Panasonic AJ-SDC905p User Manual

81

P.OFF GPS DATA

HOLD
CLEAR

For selecting whether or not to hold the UMID
GPS position information while the power is
off and record the information as the data still
held as the previous value until another
measurement can be taken after the power is
next turned on.
HOLD: The data is held and recorded.
CLEAR: The data is cleared at the same time

as the power is turned off, and all
zeros (no information) are recorded
from the time the power is turned on
until the measurement is next taken.

COMPONENT OUT

OFF
BETACAM
M2

For setting the analog component signal
output level.
OFF:

Output stops during power save. (Note that
this setting is forced ON if a camera
adapter is connected and a tally signal is
detected from pin 26.  Otherwise it is OFF.)

Output at the ß-CAM level.

Output at the M II level.

The underlining in the variable range column indicates the setting in the preset
mode.

C U F

C U F

1394 TYPE

DVCPRO
DV

For setting the format of the signals to be
output from the DVCPRO connector.
DVCPRO:

The signals are output in the DVCPRO
(25M) format.

The signals are output in the DV format.

<Note> 
The signals are output in the DVCPRO50
format if 16:9/50M or 4:3/50M is selected as
the REC MODE menu item setting on the
<SYSTEM MODE> screen.

C U F

1394 AUDIO IN

CH1/CH2
CH3/CH4

For selecting the channel on which the
reception data is to be recorded on the tape
when receiving DV format data in the 4CH
audio signal mode and recording the data on
a DVCPRO (25M) tape.
CH1/CH2:

The reception data is recorded on CH1 and
CH2.

The reception data is recorded on CH3 and
CH4.

C U F

1394 SPEED

S100
S200
S400

For setting the transfer speed of the signals to
be output from the DVCPRO connector.
S100: 100 Mbps
S200: 200 Mbps
S400: 400 Mbps

C U F

1394 IN CH

0

: 

63
AUTO

For setting the input channel for the signals to
be supplied to the DVCPRO connector.
0-63:

The channel is fixed at the specified
number.

The channel corresponding to the setting of
the externally connected unit is selected.

C U F

1394 OUT CH

0

: 

63
AUTO

For setting the output channel for the signals
to be output from the DVCPRO connector
0-63:

The channel is fixed at the specified
number.

The channel corresponding to the setting of
the externally connected unit is selected.

C U F

26PIN VIDEO
SELECT

COMPONENT
VIDEO OUT

For setting the video signals to be output from
pin #4 of the 26-pin connector when a 26-pin
camera adapter is connected.
COMPONENT:

The component Y signal is output.

The same signal (composite signal) as the
VIDEO OUT connector signal is output.

C U F

26PIN CTL
DEFAULT

NORMAL
SPECIAL

For setting the control signal of the VTR to be
output from pin #12 of the 26-pin connector
when using a VTR connected to a 26-pin
camera adapter.
NORMAL:

STOP “low,” START “high” (for AJ-D92)

STOP “high,” START “low”

C U F

26PIN CONTROL

OFF
BOTH

For setting whether recording is to be
controlled by the unit or by both the unit and
the external VTR which is connected to the
26-pin camera adapter.
OFF:

Recording is performed by the unit only.  (It
is not performed using the external VTR.)

Recording is performed by both the unit
and the external VTR.  The tally lamp
indicates the status of the tally signal of the
26-pin connector.  (The tally lamp setting
can be established using REC TALLY in
the SYSTEM MODE.)

C U F