Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. AJ-P2C004HG
  5. User Manual

Panasonic AJ-P2C004HG User Manual

Download
Page of 206
156
Maintenance and Inspections: Warning System
6. Recording Error
Display window 
indication
“00:00:00:11” appears in the time code 
display field. Even after recording is 
stopped, this display continues to blink 
until the next operation is performed.
WARNING lamp
Blinks 4 times per second while recording 
continues.
Tally lamp
Blinks 4 times per second while recording 
continues.
Viewfinder
The “REC WARNING” indicator lights up.
Warning tone
Beeps 4 times per second while recording 
continues.
Warning description
This indicates a failure either in the P2 
card recording or the recording circuit. 
This is displayed when attempting to 
record clips where the total quantity 
exceeds the upper limit (1000 pieces) for 
a single P2 card.
Recording/playback 
operation
The recording may stop or continue.
Countermeasures
Confirm the recording/playback operation 
after turning off the power supply once 
and then turning it on again.
If the recording cannot be performed 
normally, change the P2 card.
7. Low Wireless Signal Reception
Display window 
indication
No display.
WARNING lamp
Blinks 4 times per second (during pause 
and recording).
Tally lamp
Blinks 4 times per second while recording 
continues.
Viewfinder
The “WIRELESS-RF” indicator lights up 
while recording continues.
Warning tone
Beeps 4 times per second while recording 
continues.
Warning description
This error indicates poor wireless audio 
reception conditions.
Recording/playback 
operation
Continues to operate without receiving 
the wireless microphone signal.
Countermeasures
Check the microphone power supply and 
the reception status of the wireless 
receiver.
8. 1394 Error
Display window 
indication
The “1394 E-92” indicator in the display 
window blinks.
WARNING lamp
Blinks 4 times per second while recording 
continues.
Tally lamp
Blinks 4 times per second while recording 
continues.
Viewfinder
“1394 INITIAL ERROR” indicator lights up 
(during pause and recording).
Warning tone
Beeps 4 times per second while recording 
continues.
Warning description
This indicates a failure of the DVCPRO 
connector.
Recording/playback 
operation
Signals cannot be controlled or supplied 
to the device connected to the DVCPRO 
connector. However, recording and 
playback can be performed on the unit.
Countermeasures
Check the connection between the 
IEEE1394 cable and the DVCPRO 
connector, settings of any external device 
and menus, and the turn on the power 
again.
If the warning indication is still 
illuminated, consult your distributor.
9. Battery Nearly Empty
Display window 
indication
One of the bars in the battery remaining 
indicator starts blinking.
WARNING lamp
Blinks once per second.
Tally lamp
Blinks once per second.
Viewfinder
The “BATT” LED blinks.
Warning tone
Beeps 4 times per second.
Warning description
The battery is about to run out.
Recording/playback 
operation
Continues to operate.
Countermeasures
Replace the battery as required.
10. P2 Card Nearly Full
Display window 
indication
One of the bars for remaining MEDIA 
capacity starts blinking.
WARNING lamp
Blinks once per second while recording 
continues.
Tally lamp
Blinks once per second while recording 
continues.
Viewfinder
The P2 card remaining capacity indicator 
blinks.
Warning tone
Beeps once per second while recording 
continues.
Warning description
The total remaining capacity of all the P2 
cards is 2 minutes or less.
Recording/playback 
operation
Continues to operate.
Countermeasures
Replace the cards. If there is an empty 
card slot, insert a new card.
AJ-HPX2700G-VQT1V27_eng.book  156 ページ  ２００８年９月２日　火曜日　午後５時４３分