Panasonic NV-GS60GN User Manual
Before using
10
LSQT1174
ª
How to turn the power on and off with
the LCD monitor/viewfinder
the LCD monitor/viewfinder
When the power switch is set to [ON], the power
can be turned on and off with the LCD monitor
and the viewfinder when the unit is in Tape
Recording Mode.
can be turned on and off with the LCD monitor
and the viewfinder when the unit is in Tape
Recording Mode.
1
Open the LCD monitor out or extend the
viewfinder to use. (
viewfinder to use. (
-11-
)
≥The LCD monitor or the viewfinder will be
activated.
2
Close the LCD monitor and retract the
viewfinder.
viewfinder.
≥The power will not turn off unless the LCD
monitor is closed and the viewfinder is
retracted.
retracted.
≥The status indicator automatically goes off
and the power turns off. (If quick start is set to
[ON] (
[ON] (
-12-
), the unit goes into quick start
standby mode and the status indicator lights
green.)
green.)
≥The power does not turn off even if the LCD
monitor is closed and the viewfinder is
retracted while recording on a tape.
retracted while recording on a tape.
3
Open the LCD monitor or extend the
viewfinder to turn the power on and use the
movie camera again.
viewfinder to turn the power on and use the
movie camera again.
≥The status indicator lights red and the power
turns on.
Setting date and time
When the movie camera is turned on for the first
time, [SET DATE AND TIME] will appear.
time, [SET DATE AND TIME] will appear.
≥Select [YES] and press the centre of the
joystick. Do steps 2 and 3 below to set the date/
time.
time.
If the screen shows the incorrect date/time, then
adjust it.
≥Set to Tape Recording Mode.
adjust it.
≥Set to Tape Recording Mode.
1
Set [BASIC] >> [CLOCK SET] >> [YES]. (
-16-
)
2
Move the joystick left or right in order to
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
2000, 2001, ..., 2089, 2000, ...
≥The 24-hour clock is used.
3
Press the joystick to determine the setting.
≥The clock function starts at [00] seconds.
≥The clock function starts at [00] seconds.
ª
About date/time
≥The date and time function are driven by a
built-in lithium battery.
≥Make sure to check the time before recording
because the built-in clock is not very accurate.
ª
Recharging the built-in lithium battery
≥If [
0] or [--] is appears when the camera is
turned on, then the built-in lithium battery has
run down. Use the steps below to charge the
battery. When turn on the power for the first time
after charging, [SET DATE AND TIME] will
appear. Select [YES] and set the date and time.
Connect the AC adaptor to the camera or attach
the battery to the camera, and the built-in lithium
battery will be recharged. Leave the camera as
is for approx. 24 hours, and the battery will drive
the date and time for approx. 6 months. (Even if
the [OFF/ON] switch is set to [OFF], the battery
is still being recharged.)
run down. Use the steps below to charge the
battery. When turn on the power for the first time
after charging, [SET DATE AND TIME] will
appear. Select [YES] and set the date and time.
Connect the AC adaptor to the camera or attach
the battery to the camera, and the built-in lithium
battery will be recharged. Leave the camera as
is for approx. 24 hours, and the battery will drive
the date and time for approx. 6 months. (Even if
the [OFF/ON] switch is set to [OFF], the battery
is still being recharged.)
OFF
ON
OFF
ON
OFF
ON
LSQT1174ENG.book 10 ページ ２００７年１月２９日 月曜日 午後１時２８分