Sony BRU-H700 User Manual
Location and Function of Parts
5
GB
Location and Function
of Parts
of Parts
Front
A Power switch
Turns on/off the power of this unit.Turn on the
power of the BRC-H700 camera before you turn on
this unit.
power of the BRC-H700 camera before you turn on
this unit.
B Power indicator
Lit in green: This unit is in normal operation.
Lit in red: The power of the camera connected to
this unit is turned off. Turn it on.
Flashing in red: Abnormal operation of this unit.
Display the composite video signal on the monitor
and check the error message. Check also the
connection.
Lit in red: The power of the camera connected to
this unit is turned off. Turn it on.
Flashing in red: Abnormal operation of this unit.
Display the composite video signal on the monitor
and check the error message. Check also the
connection.
C DATA MIX switch
Set the switch to ON to overlap the menu with the
video signal output from the installed interface
board. Set it to OFF not to overlap the menu.
video signal output from the installed interface
board. Set it to OFF not to overlap the menu.
Rear
D Card slot
Insert an optional interface board, HFBK-SD1,
HFBK-HD1, HFBK-XG1 or HFBK-TS1.
The slot cover is attached to the unit at the factory.
HFBK-HD1, HFBK-XG1 or HFBK-TS1.
The slot cover is attached to the unit at the factory.
E AUDIO OUT L/R jacks
Loop through output of the audio line signal input
from the AUDIO IN jacks on the BRBK-H700 HD
from the AUDIO IN jacks on the BRBK-H700 HD
Optical Multiplex Card inserted into the camera via
the Optical Fiber Cable.
the Optical Fiber Cable.
F ~AC IN connector
Connect the supplied AC power cord.
G CAMERA connector
Connect to the optical connector of the BRBK-
H700 HD Optical Multiplex Card installed in the
BRC-H700 camera using the CCFC-M100HG
Optical Fiber Cable.
A dustproof cap is attached at the factory.
H700 HD Optical Multiplex Card installed in the
BRC-H700 camera using the CCFC-M100HG
Optical Fiber Cable.
A dustproof cap is attached at the factory.
H EXT SYNC IN connector
Accepts external video sync signals.
I EXT SYNC OUT connector
Supplies external video sync signals input from the
EXT SYNC IN connector.
EXT SYNC IN connector.
J
RGB/COMPONENT connector
Supplies the images from the camera as YPbPr or
RGB signal.
RGB signal.
K VISCA RS-232C IN connector
Connect to the RM-BR300 Remote Control Unit
(not supplied). When you connect multiple
cameras, connect it to the VISCA RS-232C OUT
connector of the previous camera in the daisy chain
connection.
(not supplied). When you connect multiple
cameras, connect it to the VISCA RS-232C OUT
connector of the previous camera in the daisy chain
connection.
L VISCA RS-232C OUT connector
When you connect multiple cameras, connect it to
the VISCA RS-232C IN connector of the next
camera in the daisy chain connection.
the VISCA RS-232C IN connector of the next
camera in the daisy chain connection.
M VISCA RS-422 connector
Connect to the VISCA RS-422 connector of the
camera or another BRU-H700 HD Optical
Multiplex Unit.
camera or another BRU-H700 HD Optical
Multiplex Unit.
For the connection to the VISCA RS-422
connector, see “Using the VISCA RS-422
Connector Plug” on page 10.
connector, see “Using the VISCA RS-422
Connector Plug” on page 10.
N VISCA FUNCTION switches
These switches are used for the VISCA
communication settings.
communication settings.
Switch 1 (RS-232C/RS-422 selector)
Set to ON for RS-422, or OFF for RS-232C.
Set to ON for RS-422, or OFF for RS-232C.
Switch 2 (Communication baud rate
selector)
Set to ON for 38400bps, or OFF for 9600bps.
selector)
Set to ON for 38400bps, or OFF for 9600bps.
2 3
1
IN EXT SYNC OUT
IN VISCA RS-232C OUT
CAMERA
~
AC IN
VISCA RS-422
AUDIO OUT
L
R
FUNCTION
1
6
RGB/COMPONENT
7 8
4
6
5
9
0
qd
qs
qf
qa