Panasonic AG-HMC152EN User Manual
Shooting
33
Removing SD Memory Card
1
Tilt the viewfinder upwards, and open the
SD Memory Card slot cover by sliding it to
the left.
the left.
Ensure that the SD Memory Card access
lamp is not flashing orange before opening
the cover.
lamp is not flashing orange before opening
the cover.
2
Press the center of the SD Memory Card so
that it pops out slightly, and pull the card
straight outwards.
straight outwards.
SD Memory Card
access lamp
access lamp
2
1
Do not remove the SD Memory Card or switch off
the power in the following circumstances. Doing
so may damage your SD Memory Card.
the power in the following circumstances. Doing
so may damage your SD Memory Card.
1)
While the SD Memory Card access lamp is still
flashing orange after an SD Memory Card has
been inserted.
flashing orange after an SD Memory Card has
been inserted.
2)
While the SD Memory Card access lamp is
flashing such as during recording or during
recording finalization.
flashing such as during recording or during
recording finalization.
Protecting SD Memory Cards
Move the write-protect switch on the SD Memory
Card to the “LOCK” position to prevent recorded
contents being accidentally erased from the card.
Card to the “LOCK” position to prevent recorded
contents being accidentally erased from the card.
32
LOCK
Write-protect
switch
•
•
Repairing SD Memory Cards
Never remove the SD Memory Card or disconnect
the battery or DC cord while the SD Memory Card
access lamp is flashing, as doing so may damage
the SD Memory Card. In the event that the SD
Memory Card has been removed while the SD
Memory Card access lamp was flashing, or that
the battery or DC cord has been disconnected
during recording or the recording finalization
process, a repair verification screen will be
displayed the next time the power is switched on in
order to allow errors to be repaired.
the battery or DC cord while the SD Memory Card
access lamp is flashing, as doing so may damage
the SD Memory Card. In the event that the SD
Memory Card has been removed while the SD
Memory Card access lamp was flashing, or that
the battery or DC cord has been disconnected
during recording or the recording finalization
process, a repair verification screen will be
displayed the next time the power is switched on in
order to allow errors to be repaired.
Select YES to begin repairing. When repairing is
complete, “REPAIR FINISHED” will be displayed, and
the camera will switch to the recording paused screen.
Select NO to switch directly to the recording
paused screen without repairing.
complete, “REPAIR FINISHED” will be displayed, and
the camera will switch to the recording paused screen.
Select NO to switch directly to the recording
paused screen without repairing.
Memory cards cannot be repaired with the
camera if NO is selected, but can still be repaired
by using the AVCCAM Restorer∗ contents repair
software.
An SD Memory Card on which an error occurred
can be repaired by using either the camera
that was used for the shooting, or the AVCCAM
Restorer contents repair software.
A repair confirmation message may be displayed
after inserting an SD Memory Card which has no
error, but repair will not be performed even when
YES or NO is selected.
Repair may take up to 20 minutes or so
depending on the places where the errors
occurred on the card.
Use a battery with an adequate charge or the AC
adapter.
If the repair operation has failed, “SYSTEM
ERROR TURN POWER OFF” will be displayed.
In this case, please use the AVCCAM Restorer
contents repair software.
camera if NO is selected, but can still be repaired
by using the AVCCAM Restorer∗ contents repair
software.
An SD Memory Card on which an error occurred
can be repaired by using either the camera
that was used for the shooting, or the AVCCAM
Restorer contents repair software.
A repair confirmation message may be displayed
after inserting an SD Memory Card which has no
error, but repair will not be performed even when
YES or NO is selected.
Repair may take up to 20 minutes or so
depending on the places where the errors
occurred on the card.
Use a battery with an adequate charge or the AC
adapter.
If the repair operation has failed, “SYSTEM
ERROR TURN POWER OFF” will be displayed.
In this case, please use the AVCCAM Restorer
contents repair software.
Depending on the status of the data, it may not
be possible to restore all data completely. In this
case, it will no longer be possible to play back the
clips that were recorded before the power was
turned off.
Clips with a total recording time of less than 10
seconds may not be able to be repaired.
Indexes attached during recording cannot be
repaired.
case, it will no longer be possible to play back the
clips that were recorded before the power was
turned off.
Clips with a total recording time of less than 10
seconds may not be able to be repaired.
Indexes attached during recording cannot be
repaired.
∗ The AVCCAM Restorer can be downloaded from
the following website.
https://eww.pavc.panasonic.co.jp/pro-av/
https://eww.pavc.panasonic.co.jp/pro-av/
•
•
•
•
•
•
•
•