Panasonic AJ-P2C004HG User Manual
50
Adjustments and Settings for Recording: Adjusting the White balance and Black Balance
The detection area for the white balance is selectable
between “90%”, “50%” and “25%”, using the menu option
AWB AREA.
This option can be found in the <WHITE BALANCE MODE>
screen on the CAM OPERATION page.
The detection area is factory-set to “25%”.
between “90%”, “50%” and “25%”, using the menu option
AWB AREA.
This option can be found in the <WHITE BALANCE MODE>
screen on the CAM OPERATION page.
The detection area is factory-set to “25%”.
Position the WHITE BAL switch at [PRST].
This adjusts the white balance for the filter according to the
position of the CC/ND FILTER control.
This adjusts the white balance for the filter according to the
position of the CC/ND FILTER control.
When the white balance has not been successfully adjusted,
the viewfinder displays an error message.
If one of the error messages listed below appears, take the
appropriate steps, then adjust the white balance again.
If the error message appears after repeated readjustments,
the interior of the unit must be inspected. For more
information, contact your distributor.
the viewfinder displays an error message.
If one of the error messages listed below appears, take the
appropriate steps, then adjust the white balance again.
If the error message appears after repeated readjustments,
the interior of the unit must be inspected. For more
information, contact your distributor.
Each value in memory is retained even if the unit is turned
off; it will not be lost until the white balance is re-adjusted.
White balances are stored in either of two systems: A or B.
When the menu option FILTER INH is set to “ON” (default),
each system stores only one value. If this is the case, the
values are not synchronized with the filters.
This option can be found in the <WHITE BALANCE MODE>
screen on the CAM OPERATION page.
When the menu option FILTER INH is set to “OFF”, the
adjusted value for each filter can be automatically stored in
the memory that corresponds to the position of the WHITE
BAL switch ([A] or [B]). Your unit has 4 built-in filters; it stores
8 (4 2) adjusted values.
off; it will not be lost until the white balance is re-adjusted.
White balances are stored in either of two systems: A or B.
When the menu option FILTER INH is set to “ON” (default),
each system stores only one value. If this is the case, the
values are not synchronized with the filters.
This option can be found in the <WHITE BALANCE MODE>
screen on the CAM OPERATION page.
When the menu option FILTER INH is set to “OFF”, the
adjusted value for each filter can be automatically stored in
the memory that corresponds to the position of the WHITE
BAL switch ([A] or [B]). Your unit has 4 built-in filters; it stores
8 (4 2) adjusted values.
Detection area for the white balance
When you have no time to adjust the white
balance
balance
When the white balance has not been
automatically adjusted
automatically adjusted
Error message
Description
Remedies
COLOR TEMP
HIGH
HIGH
The color
temperature is too
high.
temperature is too
high.
Select an appropriate
filter.
filter.
COLOR TEMP
LOW
LOW
The color
temperature is too
low.
temperature is too
low.
Select an appropriate
filter.
filter.
LOW LIGHT
There is insufficient
light.
light.
Increase the light
level or gain.
level or gain.
LEVEL OVER
There is too much
light.
light.
Decrease the light
level or gain.
level or gain.
CHECK FILTER
The FILTER control is
displaced.
displaced.
Check the FILTER
control.
control.
TIME OVER
AWB was not
completed within the
time allowed.
completed within the
time allowed.
Shooting conditions
may be unstable. If
flicker occurs, press
the shutter and
readjust the AWB
under stable
conditions.
may be unstable. If
flicker occurs, press
the shutter and
readjust the AWB
under stable
conditions.
90%
50%
25%
Retaining white balances
AJ-HPX2700G-VQT1V27_eng.book 50 ページ ２００８年９月２日 火曜日 午後５時４３分