Panasonic AJ-P2C004HG User Manual
147
Connection with external device: Connection with external devices using the USB 2.0 port
Con
nec
tio
tio
n wi
th e
xte
th e
xte
rnal
de
vi
de
vi
ce
6
Select YES to start writing data to the cards.
<For your information>
To disable verification during writing, select HDD
SETUP from the thumbnail menu and set the option
VERIFY to OFF. This speeds up writing without verifying
data writing.
To disable verification during writing, select HDD
SETUP from the thumbnail menu and set the option
VERIFY to OFF. This speeds up writing without verifying
data writing.
7
When the writing is completed, the message “COPY
COMPLETED!” is displayed.
COMPLETED!” is displayed.
Note
If a clip is written back to a P2 card different from the original
card that contained that clip, then the clip may be
incomplete. If this is the case, reconnect the clip. For more
information, see [Reconnection of Incomplete Clips]
(page 129).
card that contained that clip, then the clip may be
incomplete. If this is the case, reconnect the clip. For more
information, see [Reconnection of Incomplete Clips]
(page 129).
A hard disk drive (including the P2 STORE (AJ-
PCS060G)) must be used under the following conditions:
– It must meet the operating requirements (e.g.
PCS060G)) must be used under the following conditions:
– It must meet the operating requirements (e.g.
temperature).
– It must not be placed in an instable place or a place
exposed to vibrations.
Some hard disk drives do not operate properly.
Some hard disk drives with the SATA (Serial ATA)
interface or the PATA (Parallel ATA) interface connected
by a USB conversion cable may not be recognized.
When copying data, a hard disk drive must have sufficient
free space.
Do not remove the cable or the target P2 card or turn off
the unit or hard disk drive during formatting or copying.
Doing so requires the unit and the hard disk drive to be
restarted.
Since hard disk drives are high precision devices, there is
a high possibility that they may become incapable of
reading/writing data depending on the conditions of use.
Take note that we will not be liable for loss of data
caused by failed hard disk drives or any other
problem as well as direct or indirect damages
resulting from the loss of data.
We do not guarantee that hard disk drives will operate
properly with the unit or that the data on them will be
properly retained if data copied to them from the unit has
been replaced with other data using a PC.
By using the drive mount converter distributed on the
following URL, the hard disk drive can be mounted in the
designated folder when connected.
When the drive letter used to denote the hard disc drive is
the same as one already assigned to a network drive, the
partition may not be displayed. When this problem occurs,
use the drive mount converter to mount the hard disk drive
in a designated folder. The partition will then be displayed.
Some hard disk drives with the SATA (Serial ATA)
interface or the PATA (Parallel ATA) interface connected
by a USB conversion cable may not be recognized.
When copying data, a hard disk drive must have sufficient
free space.
Do not remove the cable or the target P2 card or turn off
the unit or hard disk drive during formatting or copying.
Doing so requires the unit and the hard disk drive to be
restarted.
Since hard disk drives are high precision devices, there is
a high possibility that they may become incapable of
reading/writing data depending on the conditions of use.
Take note that we will not be liable for loss of data
caused by failed hard disk drives or any other
problem as well as direct or indirect damages
resulting from the loss of data.
We do not guarantee that hard disk drives will operate
properly with the unit or that the data on them will be
properly retained if data copied to them from the unit has
been replaced with other data using a PC.
By using the drive mount converter distributed on the
following URL, the hard disk drive can be mounted in the
designated folder when connected.
When the drive letter used to denote the hard disc drive is
the same as one already assigned to a network drive, the
partition may not be displayed. When this problem occurs,
use the drive mount converter to mount the hard disk drive
in a designated folder. The partition will then be displayed.
https://eww.pavc.panasonic.co.jp/pro-av/
Direction for using a hard disk drive
AJ-HPX2700G-VQT1V27_eng.book 147 ページ ２００８年９月２日 火曜日 午後５時４３分