Panasonic NV-GS250GN User Manual
Before using
15
VQT0N73
≥Use the direction buttons (
π, ∑, ∏, ∫) and
[ENTER] button in place of the joystick on the
main unit.
main unit.
3
Press the [MENU] button to exit the menu
screen.
screen.
Setting date and time
If the screen shows the incorrect date/time, then
adjust it.
≥Set to Tape Recording Mode or Card
adjust it.
≥Set to Tape Recording Mode or Card
Recording Mode.
1
Set [BASIC] >> [CLOCK SET] >> [YES].
2
Move the joystick left or right in order to
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
2000, 2001, ..., 2089, 2000, ...
≥The 24-hour clock is used.
3
Press the joystick to determine the setting.
≥The clock function starts at [00] seconds.
≥The clock function starts at [00] seconds.
ª
About date/time
≥The date and time function are driven by a built-
in lithium battery.
≥Make sure to check the time before recording
because the built-in clock is not very accurate.
ª
Recharging the built-in lithium battery
≥If [
0] or [--] is indicated when the camera is
turned on, then the built-in lithium battery runs
down. Connect the AC adaptor to the camera or
place the battery on the camera, and the built-in
lithium battery will be recharged. Leave the
camera as is for approx. 24 hours, and the
battery will drive the date and time for approx. 6
months. (Even if the [OFF/ON] switch is set to
[OFF], the battery is still being recharged.)
down. Connect the AC adaptor to the camera or
place the battery on the camera, and the built-in
lithium battery will be recharged. Leave the
camera as is for approx. 24 hours, and the
battery will drive the date and time for approx. 6
months. (Even if the [OFF/ON] switch is set to
[OFF], the battery is still being recharged.)
WARNING
THE LITHIUM BATTERY IN THIS UNIT MUST
ONLY BE REPLACED BY QUALIFIED
PERSONNEL. IF THIS IS NECESSARY,
CONTACT THE PANASONIC CUSTOMER
CARE CENTRE ON 132600 FOR YOUR
NEAREST AUTHORIZED SERVICE CENTRE.
THE LITHIUM BATTERY IN THIS UNIT MUST
ONLY BE REPLACED BY QUALIFIED
PERSONNEL. IF THIS IS NECESSARY,
CONTACT THE PANASONIC CUSTOMER
CARE CENTRE ON 132600 FOR YOUR
NEAREST AUTHORIZED SERVICE CENTRE.
Adjusting LCD monitor/viewfinder
ª
Adjusting the brightness and colour
level
level
1
Set [SETUP] >> [LCD SET] or [EVF SET] >>
[YES].
[YES].
2
Move the joystick up or down in order to
select the item to be adjusted.
select the item to be adjusted.
[LCD SET]
:Brightness of the LCD monitor
:Colour level of the LCD monitor
[EVF SET]
:Brightness of the viewfinder
3
Move the joystick left or right to move the
bar indication representing the brightness.
bar indication representing the brightness.
4
Press the [MENU] button or the joystick to
complete the settings.
complete the settings.
≥In order to adjust the brightness of the
viewfinder, close the LCD monitor, and the
viewfinder will be activated.
viewfinder will be activated.
≥When the LCD monitor is rotated by 180°
towards the lens, the brightness of the LCD
monitor cannot be adjusted.
monitor cannot be adjusted.
≥These settings will not affect the images actually
recorded.
ª
In order to increase the brightness of
the entire LCD monitor
the entire LCD monitor
1
Press the [POWER LCD] button.
≥The [POWER LCD] lamp lights up.
≥If the [POWER LCD] button is pressed, the
≥If the [POWER LCD] button is pressed, the
entire LCD monitor will become approx. twice
as bright as the normal.
as bright as the normal.
ENTER
VAR.
SEARCH
MENU
ENTER
VAR.
SEARCH
MENU
EVF
POWER LCD
GS250GN.book 15 ページ ２００５年１月２６日 水曜日 午後１２時１７分