Panasonic AG-HVX200AP User Manual
86
P2
To check the data copied into the hard disk drive
After step
After step
4 on the previous page, use the and
buttons to select PROPERTY, and then press
the button.
The contents of the hard disk drive are displayed.
• To view details of the items, select an item using
The contents of the hard disk drive are displayed.
• To view details of the items, select an item using
the and buttons, and press the button.
To verify the data when copying it into the hard
disk drive
After step 4 on the previous page, use the and
disk drive
After step 4 on the previous page, use the and
button to select YES from the VERIFY option on
SETUP.
• Copying to the P2 card is completed, even if you
• Copying to the P2 card is completed, even if you
interrupt processing during verification.
• You cannot copy data from the hard disk drive to
a P2 card.
• Use a hard disk drive under the following
conditions.
1)
Power is supplied from a source other than the
1394 bus. (It is not supplied from the unit.)
1394 bus. (It is not supplied from the unit.)
2)
You may format the hard disk drive for usage
by the unit.
by the unit.
3)
Use the hard disk drive within the guaranteed
operating range (humidity and other
environmental conditions).
operating range (humidity and other
environmental conditions).
4)
Do not place the hard disk drive in an unstable
locations or locations subjected to vibrations.
locations or locations subjected to vibrations.
• Some HDD may not operate correctly.
• During formatting or copying, do not remove any
• During formatting or copying, do not remove any
cables, eject the P2 card, or turn off the power for
the unit or hard disk drive. The power will need to
be turned on again.
the unit or hard disk drive. The power will need to
be turned on again.
• No guarantees are made for operation if the
1394 HOST mode is established without first
connecting the HDD (1394.a SBP2 supported)
and then the HDD is connected. In this case, turn
off the power, and then release the 1394 HOST
mode.
connecting the HDD (1394.a SBP2 supported)
and then the HDD is connected. In this case, turn
off the power, and then release the 1394 HOST
mode.
• The hard disk drive is an extremely high-
precision device. Therefore, it is highly
possible that data cannot be read in certain
operating environments.
possible that data cannot be read in certain
operating environments.
Please note that our company will not be
liable for any data losses due to hard disk
drive failure or other faults, or any other direct
or indirect damage related to these problems.
drive failure or other faults, or any other direct
or indirect damage related to these problems.
• If you rewrite the contents of the HDD used
to carry out copying from the camera to
another PC, the subsequent operation in the
camera and the data in the HDD cannot be
guaranteed.
another PC, the subsequent operation in the
camera and the data in the HDD cannot be
guaranteed.
• It is recommended that you first restore any
defective clips contained in the P2 card before
copying the data.
copying the data.
• In order to avoid the occurrence of trouble in
copying, formatting or other operations, it is
recommended that you perform these operations
after ensuring that power supply has stabilized.
recommended that you perform these operations
after ensuring that power supply has stabilized.
Warnings
HDD CAPACITY FULL!
There is not enough free memory on the HDD.
TOO MANY PARTITIONS!
There are too many partitions.
HDD DISCONNECTED!
The HDD has been disconnected.
CANNOT INITIALIZE!
Initializing cannot be performed.
TOO MANY TARGETS!
There are too many 1394 connection
There is not enough free memory on the HDD.
TOO MANY PARTITIONS!
There are too many partitions.
HDD DISCONNECTED!
The HDD has been disconnected.
CANNOT INITIALIZE!
Initializing cannot be performed.
TOO MANY TARGETS!
There are too many 1394 connection
destinations.
CANNOT ACCESS TARGET!
The connection destination cannot be accessed.
CANNOT ACCESS CARD!
The card cannot be accessed.
MISMATCH COMPONENT!
There is a mismatch with the connection
The connection destination cannot be accessed.
CANNOT ACCESS CARD!
The card cannot be accessed.
MISMATCH COMPONENT!
There is a mismatch with the connection
destination.
UNKNOWN DEVICE CONNECTED!
A device other than an HDD has been connected.
P2 CARD IS UNFORMATTED!
The P2 card is still unformatted.
CARD IS EMPTY! CANNOT COPY!
There is no data on the P2 card and so it cannot
A device other than an HDD has been connected.
P2 CARD IS UNFORMATTED!
The P2 card is still unformatted.
CARD IS EMPTY! CANNOT COPY!
There is no data on the P2 card and so it cannot
be copied.
VERIFICATION FAILED!
A mismatch was discovered by verification.
TURN POWER OFF!
Turn off the power.
CANNOT RECOGNIZE HDD!
HDD recognition failed.
A mismatch was discovered by verification.
TURN POWER OFF!
Turn off the power.
CANNOT RECOGNIZE HDD!
HDD recognition failed.
Copying from P2 cards to the hard disk drive (1394 HOST mode) (continued)