Panasonic AJ-P2C064AG User Manual
Ad
justment
s
and S
ett
ings
fo
fo
r Recor
ding
49
Adjustments and Settings for Recording: Multi Format
Adjustments and Settings for Recording
For the unit to obtain image signals for each HD format, CCD is switching between interlaced scan and progressive scan
(reading all pixels).
With combinations of the SYSTEM MODE and CAMERA MODE menu options on the <SYSTEM MODE> screen on the
SYSTEM SETTING page, you can select an video system from among 13 types.
(reading all pixels).
With combinations of the SYSTEM MODE and CAMERA MODE menu options on the <SYSTEM MODE> screen on the
SYSTEM SETTING page, you can select an video system from among 13 types.
SYSTEM MODE menu option
Allows you to select a combination of system frequency
(59.94 Hz, 50 Hz, 23.98 Hz and 24 Hz) and signaling
system (1080i). When a change has been made to the
SYSTEM MODE option, the viewfinder indicates “TURN
POWER OFF”. Then, turn the POWER switch of the unit
off and wait 5 seconds or longer before turning the unit
on again.
(59.94 Hz, 50 Hz, 23.98 Hz and 24 Hz) and signaling
system (1080i). When a change has been made to the
SYSTEM MODE option, the viewfinder indicates “TURN
POWER OFF”. Then, turn the POWER switch of the unit
off and wait 5 seconds or longer before turning the unit
on again.
REC FORMAT menu option
Used to select the recording format.
AVC-I 100
The AVC-Intra100 format is used to record
video. The native recording format applies to
the 30PN, 24PN and 25PN modes.
video. The native recording format applies to
the 30PN, 24PN and 25PN modes.
AVC-I 50
The AVC-Intra50 format is used to record
video. The native recording is applied to the
30PN, 24PN and 25PN modes.
video. The native recording is applied to the
30PN, 24PN and 25PN modes.
DVCPROHD
The DVCPRO HD format is used to record
video.
video.
CAMERA MODE menu option
Selecting a shooting mode. For information about the
behavior for each setting, see [Recording formats and
output connector signal formats] (page 50).
behavior for each setting, see [Recording formats and
output connector signal formats] (page 50).
Notes
When the camera has been switched from 60i or 30P
to 24P or 24PA, video may produce noise for a
moment because the pull-down 5-frame cycle is
adjusted. This is not an abnormal condition.
When “AVC-I 50” or “AVC-I 100” is selected, the 24PA
mode cannot be selected.
to 24P or 24PA, video may produce noise for a
moment because the pull-down 5-frame cycle is
adjusted. This is not an abnormal condition.
When “AVC-I 50” or “AVC-I 100” is selected, the 24PA
mode cannot be selected.
VFR menu option
You can select whether to perform VFR recording.
ON
Enables variable frame rate shooting at the
frame rate set in FRAME RATE.
frame rate set in FRAME RATE.
OFF
The frame rate is determined according to the
REC FORMAT setting.
REC FORMAT setting.
24P VFR RANGE menu option
It is possible to increase the frame rate of VFR up to 30
frames when the SYSTEM MODE is set to “1080-
23.98PsF” or “1080-24PsF”.
frames when the SYSTEM MODE is set to “1080-
23.98PsF” or “1080-24PsF”.
24FRAME
1 to 24 frames can be set for VFR.
30FRAME
1 to 30 frames can be set for VFR. But the
output image becomes unnatural because the
HD SDI output signal sequence cannot be
maintained correctly.
output image becomes unnatural because the
HD SDI output signal sequence cannot be
maintained correctly.
FRAME RATE menu option
When the VFR menu option is set to “ON”, it is possible
to shoot using the frame rate set in this menu option.
When the VFR menu option is set to “ON”, pressing the
jog dial button displays the frame rate on the upper left
of the viewfinder screen as a blinking number. It is then
possible to change the frame rate setting without
opening the FRAME RATE menu option by pressing the
SYNCHRO SCAN adjustment buttons (+/-). Note,
however, that this operation is not available when the
FRATE function has been set to on using a user button.
to shoot using the frame rate set in this menu option.
When the VFR menu option is set to “ON”, pressing the
jog dial button displays the frame rate on the upper left
of the viewfinder screen as a blinking number. It is then
possible to change the frame rate setting without
opening the FRAME RATE menu option by pressing the
SYNCHRO SCAN adjustment buttons (+/-). Note,
however, that this operation is not available when the
FRATE function has been set to on using a user button.
Multi Format
Video system and Recording format
Selecting a recording signal and method
AJ-HPX3700G-VQT1V68_eng.book 49 ページ ２００８年１０月１５日 水曜日 午後６時３８分