Panasonic GR-DX300 User Manual

EN

The audio track can be customized only when recorded
in the 12-bit mode (

墌

 pg. 32).

● Audio Dubbing is not possible on a tape recorded in

16-bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.

● To perform Audio Dubbing while watching on the

television, make connections (

墌

 pg. 16).

Play back the tape to locate the point where editing

will start, then press PAUSE (6) 

H

.

While holding A.DUB (e) 

S

 on the remote control,

press PAUSE (6) 

H

. “6e” 

O

 and “MIC” appear.

Press PLAY (4) 

D

, then begin “narrating”.

Speak into the microphone.

• To pause dubbing, press PAUSE (6) 

H

.

To end Audio Dubbing, press PAUSE (6) 

H

, then

STOP (5) 

G

.

..... set “12bit MODE” to “SOUND 2” or “MIX” in the

Menu Screen (

墌

 pg. 36).

● Sound is not heard from the speaker during Audio

Dubbing.

● When editing onto a tape that was recorded at 12-bit, the

old and new soundtracks are recorded separately.

● If you dub onto a blank space on the tape, the sound may

be disrupted. Make sure you only edit recorded areas.

● If feedback or howling occurs during TV playback, move

the camcorder’s microphone away from the TV, or turn
down the TV’s volume.

● If you change from 12-bit to 16-bit  in mid-recording and

then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.

● During Audio Dubbing, when the tape moves to scenes

recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops (

墌

 pg. 56).

● To perform Audio Dubbing with a video unit connected to

the camcorder’s S/AV connector 

&

, first set “S/AV

INPUT” to “A/V IN” or “S IN” in the Menu Screen
(

墌

 pg. 35). “AUX” appears instead of  “MIC”.

You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.

● Before performing the following steps, make sure that

“TIME CODE” is set to “ON” in the Menu Screen
(

墌

 pg. 35, 36).

● Insert Editing is not possible on a tape recorded in the LP

mode or on a blank portion of a tape.

● To perform Insert Editing while watching in the television,

make connections (

墌

 pg. 16).

Play back the tape, locate the Edit-Out point and

press PAUSE (6) 

H

. Confirm the time code at this

point (

墌

 pg. 35, 36).

Press REW (2) 

a

 until the Edit-In point is located,

then press PAUSE (6) 

H

.

Press and hold INSERT (w) 

A

 on the remote

control, then press PAUSE (6) 

H

. “6w” 

0

 and the

Time Code (min.:sec.) appear and the camcorder
enters Insert-Pause mode.

Press START/STOP 

k

 to begin editing.

• Confirm the insert at the time code you checked in

step 1.

• To pause editing, press START/STOP 

k

. Press it

again to resume editing.

To end Insert Editing, press START/STOP 

k

, then

STOP (5) 

7

.

● Programme AE with special effects (

墌

 pg. 27) can be

used to spice up the scenes being edited during Insert
Editing.

● During Insert Editing, the date and time information

changes.

● If you perform Insert Editing onto a blank space on the

tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.

● During Insert Editing, when the tape moves to scenes

recorded in the LP mode or a blank portion, Insert Editing
stops (

墌

 pg. 56).

● If a memory card is loaded and “NAVIGATION” is set to

“ON”, a NAVIGATION thumbnail image is stored in the
memory card (

墌

 pg. 21).

R

j

I

s

g

f

U

P

a

O

d

k

l

;

A

S

D

F

G

H

h

K

J

Y

T

  01 DX300/100/95/75EK_EN 35-44

2/26/03, 7:13 PM

40