used they lose their charge naturally
over time. It is recommended that you recharge
the batteries just before using them.
•
If you recharge Nickel-Metal Hydride batteries
before fully using up the existing charge, the
so-called memory effect* can occur, and the
low battery warning will be triggered sooner
than expected. Charging the battery after fully
depleting the existing charge should correct the
problem.
before fully using up the existing charge, the
so-called memory effect* can occur, and the
low battery warning will be triggered sooner
than expected. Charging the battery after fully
depleting the existing charge should correct the
problem.
*
The “memory effect” – the situation in which a
battery temporarily accepts a less than full
charge.
battery temporarily accepts a less than full
charge.
2
CHARGE
lamp
to a wall outlet
(wall socket)
(wall socket)
Power cord
(Mains lead)
(Mains lead)
Nickel-Metal Hydride
battery
battery
Charging time
NH-AA-DA
× 2
(supplied)
Approx. 6 hours