Panasonic NV-GS90 User Manual
Before using
13
LSQT1291
Setting date and time
When the movie camera is turned on for the first
time, [SET DATE AND TIME] will appear.
time, [SET DATE AND TIME] will appear.
≥Select [YES] and press the centre of the
joystick. Do steps 2 and 3 below to set the date/
time.
time.
If the screen shows the incorrect date/time, then
adjust it.
≥Set to Tape Recording Mode.
adjust it.
≥Set to Tape Recording Mode.
1
Set [BASIC] >> [CLOCK SET] >> [YES]. (
-18-
)
2
Move the joystick left or right in order to
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
2000, 2001, ..., 2089, 2000, ...
≥The 24-hour clock is used.
3
Press the joystick to determine the setting.
≥The clock function starts at [00] seconds.
≥The clock function starts at [00] seconds.
ª
About date/time
≥The date and time function are driven by a
built-in lithium battery.
≥Make sure to check the time before recording
because the built-in clock is not very accurate.
ª
Recharging the built-in lithium battery
≥If [
0] or [--] appears when the camera is
turning on, then the built-in lithium battery has
run down. Use the steps below to charge the
battery. When turn on the power for the first time
after charging, [SET DATE AND TIME] will
appear. Select [YES] and set the date and time.
Connect the AC adaptor to the camera or attach
the battery to the camera, and the built-in lithium
battery will be recharged. Leave the camera as
is for approx. 24 hours, and the battery will drive
the date and time for approx. 6 months. (The
battery is still being recharged even if the mode
dial is set to OFF.)
run down. Use the steps below to charge the
battery. When turn on the power for the first time
after charging, [SET DATE AND TIME] will
appear. Select [YES] and set the date and time.
Connect the AC adaptor to the camera or attach
the battery to the camera, and the built-in lithium
battery will be recharged. Leave the camera as
is for approx. 24 hours, and the battery will drive
the date and time for approx. 6 months. (The
battery is still being recharged even if the mode
dial is set to OFF.)
Using the LCD monitor
You can record the image while viewing it on the
opened LCD monitor.
opened LCD monitor.
1
Put a finger on the LCD monitor open part
and pull the LCD monitor out in the
direction of the arrow.
and pull the LCD monitor out in the
direction of the arrow.
≥It can open up to 90o.
2
Adjust the angle of the LCD monitor
according to your preference.
according to your preference.
≥It can rotate up to 180o 1 towards the lens or
90
o 2 towards the viewfinder.
≥The brightness and colour level of the LCD
monitor can be adjusted from the menu.
≥If it is forcibly opened or rotated, the camera
may be damaged or fail.
≥If the LCD monitor is rotated by 180o towards
the lens and the viewfinder is extended (when
recording yourself), the LCD monitor and the
viewfinder simultaneously light.
recording yourself), the LCD monitor and the
viewfinder simultaneously light.
WARNING
THE LITHIUM BATTERY IN THIS
EQUIPMENT MUST ONLY BE REPLACED
BY QUALIFIED PERSONNEL. WHEN
NECESSARY, CONTACT YOUR LOCAL
PANASONIC SUPPLIER.
THE LITHIUM BATTERY IN THIS
EQUIPMENT MUST ONLY BE REPLACED
BY QUALIFIED PERSONNEL. WHEN
NECESSARY, CONTACT YOUR LOCAL
PANASONIC SUPPLIER.
LSQT1291_ENG.book 13 ページ ２００８年３月５日 水曜日 午前９時４１分