Panasonic DMC-LS60 User Guide
97
VQT1C63
Others
[MEMORY CARD ERROR FORMAT THIS
CARD?]
The format of the card cannot be
recognized by this camera. Format the
card again with this camera.
Save your data to your computer, then use
this unit to reformat the card. (P83)
CARD?]
The format of the card cannot be
recognized by this camera. Format the
card again with this camera.
Save your data to your computer, then use
this unit to reformat the card. (P83)
[PLEASE TURN CAMERA OFF AND
THEN ON AGAIN]
This message appears when the camera
is not operating properly. Turn the camera
off and on. If the message persists, contact
the dealer or your nearest Service Center.
THEN ON AGAIN]
This message appears when the camera
is not operating properly. Turn the camera
off and on. If the message persists, contact
the dealer or your nearest Service Center.
[MEMORY CARD ERROR
MEMORY CARD PARAMETER ERROR]
Use a card compatible with this camera.
(P5, 16)
You can only use 4 GB cards if they are
SDHC Memory Cards.
MEMORY CARD PARAMETER ERROR]
Use a card compatible with this camera.
(P5, 16)
You can only use 4 GB cards if they are
SDHC Memory Cards.
[MEMORY CARD ERROR
PLEASE CHECK THE CARD]
• Failed access to the card.
PLEASE CHECK THE CARD]
• Failed access to the card.
Insert the card again.
[READ ERROR
PLEASE CHECK THE CARD]
Data reading error.
Insert the card again. Make sure the card is
inserted properly and then play back again.
PLEASE CHECK THE CARD]
Data reading error.
Insert the card again. Make sure the card is
inserted properly and then play back again.
[WRITE ERROR
PLEASE CHECK THE CARD]
Data writing error.
Turn the camera off and remove the card.
Then insert the card and turn the camera
on again. This error may also indicate that
the card is damaged.
PLEASE CHECK THE CARD]
Data writing error.
Turn the camera off and remove the card.
Then insert the card and turn the camera
on again. This error may also indicate that
the card is damaged.
[MOTION RECORDING WAS CANCELLED
DUE TO THE LIMITATION OF THE
WRITING SPEED OF THE CARD]
• When you set the [PICT.MODE] to
DUE TO THE LIMITATION OF THE
WRITING SPEED OF THE CARD]
• When you set the [PICT.MODE] to
[30fpsVGA] or [30fps16:9], we recommend
using cards that offer 10 MB/second or
higher speeds (shown on their packages
and elsewhere) for best results.
using cards that offer 10 MB/second or
higher speeds (shown on their packages
and elsewhere) for best results.
• Depending on the type of Card, recording
may stop in the middle.
[A FOLDER CANNOT BE CREATED]
A folder cannot be created because there
are no remaining folder numbers that can
be used. (P85)
Save your data to your computer, then use
this unit to reformat the card. (P83)
If you execute [NO.RESET] in the [SETUP]
menu after formatting, the folder number is
reset to 100. (P22)
A folder cannot be created because there
are no remaining folder numbers that can
be used. (P85)
Save your data to your computer, then use
this unit to reformat the card. (P83)
If you execute [NO.RESET] in the [SETUP]
menu after formatting, the folder number is
reset to 100. (P22)
[PICTURE IS DISPLAYED FOR 4:3 TV]/
[PICTURE IS DISPLAYED FOR 16:9 TV]
• The video cable is connected to the
[PICTURE IS DISPLAYED FOR 16:9 TV]
• The video cable is connected to the
camera. Press [MENU/SET] if you want
to delete this message at once.
to delete this message at once.
• Select [TV ASPECT] in the [SETUP]
menu to change the TV aspect. (P23)
• This message also appears when the
USB connection cable is connected to
the camera only.
In this case, connect the other end of
the USB connection cable to a PC or a
printer. (P84, 87)
the camera only.
In this case, connect the other end of
the USB connection cable to a PC or a
printer. (P84, 87)
[PLEASE RE-CONNECT THE PRINTER.]
This message appears if you change the
mode dial to [
This message appears if you change the
mode dial to [
] while the camera and
the PC are connected. Set the camera to a
mode other than [
mode other than [
] mode, check that no
data is being transferred and then connect
to the printer again. ([ACCESS] appears
on the LCD monitor of the camera while
data is being transferred.)
to the printer again. ([ACCESS] appears
on the LCD monitor of the camera while
data is being transferred.)
[USB MODE CHANGED. PLEASE
REMOVE THE USB CABLE.]
This message appears if you change the
mode dial to a mode other than [
REMOVE THE USB CABLE.]
This message appears if you change the
mode dial to a mode other than [
] while
the camera and the printer are connected.
Set the mode dial to [
Set the mode dial to [
] again and then
disconnect the USB connection cable. If
this happens during printing, stop printing
and then disconnect the USB connection
cable.
this happens during printing, stop printing
and then disconnect the USB connection
cable.