Panasonic DVX100B User Manual
44
Switching Audio Input
You can record audio through two channels when
shooting (see the table below). You can switch the
source for each channel between the built-in
microphone, another microphone, or audio
equipment connected to the camera.
shooting (see the table below). You can switch the
source for each channel between the built-in
microphone, another microphone, or audio
equipment connected to the camera.
1
Switch the CH1 SELECT switch to INT (L).
• Audio from the built-in microphone Lch is
• Audio from the built-in microphone Lch is
recorded to audio channel 1.
2
Switch the CH2 SELECT switch to INT (R).
• Audio from the built-in microphone Rch is
• Audio from the built-in microphone Rch is
recorded to audio channel 2.
1
Connect an external microphone or audio
equipment to the INPUT 1/2 (XLR 3-pin)
terminal. (Page 59)
equipment to the INPUT 1/2 (XLR 3-pin)
terminal. (Page 59)
2
Use the INPUT 1/2 switch to switch the audio
input.
LINE: (audio equipment is connected)
input.
LINE: (audio equipment is connected)
Input level is 0 dBu.
MIC: (another microphone is connected)
Input level is -50 dBu.
You can change the input level to -60 dBu in
the setup menus, RECORDING SETUP
screen MIC GAIN 1 and MIC GAIN 2 (Page
74). Be aware that sensitivity will be higher if
you choose -60 dBu so you will record more
noise.
You can change the input level to -60 dBu in
the setup menus, RECORDING SETUP
screen MIC GAIN 1 and MIC GAIN 2 (Page
74). Be aware that sensitivity will be higher if
you choose -60 dBu so you will record more
noise.
3
When using the phantom microphone, set the
INPUT 1/2 (MIC POWER +48V) switch to ON.
ON: (When using the phantom microphone)
INPUT 1/2 (MIC POWER +48V) switch to ON.
ON: (When using the phantom microphone)
48V power supply to INPUT 1/2 terminal.
OFF: (When a phantom microphone is not
connected)
connected)
No power supply for INPUT 1/2 terminal.
• The battery will discharge faster if you use a
phantom microphone.
• Set to OFF if you connect equipment not
compatible with +48V. You can damage such
equipment if you leave the setting at ON.
equipment if you leave the setting at ON.
4
Use the CH1 SELECT switch to select the
input signal to be recorded to audio channel 1.
INT (L): Audio from the built-in microphone Lch
is recorded to audio channel 1.
INPUT 1: Audio from a device connected to
INPUT 1 terminal is recorded to channel 1.
INPUT 2: Audio from a device connected to
INPUT 2 terminal is recorded to channel 1.
input signal to be recorded to audio channel 1.
INT (L): Audio from the built-in microphone Lch
is recorded to audio channel 1.
INPUT 1: Audio from a device connected to
INPUT 1 terminal is recorded to channel 1.
INPUT 2: Audio from a device connected to
INPUT 2 terminal is recorded to channel 1.
5
Use the CH2 SELECT switch to select the
input signal to be recorded to audio channel 2.
INT (R):
input signal to be recorded to audio channel 2.
INT (R):
Audio from the built-in microphone Rch is
recorded to audio channel 2.
recorded to audio channel 2.
INPUT 2:
Audio from a device connected to INPUT 2
terminal is recorded to channel 2.
terminal is recorded to channel 2.
Use the AUDIO control knob to adjust the recording
level of the built-in microphone or of audio signals
input through the INPUT 1/2 (XLR 3-pin) terminal.
To adjust the volume of the sound for monitoring
(Page 36).
Leave it in the center position under normal
conditions.
Adjust the record level of audio signal using this
knob, regardless of the settings of MIC ALC items
in the RECORDING SETUP screen of setting
menu. (Page 74).
• The audio signals input into AUDIO IN/OUT CH1/
level of the built-in microphone or of audio signals
input through the INPUT 1/2 (XLR 3-pin) terminal.
To adjust the volume of the sound for monitoring
(Page 36).
Leave it in the center position under normal
conditions.
Adjust the record level of audio signal using this
knob, regardless of the settings of MIC ALC items
in the RECORDING SETUP screen of setting
menu. (Page 74).
• The audio signals input into AUDIO IN/OUT CH1/
CH2 (pin jack) terminals can not be adjusted.
Built-in microphone L
CH1
Built-in microphone R
CH2
INPUT 1 (XLR)
CH1
INPUT 2 (XLR)
CH2
Using the built-in microphone
Using another microphone and audio
equipment
equipment
CH1 SELECT switch
CH2 SELECT switch
INPUT 1/2 (MIC
POWER +48V)
Switch
POWER +48V)
Switch
INPUT 1/2 switches
AUDIO control knob
• When inputting the microphone signal to
channels 1 and 2, connect the microphone to
INPUT 2 and switch both CH1 SELECT and
CH2 SELECT to INPUT 2.
INPUT 2 and switch both CH1 SELECT and
CH2 SELECT to INPUT 2.
Adjusting the recording level